mirror of
https://github.com/torvalds/linux.git
synced 2024-11-05 03:21:32 +00:00
a342d215c2
A number of drivers in drivers/gpio return -ENODEV when confronted with missing setup parameters such as the platform data. However, returning -ENODEV causes the driver layer to silently ignore the driver as it assumes the probe did not find anything and was only speculative. To make life easier to discern why a driver is not being attached, change to returning -EINVAL, which is a better description of the fact that the driver data was not valid. Also add a set of dev_dbg() statements to the error paths to provide an better explanation of the error as there may be more that one point in the driver. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
391 lines
9.4 KiB
C
391 lines
9.4 KiB
C
/*
|
|
* max732x.c - I2C Port Expander with 8/16 I/O
|
|
*
|
|
* Copyright (C) 2007 Marvell International Ltd.
|
|
* Copyright (C) 2008 Jack Ren <jack.ren@marvell.com>
|
|
* Copyright (C) 2008 Eric Miao <eric.miao@marvell.com>
|
|
*
|
|
* Derived from drivers/gpio/pca953x.c
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; version 2 of the License.
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/init.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/string.h>
|
|
#include <linux/gpio.h>
|
|
|
|
#include <linux/i2c.h>
|
|
#include <linux/i2c/max732x.h>
|
|
|
|
|
|
/*
|
|
* Each port of MAX732x (including MAX7319) falls into one of the
|
|
* following three types:
|
|
*
|
|
* - Push Pull Output
|
|
* - Input
|
|
* - Open Drain I/O
|
|
*
|
|
* designated by 'O', 'I' and 'P' individually according to MAXIM's
|
|
* datasheets.
|
|
*
|
|
* There are two groups of I/O ports, each group usually includes
|
|
* up to 8 I/O ports, and is accessed by a specific I2C address:
|
|
*
|
|
* - Group A : by I2C address 0b'110xxxx
|
|
* - Group B : by I2C address 0b'101xxxx
|
|
*
|
|
* where 'xxxx' is decided by the connections of pin AD2/AD0. The
|
|
* address used also affects the initial state of output signals.
|
|
*
|
|
* Within each group of ports, there are five known combinations of
|
|
* I/O ports: 4I4O, 4P4O, 8I, 8P, 8O, see the definitions below for
|
|
* the detailed organization of these ports.
|
|
*
|
|
* GPIO numbers start from 'gpio_base + 0' to 'gpio_base + 8/16',
|
|
* and GPIOs from GROUP_A are numbered before those from GROUP_B
|
|
* (if there are two groups).
|
|
*
|
|
* NOTE: MAX7328/MAX7329 are drop-in replacements for PCF8574/a, so
|
|
* they are not supported by this driver.
|
|
*/
|
|
|
|
#define PORT_NONE 0x0 /* '/' No Port */
|
|
#define PORT_OUTPUT 0x1 /* 'O' Push-Pull, Output Only */
|
|
#define PORT_INPUT 0x2 /* 'I' Input Only */
|
|
#define PORT_OPENDRAIN 0x3 /* 'P' Open-Drain, I/O */
|
|
|
|
#define IO_4I4O 0x5AA5 /* O7 O6 I5 I4 I3 I2 O1 O0 */
|
|
#define IO_4P4O 0x5FF5 /* O7 O6 P5 P4 P3 P2 O1 O0 */
