mirror of
https://github.com/torvalds/linux.git
synced 2024-12-16 16:12:52 +00:00
6bef0b6747
All UBI needs is to make sure we stacktraces when UBI debugging is enabled. It is enough to select KALLSYMS for this, KALLSYMS_ALL is not necessary. And the current Kconfig line we have: select KALLSYMS_ALL if KALLSYMS && DEBUG_KERNEL is just too complex to be sane and right. But this "if" part there is needed to prevent "unmet direct dependency" warnings, because KALLSYMS_ALL depends on KALLSYMS and DEBUG_KERNEL, so we cannot just select KALLSYMS_ALL. Anyway, this feels messy, and we do not seem to really need KALLSYMS_ALL, so select KALLSYMS instead. Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
64 lines
2.5 KiB
Plaintext
64 lines
2.5 KiB
Plaintext
menuconfig MTD_UBI
|
|
tristate "Enable UBI - Unsorted block images"
|
|
select CRC32
|
|
help
|
|
UBI is a software layer above MTD layer which admits of LVM-like
|
|
logical volumes on top of MTD devices, hides some complexities of
|
|
flash chips like wear and bad blocks and provides some other useful
|
|
capabilities. Please, consult the MTD web site for more details
|
|
(www.linux-mtd.infradead.org).
|
|
|
|
if MTD_UBI
|
|
|
|
config MTD_UBI_WL_THRESHOLD
|
|
int "UBI wear-leveling threshold"
|
|
default 4096
|
|
range 2 65536
|
|
help
|
|
This parameter defines the maximum difference between the highest
|
|
erase counter value and the lowest erase counter value of eraseblocks
|
|
of UBI devices. When this threshold is exceeded, UBI starts performing
|
|
wear leveling by means of moving data from eraseblock with low erase
|
|
counter to eraseblocks with high erase counter.
|
|
|
|
The default value should be OK for SLC NAND flashes, NOR flashes and
|
|
other flashes which have eraseblock life-cycle 100000 or more.
|
|
However, in case of MLC NAND flashes which typically have eraseblock
|
|
life-cycle less than 10000, the threshold should be lessened (e.g.,
|
|
to 128 or 256, although it does not have to be power of 2).
|
|
|
|
config MTD_UBI_BEB_RESERVE
|
|
int "Percentage of reserved eraseblocks for bad eraseblocks handling"
|
|
default 1
|
|
range 0 25
|
|
help
|
|
If the MTD device admits of bad eraseblocks (e.g. NAND flash), UBI
|
|
reserves some amount of physical eraseblocks to handle new bad
|
|
eraseblocks. For example, if a flash physical eraseblock becomes bad,
|
|
UBI uses these reserved physical eraseblocks to relocate the bad one.
|
|
This option specifies how many physical eraseblocks will be reserved
|
|
for bad eraseblock handling (percents of total number of good flash
|
|
eraseblocks). If the underlying flash does not admit of bad
|
|
eraseblocks (e.g. NOR flash), this value is ignored and nothing is
|
|
reserved. Leave the default value if unsure.
|
|
|
|
config MTD_UBI_GLUEBI
|
|
tristate "MTD devices emulation driver (gluebi)"
|
|
help
|
|
This option enables gluebi - an additional driver which emulates MTD
|
|
devices on top of UBI volumes: for each UBI volumes an MTD device is
|
|
created, and all I/O to this MTD device is redirected to the UBI
|
|
volume. This is handy to make MTD-oriented software (like JFFS2)
|
|
work on top of UBI. Do not enable this unless you use legacy
|
|
software.
|
|
|
|
config MTD_UBI_DEBUG
|
|
bool "UBI debugging"
|
|
depends on SYSFS
|
|
select DEBUG_FS
|
|
select KALLSYMS
|
|
help
|
|
This option enables UBI debugging.
|
|
|
|
endif # MTD_UBI
|