linux/init
Thomas Gleixner e7ff3a4763 x86/amd: Check for the C1E bug post ACPI subsystem init
AMD CPUs affected by the E400 erratum suffer from the issue that the
local APIC timer stops when the CPU goes into C1E. Unfortunately there
is no way to detect the affected CPUs on early boot. It's only possible
to determine the range of possibly affected CPUs from the family/model
range.

The actual decision whether to enter C1E and thus cause the bug is done
by the firmware and we need to detect that case late, after ACPI has
been initialized.

The current solution is to check in the idle routine whether the CPU is
affected by reading the MSR_K8_INT_PENDING_MSG MSR and checking for the
K8_INTP_C1E_ACTIVE_MASK bits. If one of the bits is set then the CPU is
affected and the system is switched into forced broadcast mode.

This is ineffective and on non-affected CPUs every entry to idle does
the extra RDMSR.

After doing some research it turns out that the bits are visible on the
boot CPU right after the ACPI subsystem is initialized in the early
boot process. So instead of polling for the bits in the idle loop, add
a detection function after acpi_subsystem_init() and check for the MSR
bits. If set, then the X86_BUG_AMD_APIC_C1E is set on the boot CPU and
the TSC is marked unstable when X86_FEATURE_NONSTOP_TSC is not set as it
will stop in C1E state as well.

The switch to broadcast mode cannot be done at this point because the
boot CPU still uses HPET as a clockevent device and the local APIC timer
is not yet calibrated and installed. The switch to broadcast mode on the
affected CPUs needs to be done when the local APIC timer is actually set
up.

This allows to cleanup the amd_e400_idle() function in the next step.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-4-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-12-09 21:23:21 +01:00
..
calibrate.c kernel: add calibration_delay_done() 2014-06-16 12:47:39 -06:00
do_mounts_initrd.c init/do_mounts: initrd_load() can be boolean 2016-01-20 17:09:18 -08:00
do_mounts_md.c
do_mounts_rd.c init, Documentation: Remove ramdisk_blocksize mentions 2015-12-26 05:22:00 -07:00
do_mounts.c init/do_mounts.c: add create_dev() failure log 2015-06-25 17:00:42 -07:00
do_mounts.h init/do_mounts: initrd_load() can be boolean 2016-01-20 17:09:18 -08:00
init_task.c sched/core: Allow putting thread_info into task_struct 2016-09-15 08:25:13 +02:00
initramfs.c kexec: split kexec_load syscall from kexec core code 2015-09-10 13:29:01 -07:00
Kconfig relay: Use irq_work instead of plain timer for deferred wakeup 2016-10-11 15:06:32 -07:00
main.c x86/amd: Check for the C1E bug post ACPI subsystem init 2016-12-09 21:23:21 +01:00
Makefile kbuild: allow archs to select link dead code/data elimination 2016-09-09 10:47:00 +02:00
noinitramfs.c
version.c copy address of proc_ns_ops into ns_common 2014-12-04 14:34:47 -05:00