|
|
#define IO_8I 0xAAAA /* I7 I6 I5 I4 I3 I2 I1 I0 */
|
|
#define IO_8P 0xFFFF /* P7 P6 P5 P4 P3 P2 P1 P0 */
|
|
#define IO_8O 0x5555 /* O7 O6 O5 O4 O3 O2 O1 O0 */
|
|
|
|
#define GROUP_A(x) ((x) & 0xffff) /* I2C Addr: 0b'110xxxx */
|
|
#define GROUP_B(x) ((x) << 16) /* I2C Addr: 0b'101xxxx */
|
|
|
|
static const struct i2c_device_id max732x_id[] = {
|
|
{ "max7319", GROUP_A(IO_8I) },
|
|
{ "max7320", GROUP_B(IO_8O) },
|
|
{ "max7321", GROUP_A(IO_8P) },
|
|
{ "max7322", GROUP_A(IO_4I4O) },
|
|
{ "max7323", GROUP_A(IO_4P4O) },
|
|
{ "max7324", GROUP_A(IO_8I) | GROUP_B(IO_8O) },
|
|
{ "max7325", GROUP_A(IO_8P) | GROUP_B(IO_8O) },
|
|
{ "max7326", GROUP_A(IO_4I4O) | GROUP_B(IO_8O) },
|
|
{ "max7327", GROUP_A(IO_4P4O) | GROUP_B(IO_8O) },
|
|
{ },
|
|
};
|
|
MODULE_DEVICE_TABLE(i2c, max732x_id);
|
|
|
|
struct max732x_chip {
|
|
struct gpio_chip gpio_chip;
|
|
|
|
struct i2c_client *client; /* "main" client */
|
|
struct i2c_client *client_dummy;
|
|
struct i2c_client *client_group_a;
|
|
struct i2c_client *client_group_b;
|
|
|
|
unsigned int mask_group_a;
|
|
unsigned int dir_input;
|
|
unsigned int dir_output;
|
|
|
|
struct mutex lock;
|
|
uint8_t reg_out[2];
|
|
};
|
|
|
|
static int max732x_write(struct max732x_chip *chip, int group_a, uint8_t val)
|
|
{
|
|
struct i2c_client *client;
|
|
int ret;
|
|
|
|
client = group_a ? chip->client_group_a : chip->client_group_b;
|
|
ret = i2c_smbus_write_byte(client, val);
|
|
if (ret < 0) {
|
|
dev_err(&client->dev, "failed writing\n");
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int max732x_read(struct max732x_chip *chip, int group_a, uint8_t *val)
|
|
{
|
|
struct i2c_client *client;
|
|
int ret;
|
|
|
|
client = group_a ? chip->client_group_a : chip->client_group_b;
|
|
ret = i2c_smbus_read_byte(client);
|
|
if (ret < 0) {
|
|
dev_err(&client->dev, "failed reading\n");
|
|
return ret;
|
|
}
|
|
|
|
*val = (uint8_t)ret;
|
|
return 0;
|
|
}
|
|
|
|
static inline int is_group_a(struct max732x_chip *chip, unsigned off)
|
|
{
|
|
return (1u << off) & chip->mask_group_a;
|
|
}
|
|
|
|
static int max732x_gpio_get_value(struct gpio_chip *gc, unsigned off)
|
|
{
|
|
struct max732x_chip *chip;
|
|
uint8_t reg_val;
|
|
int ret;
|
|
|
|
chip = container_of(gc, struct max732x_chip, gpio_chip);
|
|
|
|
ret = max732x_read(chip, is_group_a(chip, off), ®_val);
|
|
if (ret < 0)
|
|
return 0;
|
|
|
|
return reg_val & (1u << (off & 0x7));
|
|
}
|
|
|
|
static void max732x_gpio_set_value(struct gpio_chip *gc, unsigned off, int val)
|
|
{
|
|
struct max732x_chip *chip;
|
|
uint8_t reg_out, mask = 1u << (off & 0x7);
|
|
int ret;
|
|
|
|
chip = container_of(gc, struct max732x_chip, gpio_chip);
|
|
|
|
mutex_lock(&chip->lock);
|
|
|
|
reg_out = (off > 7) ? chip->reg_out[1] : chip->reg_out[0];
|
|
reg_out = (val) ? reg_out | mask : reg_out & ~mask;
