Minki/linux
1
0
Fork 1
mirror of https://github.com/torvalds/linux.git synced 2024-11-07 12:41:55 +00:00
Code Issues Packages Projects Releases Wiki Activity
f7a437dda2
linux/drivers/ata/ahci.h
Tejun Heo 6b7ae9545a libata: reimplement link power management 
The current LPM implementation has the following issues.

* Operation order isn't well thought-out.  e.g. HIPM should be
  configured after IPM in SControl is properly configured.  Not the
  other way around.

* Suspend/resume paths call ata_lpm_enable/disable() which must only
  be called from EH context directly.  Also, ata_lpm_enable/disable()
  were called whether LPM was in use or not.

* Implementation is per-port when it should be per-link.  As a result,
  it can't be used for controllers with slave links or PMP.

* LPM state isn't managed consistently.  After a link reset for
  whatever reason including suspend/resume the actual LPM state would
  be reset leaving ap->lpm_policy inconsistent.

* Generic/driver-specific logic boundary isn't clear.  Currently,
  libahci has to mangle stuff which libata EH proper should be
  handling.  This makes the implementation unnecessarily complex and
  fragile.

* Tied to ALPM.  Doesn't consider DIPM only cases and doesn't check
  whether the device allows HIPM.

* Error handling isn't implemented.

Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense.  This patch reimplements
LPM support.

* The new implementation is per-link.  The target policy is still
  port-wide (ap->target_lpm_policy) but all the mechanisms and states
  are per-link and integrate well with the rest of link abstraction
  and can work with slave and PMP links.

* Core EH has proper control of LPM state.  LPM state is reconfigured
  when and only when reconfiguration is necessary.  It makes sure that
  LPM state is reset when probing for new device on the link.
  Controller agnostic logic is now implemented in libata EH proper and
  driver implementation only has to deal with controller specifics.

* Proper error handling.  LPM config failure is attributed to the
  device on the link and LPM is disabled for the link if it fails
  repeatedly.

* ops->enable/disable_pm() are replaced with single ops->set_lpm()
  which takes @policy and @hints.  This simplifies driver specific
  implementation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-10-21 20:21:04 -04:00

