mirror of
https://github.com/torvalds/linux.git
synced 2024-12-17 16:43:08 +00:00
b9a3899d59
Hardware errors on the Blackfin architecture are queued by nature of the hardware design. Things that could generate a hardware level queue up at the system interface and might not process until much later, at which point the system would send a notification back to the core. As such, it is possible for user space code to do something that would trigger a hardware error, but have it delay long enough for the process context to switch. So when the hardware error does signal, we mistakenly evaluate it as a different process or as kernel context and panic (erp!). This makes it pretty difficult to find the offending context. But wait, there is good news somewhere. By forcing a SSYNC in the interrupt entry, we force all pending queues at the system level to be processed and all hardware errors to be signaled. Then we check the current interrupt state to see if the hardware error is now signaled. If so, we re-queue the current interrupt and return thus allowing the higher priority hardware error interrupt to process properly. Since we haven't done any other context processing yet, the right context will be selected and killed. There is still the possibility that the exact offending instruction will be unknown, but at least we'll have a much better idea of where to look. The downside of course is that this causes system-wide syncs at every interrupt point which results in significant performance degradation. Since this situation should not occur in any properly configured system (as hardware errors are triggered by things like bad pointers), make it a debug configuration option and disable it by default. Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
159 lines
4.7 KiB
C
159 lines
4.7 KiB
C
#ifndef __BFIN_ENTRY_H
|
|
#define __BFIN_ENTRY_H
|
|
|
|
#include <asm/setup.h>
|
|
#include <asm/page.h>
|
|
|
|
#ifdef __ASSEMBLY__
|
|
|
|
#define LFLUSH_I_AND_D 0x00000808
|
|
#define LSIGTRAP 5
|
|
|
|
/* process bits for task_struct.flags */
|
|
#define PF_TRACESYS_OFF 3
|
|
#define PF_TRACESYS_BIT 5
|
|
#define PF_PTRACED_OFF 3
|
|
#define PF_PTRACED_BIT 4
|
|
#define PF_DTRACE_OFF 1
|
|
#define PF_DTRACE_BIT 5
|
|
|
|
/*
|
|
* NOTE! The single-stepping code assumes that all interrupt handlers
|
|
* start by saving SYSCFG on the stack with their first instruction.
|
|
*/
|
|
|
|
/* This one is used for exceptions, emulation, and NMI. It doesn't push
|
|
RETI and doesn't do cli. */
|
|
#define SAVE_ALL_SYS save_context_no_interrupts
|
|
/* This is used for all normal interrupts. It saves a minimum of registers
|
|
to the stack, loads the IRQ number, and jumps to common code. */
|
|
#ifdef CONFIG_IPIPE
|
|
# define LOAD_IPIPE_IPEND \
|
|
P0.l = lo(IPEND); \
|
|
P0.h = hi(IPEND); \
|
|
R1 = [P0];
|
|
#else
|
|
# define LOAD_IPIPE_IPEND
|
|
#endif
|
|
|
|
#ifndef CONFIG_EXACT_HWERR
|
|
/* As a debugging aid - we save IPEND when DEBUG_KERNEL is on,
|
|
* otherwise it is a waste of cycles.
|
|
*/
|
|
# ifndef CONFIG_DEBUG_KERNEL
|
|
#define INTERRUPT_ENTRY(N) \
|
|
[--sp] = SYSCFG; \
|
|
[--sp] = P0; /*orig_p0*/ \
|
|
[--sp] = R0; /*orig_r0*/ \
|
|
[--sp] = (R7:0,P5:0); \
|
|
R0 = (N); \
|
|
LOAD_IPIPE_IPEND \
|
|
jump __common_int_entry;
|
|
# else /* CONFIG_DEBUG_KERNEL */
|
|
#define INTERRUPT_ENTRY(N) \
|
|
[--sp] = SYSCFG; \
|
|
[--sp] = P0; /*orig_p0*/ \
|
|
[--sp] = R0; /*orig_r0*/ \
|
|
[--sp] = (R7:0,P5:0); \
|
|
p0.l = lo(IPEND); \
|
|
p0.h = hi(IPEND); \
|
|
r1 = [p0]; \
|
|
R0 = (N); \
|
|
LOAD_IPIPE_IPEND \
|
|
jump __common_int_entry;
|
|
# endif /* CONFIG_DEBUG_KERNEL */
|
|
|
|
/* For timer interrupts, we need to save IPEND, since the user_mode
|
|
*macro accesses it to determine where to account time.