|
|
|
|
ret = max732x_write(chip, is_group_a(chip, off), reg_out);
|
|
if (ret < 0)
|
|
goto out;
|
|
|
|
/* update the shadow register then */
|
|
if (off > 7)
|
|
chip->reg_out[1] = reg_out;
|
|
else
|
|
chip->reg_out[0] = reg_out;
|
|
out:
|
|
mutex_unlock(&chip->lock);
|
|
}
|
|
|
|
static int max732x_gpio_direction_input(struct gpio_chip *gc, unsigned off)
|
|
{
|
|
struct max732x_chip *chip;
|
|
unsigned int mask = 1u << off;
|
|
|
|
chip = container_of(gc, struct max732x_chip, gpio_chip);
|
|
|
|
if ((mask & chip->dir_input) == 0) {
|
|
dev_dbg(&chip->client->dev, "%s port %d is output only\n",
|
|
chip->client->name, off);
|
|
return -EACCES;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int max732x_gpio_direction_output(struct gpio_chip *gc,
|
|
unsigned off, int val)
|
|
{
|
|
struct max732x_chip *chip;
|
|
unsigned int mask = 1u << off;
|
|
|
|
chip = container_of(gc, struct max732x_chip, gpio_chip);
|
|
|
|
if ((mask & chip->dir_output) == 0) {
|
|
dev_dbg(&chip->client->dev, "%s port %d is input only\n",
|
|
chip->client->name, off);
|
|
return -EACCES;
|
|
}
|
|
|
|
max732x_gpio_set_value(gc, off, val);
|
|
return 0;
|
|
}
|
|
|
|
static int __devinit max732x_setup_gpio(struct max732x_chip *chip,
|
|
const struct i2c_device_id *id,
|
|
unsigned gpio_start)
|
|
{
|
|
struct gpio_chip *gc = &chip->gpio_chip;
|
|
uint32_t id_data = id->driver_data;
|
|
int i, port = 0;
|
|
|
|
for (i = 0; i < 16; i++, id_data >>= 2) {
|
|
unsigned int mask = 1 << port;
|
|
|
|
switch (id_data & 0x3) {
|
|
case PORT_OUTPUT:
|
|
chip->dir_output |= mask;
|
|
break;
|
|
case PORT_INPUT:
|
|
chip->dir_input |= mask;
|
|
break;
|
|
case PORT_OPENDRAIN:
|
|
chip->dir_output |= mask;
|
|
chip->dir_input |= mask;
|
|
break;
|
|
default:
|
|
continue;
|
|
}
|
|
|
|
if (i < 8)
|
|
chip->mask_group_a |= mask;
|
|
port++;
|
|
}
|
|
|
|
if (chip->dir_input)
|
|
gc->direction_input = max732x_gpio_direction_input;
|
|
if (chip->dir_output) {
|
|
gc->direction_output = max732x_gpio_direction_output;
|
|
gc->set = max732x_gpio_set_value;
|
|
}
|
|
gc->get = max732x_gpio_get_value;
|
|
gc->can_sleep = 1;
|
|
|
|
gc->base = gpio_start;
|
|
gc->ngpio = port;
|
|
gc->label = chip->client->name;
|
|
gc->owner = THIS_MODULE;
|
|
|
|
return port;
|
|
}
|
|
|
|
static int __devinit max732x_probe(struct i2c_client *client,
|
|
const struct i2c_device_id *id)
|
|
{
|
|
struct max732x_platform_data *pdata;
|
|
struct max732x_chip *chip;
|
|
struct i2c_client *c;
|
|
uint16_t addr_a, addr_b;
|
|
int ret, nr_port;
|
|
|
|
pdata = client->dev.platform_data;
|
|
if (pdata == NULL) {
|
|
dev_dbg(&client->dev, "no platform data\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
chip = kzalloc(sizeof(struct max732x_chip), GFP_KERNEL);
|
|
if (chip == NULL)
|
|
return -ENOMEM;
|
|
chip->client = client;
|
|
|
|
