Minki/linux
1
0
Fork 1
mirror of https://github.com/torvalds/linux.git synced 2024-12-28 13:51:44 +00:00
Code Issues Packages Projects Releases Wiki Activity
eb2814bc60
linux/Documentation/devicetree/bindings/arm/cpus.yaml
Sugaya Taichi fd73403a48 dt-bindings: arm: Add SMP enable-method for Milbeaut 
This adds a compatible string "socionext,milbeaut-m10v-smp"
for Milbeaut M10V to the 32 bit ARM CPU device tree binding.

Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2019-03-01 15:18:26 +01:00

509 lines
14 KiB
YAML
Raw Blame History

# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/arm/cpus.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: ARM CPUs bindings
maintainers:
- Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
description: |+
The device tree allows to describe the layout of CPUs in a system through
the "cpus" node, which in turn contains a number of subnodes (ie "cpu")
defining properties for every cpu.
Bindings for CPU nodes follow the Devicetree Specification, available from:
https://www.devicetree.org/specifications/
with updates for 32-bit and 64-bit ARM systems provided in this document.
================================
Convention used in this document
================================
This document follows the conventions described in the Devicetree
Specification, with the addition:
- square brackets define bitfields, eg reg[7:0] value of the bitfield in
the reg property contained in bits 7 down to 0
=====================================
cpus and cpu node bindings definition
=====================================
The ARM architecture, in accordance with the Devicetree Specification,
requires the cpus and cpu nodes to be present and contain the properties
described below.
properties:
$nodename:
const: cpus
description: Container of cpu nodes
'#address-cells':
enum: [1, 2]
description: |
Definition depends on ARM architecture version and configuration:
On uniprocessor ARM architectures previous to v7
value must be 1, to enable a simple enumeration
scheme for processors that do not have a HW CPU
identification register.
On 32-bit ARM 11 MPcore, ARM v7 or later systems
value must be 1, that corresponds to CPUID/MPIDR
registers sizes.
On ARM v8 64-bit systems value should be set to 2,
that corresponds to the MPIDR_EL1 register size.
If MPIDR_EL1[63:32] value is equal to 0 on all CPUs
in the system, #address-cells can be set to 1, since
MPIDR_EL1[63:32] bits are not used for CPUs
identification.
'#size-cells':
const: 0
patternProperties:
'^cpu@[0-9a-f]+$':
properties:
device_type:
const: cpu
reg:
maxItems: 1
description: |
Usage and definition depend on ARM architecture version and
configuration:
On uniprocessor ARM architectures previous to v7
this property is required and must be set to 0.
On ARM 11 MPcore based systems this property is
required and matches the CPUID[11:0] register bits.
Bits [11:0] in the reg cell must be set to
bits [11:0] in CPU ID register.
All other bits in the reg cell must be set to 0.
On 32-bit ARM v7 or later systems this property is
required and matches the CPU MPIDR[23:0] register
bits.
Bits [23:0] in the reg cell must be set to
bits [23:0] in MPIDR.
All other bits in the reg cell must be set to 0.
On ARM v8 64-bit systems this property is required
and matches the MPIDR_EL1 register affinity bits.
* If cpus node's #address-cells property is set to 2
The first reg cell bits [7:0] must be set to
bits [39:32] of MPIDR_EL1.
The second reg cell bits [23:0] must be set to
bits [23:0] of MPIDR_EL1.
* If cpus node's #address-cells property is set to 1
The reg cell bits [23:0] must be set to bits [23:0]
of MPIDR_EL1.
All other bits in the reg cells must be set to 0.
compatible:
items:
- enum:
- arm,arm710t
- arm,arm720t
- arm,arm740t
- arm,arm7ej-s
- arm,arm7tdmi
- arm,arm7tdmi-s
- arm,arm9es
- arm,arm9ej-s
- arm,arm920t
- arm,arm922t
- arm,arm925
- arm,arm926e-s
- arm,arm926ej-s
- arm,arm940t
- arm,arm946e-s
- arm,arm966e-s
- arm,arm968e-s
- arm,arm9tdmi
- arm,arm1020e
- arm,arm1020t
- arm,arm1022e
- arm,arm1026ej-s
- arm,arm1136j-s
- arm,arm1136jf-s
- arm,arm1156t2-s
- arm,arm1156t2f-s
- arm,arm1176jzf
- arm,arm1176jz-s
- arm,arm1176jzf-s
- arm,arm11mpcore
- arm,armv8 # Only for s/w models
- arm,cortex-a5
- arm,cortex-a7
- arm,cortex-a8
- arm,cortex-a9
- arm,cortex-a12
- arm,cortex-a15
- arm,cortex-a17
- arm,cortex-a53
- arm,cortex-a57
- arm,cortex-a72
- arm,cortex-a73
- arm,cortex-m0
- arm,cortex-m0+
- arm,cortex-m1
- arm,cortex-m3
- arm,cortex-m4
- arm,cortex-r4
- arm,cortex-r5
- arm,cortex-r7
- brcm,brahma-b15
- brcm,brahma-b53
- brcm,vulcan
- cavium,thunder
- cavium,thunder2
- faraday,fa526
- intel,sa110
- intel,sa1100
- marvell,feroceon
- marvell,mohawk
- marvell,pj4a
- marvell,pj4b
- marvell,sheeva-v5
- marvell,sheeva-v7
- nvidia,tegra132-denver
- nvidia,tegra186-denver
- nvidia,tegra194-carmel
- qcom,krait
- qcom,kryo
- qcom,kryo385
- qcom,scorpion
enable-method:
allOf:
- $ref: '/schemas/types.yaml#/definitions/string'
- oneOf:
# On ARM v8 64-bit this property is required
- enum:
- psci
- spin-table
# On ARM 32-bit systems this property is optional
- enum:
- actions,s500-smp
- allwinner,sun6i-a31
- allwinner,sun8i-a23
- allwinner,sun9i-a80-smp
- allwinner,sun8i-a83t-smp
- amlogic,meson8-smp
- amlogic,meson8b-smp
- arm,realview-smp
- brcm,bcm11351-cpu-method
- brcm,bcm23550
- brcm,bcm2836-smp
- brcm,bcm63138
- brcm,bcm-nsp-smp
- brcm,brahma-b15