354 lines
13 KiB
C
Raw Blame History

/*
* ahci.h - Common AHCI SATA definitions and declarations
*
* Maintained by: Jeff Garzik <jgarzik@pobox.com>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
* Copyright 2004-2005 Red Hat, Inc.
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
*
*
* libata documentation is available via 'make {ps|pdf}docs',
* as Documentation/DocBook/libata.*
*
* AHCI hardware documentation:
* http://www.intel.com/technology/serialata/pdf/rev1_0.pdf
* http://www.intel.com/technology/serialata/pdf/rev1_1.pdf
*
*/
#ifndef _AHCI_H
#define _AHCI_H
#include <linux/libata.h>
/* Enclosure Management Control */
#define EM_CTRL_MSG_TYPE 0x000f0000
/* Enclosure Management LED Message Type */
#define EM_MSG_LED_HBA_PORT 0x0000000f
#define EM_MSG_LED_PMP_SLOT 0x0000ff00
#define EM_MSG_LED_VALUE 0xffff0000
#define EM_MSG_LED_VALUE_ACTIVITY 0x00070000
#define EM_MSG_LED_VALUE_OFF 0xfff80000
#define EM_MSG_LED_VALUE_ON 0x00010000
enum {
AHCI_MAX_PORTS = 32,
AHCI_MAX_SG = 168, /* hardware max is 64K */
AHCI_DMA_BOUNDARY = 0xffffffff,
AHCI_MAX_CMDS = 32,
AHCI_CMD_SZ = 32,
AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ,
AHCI_RX_FIS_SZ = 256,
AHCI_CMD_TBL_CDB = 0x40,
AHCI_CMD_TBL_HDR_SZ = 0x80,
AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16),
AHCI_CMD_TBL_AR_SZ = AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS,
AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ +
AHCI_RX_FIS_SZ,
AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ +
AHCI_CMD_TBL_AR_SZ +
(AHCI_RX_FIS_SZ * 16),
AHCI_IRQ_ON_SG = (1 << 31),
AHCI_CMD_ATAPI = (1 << 5),
AHCI_CMD_WRITE = (1 << 6),
AHCI_CMD_PREFETCH = (1 << 7),
AHCI_CMD_RESET = (1 << 8),
AHCI_CMD_CLR_BUSY = (1 << 10),
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
RX_FIS_SDB = 0x58, /* offset of SDB FIS data */
RX_FIS_UNK = 0x60, /* offset of Unknown FIS data */
/* global controller registers */
HOST_CAP = 0x00, /* host capabilities */
HOST_CTL = 0x04, /* global host control */
HOST_IRQ_STAT = 0x08, /* interrupt status */
HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */
HOST_VERSION = 0x10, /* AHCI spec. version compliancy */
HOST_EM_LOC = 0x1c, /* Enclosure Management location */
HOST_EM_CTL = 0x20, /* Enclosure Management Control */
HOST_CAP2 = 0x24, /* host capabilities, extended */
/* HOST_CTL bits */
HOST_RESET = (1 << 0), /* reset controller; self-clear */
HOST_IRQ_EN = (1 << 1), /* global IRQ enable */
HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
/* HOST_CAP bits */
HOST_CAP_SXS = (1 << 5), /* Supports External SATA */
HOST_CAP_EMS = (1 << 6), /* Enclosure Management support */
HOST_CAP_CCC = (1 << 7), /* Command Completion Coalescing */
HOST_CAP_PART = (1 << 13), /* Partial state capable */
HOST_CAP_SSC = (1 << 14), /* Slumber state capable */
HOST_CAP_PIO_MULTI = (1 << 15), /* PIO multiple DRQ support */
HOST_CAP_FBS = (1 << 16), /* FIS-based switching support */
HOST_CAP_PMP = (1 << 17), /* Port Multiplier support */
HOST_CAP_ONLY = (1 << 18), /* Supports AHCI mode only */
HOST_CAP_CLO = (1 << 24), /* Command List Override support */
HOST_CAP_LED = (1 << 25), /* Supports activity LED */
HOST_CAP_ALPM = (1 << 26), /* Aggressive Link PM support */
HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
HOST_CAP_MPS = (1 << 28), /* Mechanical presence switch */
HOST_CAP_SNTF = (1 << 29), /* SNotification register */
HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
/* HOST_CAP2 bits */
HOST_CAP2_BOH = (1 << 0), /* BIOS/OS handoff supported */
HOST_CAP2_NVMHCI = (1 << 1), /* NVMHCI supported */
HOST_CAP2_APST = (1 << 2), /* Automatic partial to slumber */
/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */
PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */
PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */
PORT_IRQ_STAT = 0x10, /* interrupt status */
PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */
PORT_CMD = 0x18, /* port command */
PORT_TFDATA = 0x20, /* taskfile data */
PORT_SIG = 0x24, /* device TF signature */
PORT_CMD_ISSUE = 0x38, /* command issue */
PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */
PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */
PORT_SCR_ERR = 0x30, /* SATA phy register: SError */
PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
PORT_SCR_NTF = 0x3c, /* SATA phy register: SNotification */
PORT_FBS = 0x40, /* FIS-based Switching */
/* PORT_IRQ_{STAT,MASK} bits */
PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
PORT_IRQ_TF_ERR = (1 << 30), /* task file error */
PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */
PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */
PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */
PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */
PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */
PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
PORT_IRQ_DEV_ILCK = (1 << 7), /* device interlock */
PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */
PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */
PORT_IRQ_SDB_FIS = (1 << 3), /* Set Device Bits FIS rx'd */
PORT_IRQ_DMAS_FIS = (1 << 2), /* DMA Setup FIS rx'd */
PORT_IRQ_PIOS_FIS = (1 << 1), /* PIO Setup FIS rx'd */
PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */
PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR |
PORT_IRQ_IF_ERR |
PORT_IRQ_CONNECT |
PORT_IRQ_PHYRDY |
PORT_IRQ_UNK_FIS |
PORT_IRQ_BAD_PMP,
PORT_IRQ_ERROR = PORT_IRQ_FREEZE |
PORT_IRQ_TF_ERR |
PORT_IRQ_HBUS_DATA_ERR,
DEF_PORT_IRQ = PORT_IRQ_ERROR | PORT_IRQ_SG_DONE |
PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS |
PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
/* PORT_CMD bits */
PORT_CMD_ASP = (1 << 27), /* Aggressive Slumber/Partial */
PORT_CMD_ALPE = (1 << 26), /* Aggressive Link PM enable */
PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
PORT_CMD_FBSCP = (1 << 22), /* FBS Capable Port */
PORT_CMD_PMP = (1 << 17), /* PMP attached */
PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */
PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */
PORT_CMD_CLO = (1 << 3), /* Command list override */
PORT_CMD_POWER_ON = (1 << 2), /* Power up device */
PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */
PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */
PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */
PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */
PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */
PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */
PORT_FBS_SDE = (1 << 2), /* FBS single device error */
PORT_FBS_DEC = (1 << 1), /* FBS device error clear */
PORT_FBS_EN = (1 << 0), /* Enable FBS */
/* hpriv->flags bits */
AHCI_HFLAG_NO_NCQ = (1 << 0),
AHCI_HFLAG_IGN_IRQ_IF_ERR = (1 << 1), /* ignore IRQ_IF_ERR */
AHCI_HFLAG_IGN_SERR_INTERNAL = (1 << 2), /* ignore SERR_INTERNAL */
AHCI_HFLAG_32BIT_ONLY = (1 << 3), /* force 32bit */
AHCI_HFLAG_MV_PATA = (1 << 4), /* PATA port */
AHCI_HFLAG_NO_MSI = (1 << 5), /* no PCI MSI */
AHCI_HFLAG_NO_PMP = (1 << 6), /* no PMP */
AHCI_HFLAG_SECT255 = (1 << 8), /* max 255 sectors */
AHCI_HFLAG_YES_NCQ = (1 << 9), /* force NCQ cap on */
AHCI_HFLAG_NO_SUSPEND = (1 << 10), /* don't suspend */
AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = (1 << 11), /* treat SRST timeout as
link offline */
AHCI_HFLAG_NO_SNTF = (1 << 12), /* no sntf */
AHCI_HFLAG_NO_FPDMA_AA = (1 << 13), /* no FPDMA AA */
AHCI_HFLAG_YES_FBS = (1 << 14), /* force FBS cap on */
/* ap->flags bits */
