Bin Liu cb83df77f3 usb: musb: cppi41: improve rx channel abort routine ... 1. set AUTOREQ to NONE at the beginning of teardown; 2. add delay for dma pipeline to drain; 3. Do not set USB_TDOWN bit for RX teardown. The CPPI hw has an issue that when tearing down a RX channel, if another RX channel is receiving data, the CPPI will lockup. To workaround the issue, do not set the CPPI TD bit. The steps before this point ensures the CPPI channel will be torn down properly. Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>		2015-01-27 09:34:58 -06:00
..
am35x.c	usb: musb: Change end point selection to use new IO access	2014-11-25 08:47:06 -06:00
blackfin.c	usb: musb: blackfin: fix build break	2014-12-22 10:24:10 -06:00
blackfin.h
cppi_dma.c	usb: musb: dma: merge ->start/stop into create/destroy	2013-07-29 13:53:18 +03:00
cppi_dma.h
da8xx.c	usb: musb: Pass fifo_mode in platform data	2014-11-25 08:47:07 -06:00
davinci.c	usb: move the OTG state from the USB PHY to the OTG structure	2014-11-03 10:01:25 -06:00
davinci.h
jz4740.c	usb: musb: Pass fifo_mode in platform data	2014-11-25 08:47:07 -06:00
Kconfig	usb: musb: Fix randconfig build issues for Kconfig options	2014-12-22 10:26:06 -06:00
Makefile	usb: musb: add support for JZ4740 usb device controller	2013-12-20 09:53:24 -06:00
musb_am335x.c	usb: musb: Fix panic upon musb_am335x module removal	2014-06-27 10:53:06 -05:00
musb_core.c	Driver core patches for 3.19-rc1	2014-12-14 16:10:09 -08:00
musb_core.h	usb: musb: Use IS_ENABLED for tusb6010	2014-11-25 08:47:07 -06:00
musb_cppi41.c	usb: musb: cppi41: improve rx channel abort routine	2015-01-27 09:34:58 -06:00
musb_debug.h
musb_debugfs.c	Linux 3.19-rc5	2015-01-19 09:57:20 -06:00
musb_dma.h	usb: musb: introduce dma_channel.rx_packet_done	2014-06-30 14:26:24 -05:00
musb_dsps.c	usb: musb: Change end point selection to use new IO access	2014-11-25 08:47:06 -06:00
musb_gadget_ep0.c	usb: musb: gadget: read ep0 fifo only if rxcount is non zero	2013-04-02 11:42:50 +03:00
musb_gadget.c	usb: musb: gadget: use udc-core's reset notifier	2014-11-10 17:19:34 -06:00
musb_gadget.h	usb: musb: add Kconfig options for HOST, GAGDET or DUAL_ROLE modes	2013-05-28 19:22:23 +03:00
musb_host.c	usb: musb: stuff leak of struct usb_hcd	2014-12-22 10:36:24 -06:00
musb_host.h	usb: musb: fix prototype for musb_port_reset	2013-12-20 15:05:43 -06:00
musb_io.h	usb: musb: Change end point selection to use new IO access	2014-11-25 08:47:06 -06:00
musb_regs.h	usb: musb: Use IS_ENABLED for tusb6010	2014-11-25 08:47:07 -06:00
musb_virthub.c	usb: musb: virthub: use HUB_CHAR_*	2015-01-27 09:34:52 -06:00
musbhsdma.c	usb: musb: Change end point selection to use new IO access	2014-11-25 08:47:06 -06:00
musbhsdma.h	usb: musb: remove generic_interrupt	2012-11-06 15:32:13 +02:00
omap2430.c	usb: move the OTG state from the USB PHY to the OTG structure	2014-11-03 10:01:25 -06:00
omap2430.h	usb: start using the control module driver	2013-01-25 12:27:24 +02:00
tusb6010_omap.c	usb: musb: tusb6010: Use musb->tusb_revision instead of tusb_get_revision call.	2014-05-16 12:16:31 -05:00
tusb6010.c	usb: musb: Change end point selection to use new IO access	2014-11-25 08:47:06 -06:00
tusb6010.h	usb: musb: tusb6010: Use musb->tusb_revision instead of tusb_get_revision call.	2014-05-16 12:16:31 -05:00
ux500_dma.c	usb: musb: Change to use new IO access	2014-11-25 08:47:06 -06:00
ux500.c	usb: musb: Pass fifo_mode in platform data	2014-11-25 08:47:07 -06:00