mirror of
https://github.com/torvalds/linux.git
synced 2024-11-08 13:11:45 +00:00
7912825d8b
clk_get() used to return NULL or an errno value depending on whether a clkdev lookup failed or a clock wasn't found in the primary clock list. As these disjoint paths were unified and everything now is handled via clkdev lookups, the NULL case never makes it out of clk_get(). Update accordingly and always look to the errno value. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
126 lines
3.0 KiB
C
126 lines
3.0 KiB
C
/*
|
|
* ALPHAPROJECT AP-SH4AD-0A Support.
|
|
*
|
|
* Copyright (C) 2010 ALPHAPROJECT Co.,Ltd.
|
|
* Copyright (C) 2010 Matt Fleming
|
|
* Copyright (C) 2010 Paul Mundt
|
|
*
|
|
* This file is subject to the terms and conditions of the GNU General Public
|
|
* License. See the file "COPYING" in the main directory of this archive
|
|
* for more details.
|
|
*/
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/io.h>
|
|
#include <linux/smsc911x.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/clk.h>
|
|
#include <asm/machvec.h>
|
|
#include <asm/sizes.h>
|
|
|
|
static struct resource smsc911x_resources[] = {
|
|
[0] = {
|
|
.name = "smsc911x-memory",
|
|
.start = 0xA4000000,
|
|
.end = 0xA4000000 + SZ_256 - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
[1] = {
|
|
.name = "smsc911x-irq",
|
|
.start = evt2irq(0x200),
|
|
.end = evt2irq(0x200),
|
|
.flags = IORESOURCE_IRQ,
|
|
},
|
|
};
|
|
|
|
static struct smsc911x_platform_config smsc911x_config = {
|
|
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
|
|
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
|
|
.flags = SMSC911X_USE_16BIT,
|
|
.phy_interface = PHY_INTERFACE_MODE_MII,
|
|
};
|
|
|
|
static struct platform_device smsc911x_device = {
|
|
.name = "smsc911x",
|
|
.id = -1,
|
|
.num_resources = ARRAY_SIZE(smsc911x_resources),
|
|
.resource = smsc911x_resources,
|
|
.dev = {
|
|
.platform_data = &smsc911x_config,
|
|
},
|
|
};
|
|
|
|
static struct platform_device *apsh4ad0a_devices[] __initdata = {
|
|
&smsc911x_device,
|
|
};
|
|
|
|
static int __init apsh4ad0a_devices_setup(void)
|
|
{
|
|
return platform_add_devices(apsh4ad0a_devices,
|
|
ARRAY_SIZE(apsh4ad0a_devices));
|
|
}
|
|
device_initcall(apsh4ad0a_devices_setup);
|
|
|
|
static int apsh4ad0a_mode_pins(void)
|
|
{
|
|
int value = 0;
|
|
|
|
/* These are the factory default settings of SW1 and SW2.
|
|
* If you change these dip switches then you will need to
|
|
* adjust the values below as well.
|
|
*/
|
|
value |= MODE_PIN0; /* Clock Mode 3 */
|
|
value |= MODE_PIN1;
|
|
value &= ~MODE_PIN2;
|
|
value &= ~MODE_PIN3;
|
|
value &= ~MODE_PIN4; /* 16-bit Area0 bus width */
|
|
value |= MODE_PIN5;
|
|
value |= MODE_PIN6;
|
|
value |= MODE_PIN7; /* Normal mode */
|
|
value |= MODE_PIN8; /* Little Endian */
|
|
value |= MODE_PIN9; /* Crystal resonator */
|
|
value &= ~MODE_PIN10; /* 29-bit address mode */
|
|
value &= ~MODE_PIN11; /* PCI-E Root port */
|
|
value &= ~MODE_PIN12; /* 4 lane + 1 lane */
|
|
value |= MODE_PIN13; /* AUD Enable */
|
|
value &= ~MODE_PIN14; /* Normal Operation */
|
|
|
|
return value;
|
|
}
|
|
|
|
static int apsh4ad0a_clk_init(void)
|
|
{
|
|
struct clk *clk;
|
|
int ret;
|
|
|
|
clk = clk_get(NULL, "extal");
|
|
if (IS_ERR(clk))
|
|
return PTR_ERR(clk);
|
|
ret = clk_set_rate(clk, 33333000);
|
|
clk_put(clk);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/* Initialize the board */
|
|
static void __init apsh4ad0a_setup(char **cmdline_p)
|
|
{
|
|
pr_info("Alpha Project AP-SH4AD-0A support:\n");
|
|
}
|
|
|
|
static void __init apsh4ad0a_init_irq(void)
|
|
{
|
|
plat_irq_setup_pins(IRQ_MODE_IRQ3210);
|
|
}
|
|
|
|
/*
|
|
* The Machine Vector
|
|
*/
|
|
static struct sh_machine_vector mv_apsh4ad0a __initmv = {
|
|
.mv_name = "AP-SH4AD-0A",
|
|
.mv_setup = apsh4ad0a_setup,
|
|
.mv_mode_pins = apsh4ad0a_mode_pins,
|
|
.mv_clk_init = apsh4ad0a_clk_init,
|
|
.mv_init_irq = apsh4ad0a_init_irq,
|
|
};
|