Manjunath Hadli e13c692b1f ARM: davinci: vpif: move code to driver core header from platform ... Move vpif related definitions for capture and display drivers from dm646x platform header file to vpif_types.h inside the driver as these definitions are related to driver code rather than the platform or board. This enables reusing this IP across platforms. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>		2011-12-03 00:33:50 +05:30
..
aemif.h	davinci: add support for aemif timing configuration	2010-09-24 07:40:26 -07:00
asp.h	ASoC: davinci: let platform data define edma queue numbers	2010-07-20 09:57:20 +01:00
cdce949.h	davinci: add support for CDCE949 clock synthesizer	2010-02-04 13:29:58 -08:00
clock.h
common.h	Davinci: iotable based ioremap() interception	2010-05-13 10:05:31 -07:00
cp_intc.h	Davinci: aintc/cpintc - use ioremap()	2010-05-13 10:05:28 -07:00
cpufreq.h	davinci: DA850/OMAP-L138: avoid using separate initcall for initializing regulator	2009-11-25 10:21:37 -08:00
cpuidle.h	davinci: cpuidle: move mapping of DDR2 controller registers out of driver	2010-02-04 13:29:38 -08:00
cputype.h	Fix common misspellings	2011-03-31 11:26:23 -03:00
da8xx.h	davinci: da850: add support for SATA interface	2011-07-08 11:13:08 +05:30
ddr2.h	ARM: mach-davinci: remove mach/memory.h	2011-10-13 12:49:47 -04:00
debug-macro.S	ARM: mach-davinci: clean up debug-macro.S	2011-09-26 10:11:28 -04:00
dm355.h	DaVinci: move AEMIF #define's to the proper headers	2010-05-06 15:02:06 -07:00
dm365.h	davinci: cleanup mdio arch code and switch to phy_id	2010-09-24 07:40:30 -07:00
dm644x.h	davinci: cleanup mdio arch code and switch to phy_id	2010-09-24 07:40:30 -07:00
dm646x.h	ARM: davinci: vpif: move code to driver core header from platform	2011-12-03 00:33:50 +05:30
edma.h	davinci: remove unused DA830_edma_ch enum	2011-03-11 10:48:28 -08:00
entry-macro.S	ARM: entry: remove unused irq_prio_table macro	2011-06-28 10:34:58 +01:00
gpio-davinci.h	ARM: 7040/1: mach-davinci: break out GPIO driver specifics	2011-08-22 09:12:56 +01:00
gpio.h	ARM: 7142/1: davinci: mark GPIO implementation complex	2011-11-05 19:09:47 +00:00
hardware.h	davinci: move DM64XX_VDD3P3V_PWDN to devices.c	2011-05-23 22:18:26 +05:30
i2c.h	Merge branch 'for-next' into for-linus	2010-03-08 16:55:37 +01:00
io.h	ARM: io: make iounmap() a simple macro	2010-12-08 13:57:04 +00:00
irqs.h	Davinci: tnetv107x IRQ definitions	2010-05-06 15:02:05 -07:00
keyscan.h	Input: davinci_keyscan - add device_enable method to platform data	2010-01-06 00:17:11 -08:00
mmc.h	mmc: davinci: Add support for set_power callback	2011-09-17 15:53:23 +05:30
mux.h	ARM: davinci: DA850: Add GPIO pinmux configuration for wl1271	2011-09-17 15:53:22 +05:30
nand.h	mtd: nand: rename NAND_USE_FLASH_BBT	2011-09-11 15:01:56 +03:00
pm.h	davinci: add power management support	2010-02-04 13:29:55 -08:00
psc.h	ARM: davinci: correct MDSTAT_STATE_MASK	2011-09-07 14:23:02 +05:30
serial.h	ARM: mach-davinci: make DAVINCI_UART_INFO into a relative offset	2011-09-26 10:11:27 -04:00
spi.h	davinci: spi: move event queue parameter to platform data	2011-02-28 14:53:29 -08:00
sram.h	davinci: add SRAM allocator	2009-05-28 15:18:13 -07:00
system.h	Davinci: watchdog reset separation across socs	2010-05-06 15:02:09 -07:00
time.h	davinci: Add watchdog base address flexibility	2009-05-26 08:20:31 -07:00
timex.h	davinci: explain CLOCK_TICK_RATE of 27MHz in include/mach/timex.h	2010-02-04 13:29:41 -08:00
tnetv107x.h	davinci: add tnetv107x ssp platform device	2011-03-15 08:17:22 -07:00
uncompress.h	ARM: mach-davinci: make DAVINCI_UART_INFO into a relative offset	2011-09-26 10:11:27 -04:00
usb.h	DaVinci: rename setup_usb() to davinci_setup_usb()	2009-11-25 10:21:33 -08:00
vmalloc.h	davinci: Move IO device mapping macros from io.h to hardware.h	2009-08-26 10:57:01 +03:00