mirror of
https://github.com/torvalds/linux.git
synced 2024-12-26 21:02:19 +00:00
936516bfb3
Acked-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
127 lines
3.4 KiB
Plaintext
127 lines
3.4 KiB
Plaintext
* STM32 GPIO and Pin Mux/Config controller
|
|
|
|
STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware
|
|
controller. It controls the input/output settings on the available pins and
|
|
also provides ability to multiplex and configure the output of various on-chip
|
|
controllers onto these pads.
|
|
|
|
Pin controller node:
|
|
Required properies:
|
|
- compatible: value should be one of the following:
|
|
(a) "st,stm32f429-pinctrl"
|
|
- #address-cells: The value of this property must be 1
|
|
- #size-cells : The value of this property must be 1
|
|
- ranges : defines mapping between pin controller node (parent) to
|
|
gpio-bank node (children).
|
|
- pins-are-numbered: Specify the subnodes are using numbered pinmux to
|
|
specify pins.
|
|
|
|
GPIO controller/bank node:
|
|
Required properties:
|
|
- gpio-controller : Indicates this device is a GPIO controller
|
|
- #gpio-cells : Should be two.
|
|
The first cell is the pin number
|
|
The second one is the polarity:
|
|
- 0 for active high
|
|
- 1 for active low
|
|
- reg : The gpio address range, relative to the pinctrl range
|
|
- clocks : clock that drives this bank
|
|
- st,bank-name : Should be a name string for this bank as specified in
|
|
the datasheet
|
|
|
|
Optional properties:
|
|
- reset: : Reference to the reset controller
|
|
|
|
Example:
|
|
#include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
|
|
...
|
|
|
|
pin-controller {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "st,stm32f429-pinctrl";
|
|
ranges = <0 0x40020000 0x3000>;
|
|
pins-are-numbered;
|
|
|
|
gpioa: gpio@40020000 {
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
reg = <0x0 0x400>;
|
|
resets = <&reset_ahb1 0>;
|
|
st,bank-name = "GPIOA";
|
|
};
|
|
...
|
|
pin-functions nodes follow...
|
|
};
|
|
|
|
Contents of function subnode node:
|
|
----------------------------------
|
|
Subnode format
|
|
A pinctrl node should contain at least one subnode representing the
|
|
pinctrl group available on the machine. Each subnode will list the
|
|
pins it needs, and how they should be configured, with regard to muxer
|
|
configuration, pullups, drive, output high/low and output speed.
|
|
|
|
node {
|
|
pinmux = <PIN_NUMBER_PINMUX>;
|
|
GENERIC_PINCONFIG;
|
|
};
|
|
|
|
Required properties:
|
|
- pinmux: integer array, represents gpio pin number and mux setting.
|
|
Supported pin number and mux varies for different SoCs, and are defined in
|
|
dt-bindings/pinctrl/<soc>-pinfunc.h directly.
|
|
These defines are calculated as:
|
|
((port * 16 + line) << 8) | function
|
|
With:
|
|
- port: The gpio port index (PA = 0, PB = 1, ..., PK = 11)
|
|
- line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
|
|
- function: The function number, can be:
|
|
* 0 : GPIO
|
|
* 1 : Alternate Function 0
|
|
* 2 : Alternate Function 1
|
|
* 3 : Alternate Function 2
|
|
* ...
|
|
* 16 : Alternate Function 15
|
|
* 17 : Analog
|
|
|
|
Optional properties:
|
|
- GENERIC_PINCONFIG: is the generic pinconfig options to use.
|
|
Available options are:
|
|
- bias-disable,
|
|
- bias-pull-down,
|
|
- bias-pull-up,
|
|
- drive-push-pull,
|
|
- drive-open-drain,
|
|
- output-low
|
|
- output-high
|
|
- slew-rate = <x>, with x being:
|
|
< 0 > : Low speed
|
|
< 1 > : Medium speed
|
|
< 2 > : Fast speed
|
|
< 3 > : High speed
|
|
|
|
Example:
|
|
|
|
pin-controller {
|
|
...
|
|
usart1_pins_a: usart1@0 {
|
|
pins1 {
|
|
pinmux = <STM32F429_PA9_FUNC_USART1_TX>;
|
|
bias-disable;
|
|
drive-push-pull;
|
|
slew-rate = <0>;
|
|
};
|
|
pins2 {
|
|
pinmux = <STM32F429_PA10_FUNC_USART1_RX>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usart1 {
|
|
pinctrl-0 = <&usart1_pins_a>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|