AHCI_FLAG_COMMON = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
ATA_FLAG_ACPI_SATA | ATA_FLAG_AN |
ATA_FLAG_LPM,
ICH_MAP = 0x90, /* ICH MAP register */
/* em constants */
EM_MAX_SLOTS = 8,
EM_MAX_RETRY = 5,
/* em_ctl bits */
EM_CTL_RST = (1 << 9), /* Reset */
EM_CTL_TM = (1 << 8), /* Transmit Message */
EM_CTL_MR = (1 << 0), /* Message Recieved */
EM_CTL_ALHD = (1 << 26), /* Activity LED */
EM_CTL_XMT = (1 << 25), /* Transmit Only */
EM_CTL_SMB = (1 << 24), /* Single Message Buffer */
/* em message type */
EM_MSG_TYPE_LED = (1 << 0), /* LED */
EM_MSG_TYPE_SAFTE = (1 << 1), /* SAF-TE */
EM_MSG_TYPE_SES2 = (1 << 2), /* SES-2 */
EM_MSG_TYPE_SGPIO = (1 << 3), /* SGPIO */
};
struct ahci_cmd_hdr {
__le32 opts;
__le32 status;
__le32 tbl_addr;
__le32 tbl_addr_hi;
__le32 reserved[4];
};
struct ahci_sg {
__le32 addr;
__le32 addr_hi;
__le32 reserved;
__le32 flags_size;
};
struct ahci_em_priv {
enum sw_activity blink_policy;
struct timer_list timer;
unsigned long saved_activity;
unsigned long activity;
unsigned long led_state;
};
struct ahci_port_priv {
struct ata_link *active_link;
struct ahci_cmd_hdr *cmd_slot;
dma_addr_t cmd_slot_dma;
void *cmd_tbl;
dma_addr_t cmd_tbl_dma;
void *rx_fis;
dma_addr_t rx_fis_dma;
/* for NCQ spurious interrupt analysis */
unsigned int ncq_saw_d2h:1;
unsigned int ncq_saw_dmas:1;
unsigned int ncq_saw_sdb:1;
u32 intr_mask; /* interrupts to enable */
bool fbs_supported; /* set iff FBS is supported */
bool fbs_enabled; /* set iff FBS is enabled */
int fbs_last_dev; /* save FBS.DEV of last FIS */
/* enclosure management info per PM slot */
struct ahci_em_priv em_priv[EM_MAX_SLOTS];
};
struct ahci_host_priv {
void __iomem * mmio; /* bus-independant mem map */
unsigned int flags; /* AHCI_HFLAG_* */
u32 cap; /* cap to use */
u32 cap2; /* cap2 to use */
u32 port_map; /* port map to use */
u32 saved_cap; /* saved initial cap */
u32 saved_cap2; /* saved initial cap2 */
u32 saved_port_map; /* saved initial port_map */
u32 em_loc; /* enclosure management location */
u32 em_buf_sz; /* EM buffer size in byte */
u32 em_msg_type; /* EM message type */
};
extern int ahci_ignore_sss;
extern struct device_attribute *ahci_shost_attrs[];
extern struct device_attribute *ahci_sdev_attrs[];
#define AHCI_SHT(drv_name) \
ATA_NCQ_SHT(drv_name), \
.can_queue = AHCI_MAX_CMDS - 1, \
.sg_tablesize = AHCI_MAX_SG, \
.dma_boundary = AHCI_DMA_BOUNDARY, \
.shost_attrs = ahci_shost_attrs, \
.sdev_attrs = ahci_sdev_attrs
extern struct ata_port_operations ahci_ops;
void ahci_save_initial_config(struct device *dev,
struct ahci_host_priv *hpriv,
unsigned int force_port_map,
unsigned int mask_port_map);
void ahci_init_controller(struct ata_host *host);
int ahci_reset_controller(struct ata_host *host);
int ahci_do_softreset(struct ata_link *link, unsigned int *class,
int pmp, unsigned long deadline,
int (*check_ready)(struct ata_link *link));
int ahci_stop_engine(struct ata_port *ap);
void ahci_start_engine(struct ata_port *ap);
int ahci_check_ready(struct ata_link *link);
int ahci_kick_engine(struct ata_port *ap);
void ahci_set_em_messages(struct ahci_host_priv *hpriv,
struct ata_port_info *pi);
int ahci_reset_em(struct ata_host *host);
irqreturn_t ahci_interrupt(int irq, void *dev_instance);
void ahci_print_info(struct ata_host *host, const char *scc_s);
static inline void __iomem *__ahci_port_base(struct ata_host *host,
unsigned int port_no)
{
struct ahci_host_priv *hpriv = host->private_data;
void __iomem *mmio = hpriv->mmio;
return mmio + 0x100 + (port_no * 0x80);
}
static inline void __iomem *ahci_port_base(struct ata_port *ap)
{
return __ahci_port_base(ap->host, ap->port_no);
}
static inline int ahci_nr_ports(u32 cap)
{
return (cap & 0x1f) + 1;
}
#endif /* _AHCI_H */
Reference in New Issue View Git Blame Copy Permalink