- marvell,armada-375-smp
- marvell,armada-380-smp
- marvell,armada-390-smp
- marvell,armada-xp-smp
- marvell,98dx3236-smp
- mediatek,mt6589-smp
- mediatek,mt81xx-tz-smp
- qcom,gcc-msm8660
- qcom,kpss-acc-v1
- qcom,kpss-acc-v2
- renesas,apmu
- renesas,r9a06g032-smp
- rockchip,rk3036-smp
- rockchip,rk3066-smp
- socionext,milbeaut-m10v-smp
- ste,dbx500-smp
cpu-release-addr:
$ref: '/schemas/types.yaml#/definitions/uint64'
description:
Required for systems that have an "enable-method"
property value of "spin-table".
On ARM v8 64-bit systems must be a two cell
property identifying a 64-bit zero-initialised
memory location.
cpu-idle-states:
$ref: '/schemas/types.yaml#/definitions/phandle-array'
description: |
List of phandles to idle state nodes supported
by this cpu (see ./idle-states.txt).
capacity-dmips-mhz:
$ref: '/schemas/types.yaml#/definitions/uint32'
description:
u32 value representing CPU capacity (see ./cpu-capacity.txt) in
DMIPS/MHz, relative to highest capacity-dmips-mhz
in the system.
dynamic-power-coefficient:
$ref: '/schemas/types.yaml#/definitions/uint32'
description:
A u32 value that represents the running time dynamic
power coefficient in units of uW/MHz/V^2. The
coefficient can either be calculated from power
measurements or derived by analysis.
The dynamic power consumption of the CPU is
proportional to the square of the Voltage (V) and
the clock frequency (f). The coefficient is used to
calculate the dynamic power as below -
Pdyn = dynamic-power-coefficient * V^2 * f
where voltage is in V, frequency is in MHz.
qcom,saw:
$ref: '/schemas/types.yaml#/definitions/phandle'
description: |
Specifies the SAW* node associated with this CPU.
Required for systems that have an "enable-method" property
value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2"
* arm/msm/qcom,saw2.txt
qcom,acc:
$ref: '/schemas/types.yaml#/definitions/phandle'
description: |
Specifies the ACC* node associated with this CPU.
Required for systems that have an "enable-method" property
value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2"
* arm/msm/qcom,kpss-acc.txt
rockchip,pmu:
$ref: '/schemas/types.yaml#/definitions/phandle'
description: |
Specifies the syscon node controlling the cpu core power domains.
Optional for systems that have an "enable-method"
property value of "rockchip,rk3066-smp"
While optional, it is the preferred way to get access to
the cpu-core power-domains.
required:
- device_type
- reg
- compatible
dependencies:
cpu-release-addr: [enable-method]
rockchip,pmu: [enable-method]
required:
- '#address-cells'
- '#size-cells'
examples:
- |
cpus {
#size-cells = <0>;
#address-cells = <1>;
cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x0>;
};
cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x1>;
};
cpu@100 {
device_type = "cpu";
compatible = "arm,cortex-a7";
reg = <0x100>;
};
cpu@101 {
device_type = "cpu";
compatible = "arm,cortex-a7";
reg = <0x101>;
};
};
- |
// Example 2 (Cortex-A8 uniprocessor 32-bit system):
cpus {
#size-cells = <0>;
#address-cells = <1>;
cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a8";
reg = <0x0>;
};
};
- |
// Example 3 (ARM 926EJ-S uniprocessor 32-bit system):
cpus {
#size-cells = <0>;
#address-cells = <1>;
cpu@0 {
device_type = "cpu";
compatible = "arm,arm926ej-s";
reg = <0x0>;
};
};
- |
// Example 4 (ARM Cortex-A57 64-bit system):
cpus {
#size-cells = <0>;
#address-cells = <2>;
cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x0 0x0>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x0 0x1>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@100 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x0 0x100>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@101 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x0 0x101>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@10000 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x0 0x10000>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@10001 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x0 0x10001>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@10100 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x0 0x10100>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@10101 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x0 0x10101>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@100000000 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x1 0x0>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@100000001 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x1 0x1>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@100000100 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x1 0x100>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@100000101 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x1 0x101>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@100010000 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x1 0x10000>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@100010001 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x1 0x10001>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@100010100 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x1 0x10100>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
cpu@100010101 {
device_type = "cpu";
compatible = "arm,cortex-a57";
reg = <0x1 0x10101>;
enable-method = "spin-table";
cpu-release-addr = <0 0x20000000>;
};
};
...
Reference in New Issue View Git Blame Copy Permalink