|
|
*/
|
|
#define TIMER_INTERRUPT_ENTRY(N) \
|
|
[--sp] = SYSCFG; \
|
|
[--sp] = P0; /*orig_p0*/ \
|
|
[--sp] = R0; /*orig_r0*/ \
|
|
[--sp] = (R7:0,P5:0); \
|
|
p0.l = lo(IPEND); \
|
|
p0.h = hi(IPEND); \
|
|
r1 = [p0]; \
|
|
R0 = (N); \
|
|
jump __common_int_entry;
|
|
#else /* CONFIG_EXACT_HWERR is defined */
|
|
|
|
/* if we want hardware error to be exact, we need to do a SSYNC (which forces
|
|
* read/writes to complete to the memory controllers), and check to see that
|
|
* caused a pending HW error condition. If so, we assume it was caused by user
|
|
* space, by setting the same interrupt that we are in (so it goes off again)
|
|
* and context restore, and a RTI (without servicing anything). This should
|
|
* cause the pending HWERR to fire, and when that is done, this interrupt will
|
|
* be re-serviced properly.
|
|
* As you can see by the code - we actually need to do two SSYNCS - one to
|
|
* make sure the read/writes complete, and another to make sure the hardware
|
|
* error is recognized by the core.
|
|
*/
|
|
#define INTERRUPT_ENTRY(N) \
|
|
SSYNC; \
|
|
SSYNC; \
|
|
[--sp] = SYSCFG; \
|
|
[--sp] = P0; /*orig_p0*/ \
|
|
[--sp] = R0; /*orig_r0*/ \
|
|
[--sp] = (R7:0,P5:0); \
|
|
R1 = ASTAT; \
|
|
P0.L = LO(ILAT); \
|
|
P0.H = HI(ILAT); \
|
|
R0 = [P0]; \
|
|
CC = BITTST(R0, EVT_IVHW_P); \
|
|
IF CC JUMP 1f; \
|
|
ASTAT = R1; \
|
|
p0.l = lo(IPEND); \
|
|
p0.h = hi(IPEND); \
|
|
r1 = [p0]; \
|
|
R0 = (N); \
|
|
LOAD_IPIPE_IPEND \
|
|
jump __common_int_entry; \
|
|
1: ASTAT = R1; \
|
|
RAISE N; \
|
|
(R7:0, P5:0) = [SP++]; \
|
|
SP += 0x8; \
|
|
SYSCFG = [SP++]; \
|
|
CSYNC; \
|
|
RTI;
|
|
|
|
#define TIMER_INTERRUPT_ENTRY(N) \
|
|
SSYNC; \
|
|
SSYNC; \
|
|
[--sp] = SYSCFG; \
|
|
[--sp] = P0; /*orig_p0*/ \
|
|
[--sp] = R0; /*orig_r0*/ \
|
|
[--sp] = (R7:0,P5:0); \
|
|
R1 = ASTAT; \
|
|
P0.L = LO(ILAT); \
|
|
P0.H = HI(ILAT); \
|
|
R0 = [P0]; \
|
|
CC = BITTST(R0, EVT_IVHW_P); \
|
|
IF CC JUMP 1f; \
|
|
ASTAT = R1; \
|
|
p0.l = lo(IPEND); \
|
|
p0.h = hi(IPEND); \
|
|
r1 = [p0]; \
|
|
R0 = (N); \
|
|
jump __common_int_entry; \
|
|
1: ASTAT = R1; \
|
|
RAISE N; \
|
|
(R7:0, P5:0) = [SP++]; \
|
|
SP += 0x8; \
|
|
SYSCFG = [SP++]; \
|
|
CSYNC; \
|
|
RTI;
|
|
#endif /* CONFIG_EXACT_HWERR */
|
|
|
|
/* This one pushes RETI without using CLI. Interrupts are enabled. */
|
|
#define SAVE_CONTEXT_SYSCALL save_context_syscall
|
|
#define SAVE_CONTEXT save_context_with_interrupts
|
|
#define SAVE_CONTEXT_CPLB save_context_cplb
|
|
|
|
#define RESTORE_ALL_SYS restore_context_no_interrupts
|
|
#define RESTORE_CONTEXT restore_context_with_interrupts
|
|
#define RESTORE_CONTEXT_CPLB restore_context_cplb
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BFIN_ENTRY_H */
|