nr_port = max732x_setup_gpio(chip, id, pdata->gpio_base);
|
|
|
|
addr_a = (client->addr & 0x0f) | 0x60;
|
|
addr_b = (client->addr & 0x0f) | 0x50;
|
|
|
|
switch (client->addr & 0x70) {
|
|
case 0x60:
|
|
chip->client_group_a = client;
|
|
if (nr_port > 7) {
|
|
c = i2c_new_dummy(client->adapter, addr_b);
|
|
chip->client_group_b = chip->client_dummy = c;
|
|
}
|
|
break;
|
|
case 0x50:
|
|
chip->client_group_b = client;
|
|
if (nr_port > 7) {
|
|
c = i2c_new_dummy(client->adapter, addr_a);
|
|
chip->client_group_a = chip->client_dummy = c;
|
|
}
|
|
break;
|
|
default:
|
|
dev_err(&client->dev, "invalid I2C address specified %02x\n",
|
|
client->addr);
|
|
ret = -EINVAL;
|
|
goto out_failed;
|
|
}
|
|
|
|
mutex_init(&chip->lock);
|
|
|
|
max732x_read(chip, is_group_a(chip, 0), &chip->reg_out[0]);
|
|
if (nr_port > 7)
|
|
max732x_read(chip, is_group_a(chip, 8), &chip->reg_out[1]);
|
|
|
|
ret = gpiochip_add(&chip->gpio_chip);
|
|
if (ret)
|
|
goto out_failed;
|
|
|
|
if (pdata->setup) {
|
|
ret = pdata->setup(client, chip->gpio_chip.base,
|
|
chip->gpio_chip.ngpio, pdata->context);
|
|
if (ret < 0)
|
|
dev_warn(&client->dev, "setup failed, %d\n", ret);
|
|
}
|
|
|
|
i2c_set_clientdata(client, chip);
|
|
return 0;
|
|
|
|
out_failed:
|
|
kfree(chip);
|
|
return ret;
|
|
}
|
|
|
|
static int __devexit max732x_remove(struct i2c_client *client)
|
|
{
|
|
struct max732x_platform_data *pdata = client->dev.platform_data;
|
|
struct max732x_chip *chip = i2c_get_clientdata(client);
|
|
int ret;
|
|
|
|
if (pdata->teardown) {
|
|
ret = pdata->teardown(client, chip->gpio_chip.base,
|
|
chip->gpio_chip.ngpio, pdata->context);
|
|
if (ret < 0) {
|
|
dev_err(&client->dev, "%s failed, %d\n",
|
|
"teardown", ret);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
ret = gpiochip_remove(&chip->gpio_chip);
|
|
if (ret) {
|
|
dev_err(&client->dev, "%s failed, %d\n",
|
|
"gpiochip_remove()", ret);
|
|
return ret;
|
|
}
|
|
|
|
/* unregister any dummy i2c_client */
|
|
if (chip->client_dummy)
|
|
i2c_unregister_device(chip->client_dummy);
|
|
|
|
kfree(chip);
|
|
return 0;
|
|
}
|
|
|
|
static struct i2c_driver max732x_driver = {
|
|
.driver = {
|
|
.name = "max732x",
|
|
.owner = THIS_MODULE,
|
|
},
|
|
.probe = max732x_probe,
|
|
.remove = __devexit_p(max732x_remove),
|
|
.id_table = max732x_id,
|
|
};
|
|
|
|
static int __init max732x_init(void)
|
|
{
|
|
return i2c_add_driver(&max732x_driver);
|
|
}
|
|
/* register after i2c postcore initcall and before
|
|
* subsys initcalls that may rely on these GPIOs
|
|
*/
|
|
subsys_initcall(max732x_init);
|
|
|
|
static void __exit max732x_exit(void)
|
|
{
|
|
i2c_del_driver(&max732x_driver);
|
|
}
|
|
module_exit(max732x_exit);
|
|
|
|
MODULE_AUTHOR("Eric Miao <eric.miao@marvell.com>");
|
|
MODULE_DESCRIPTION("GPIO expander driver for MAX732X");
|
|
MODULE_LICENSE("GPL");
|