mirror of
https://github.com/torvalds/linux.git
synced 2024-12-20 18:11:47 +00:00
a7b3bf55e7
As the binding for slew-rate is under discussion and seems to need more tought it will get removed for now, so it doesn't get an offical release. Therefore remove it again from the only current user, tz1090. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
228 lines
8.6 KiB
Plaintext
228 lines
8.6 KiB
Plaintext
ImgTec TZ1090 pin controller
|
|
|
|
Required properties:
|
|
- compatible: "img,tz1090-pinctrl"
|
|
- reg: Should contain the register physical address and length of the pad
|
|
configuration registers (CR_PADS_* and CR_IF_CTL0).
|
|
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
|
common pinctrl bindings used by client devices, including the meaning of the
|
|
phrase "pin configuration node".
|
|
|
|
TZ1090's pin configuration nodes act as a container for an abitrary number of
|
|
subnodes. Each of these subnodes represents some desired configuration for a
|
|
pin, a group, or a list of pins or groups. This configuration can include the
|
|
mux function to select on those pin(s)/group(s), and various pin configuration
|
|
parameters, such as pull-up, drive strength, etc.
|
|
|
|
The name of each subnode is not important; all subnodes should be enumerated
|
|
and processed purely based on their content.
|
|
|
|
Each subnode only affects those parameters that are explicitly listed. In
|
|
other words, a subnode that lists a mux function but no pin configuration
|
|
parameters implies no information about any pin configuration parameters.
|
|
Similarly, a pin subnode that describes a pullup parameter implies no
|
|
information about e.g. the mux function. For this reason, even seemingly boolean
|
|
values are actually tristates in this binding: unspecified, off, or on.
|
|
Unspecified is represented as an absent property, and off/on are represented as
|
|
integer values 0 and 1.
|
|
|
|
Required subnode-properties:
|
|
- tz1090,pins : An array of strings. Each string contains the name of a pin or
|
|
group. Valid values for these names are listed below.
|
|
|
|
Optional subnode-properties:
|
|
- tz1090,function: A string containing the name of the function to mux to the
|
|
pin or group. Valid values for function names are listed below, including
|
|
which pingroups can be muxed to them.
|
|
- supported generic pinconfig properties (for further details see
|
|
Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt):
|
|
- bias-disable
|
|
- bias-high-impedance
|
|
- bias-bus-hold
|
|
- bias-pull-up
|
|
- bias-pull-down
|
|
- input-schmitt-enable
|
|
- input-schmitt-disable
|
|
- drive-strength: Integer, control drive strength of pins in mA.
|
|
2: 2mA
|
|
4: 4mA
|
|
8: 8mA
|
|
12: 12mA
|
|
|
|
|
|
Note that many of these properties are only valid for certain specific pins
|
|
or groups. See the TZ1090 TRM for complete details regarding which groups
|
|
support which functionality. The Linux pinctrl driver may also be a useful
|
|
reference.
|
|
|
|
Valid values for pin and group names are:
|
|
|
|
gpio pins:
|
|
|
|
These all support bias-high-impediance, bias-pull-up, bias-pull-down, and
|
|
bias-bus-hold (which can also be provided to any of the groups below to set
|
|
it for all pins in that group).
|
|
|
|
They also all support the some form of muxing. Any pins which are contained
|
|
in one of the mux groups (see below) can be muxed only to the functions
|
|
supported by the mux group. All other pins can be muxed to the "perip"
|
|
function which which enables them with their intended peripheral.
|
|
|
|
Different pins in the same mux group cannot be muxed to different functions,
|
|
however it is possible to mux only a subset of the pins in a mux group to a
|
|
particular function and leave the remaining pins unmuxed. This is useful if
|
|
the board connects certain pins in a group to other devices to be controlled
|
|
by GPIO, and you don't want the usual peripheral to have any control of the
|
|
pin.
|
|
|
|
ant_sel0, ant_sel1, gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7,
|
|
i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, i2s_lrclk_out,
|
|
i2s_mclk, pa_on, pdm_a, pdm_b, pdm_c, pdm_d, pll_on, rx_hp, rx_on,
|
|
scb0_sclk, scb0_sdat, scb1_sclk, scb1_sdat, scb2_sclk, scb2_sdat, sdh_cd,
|
|
sdh_clk_in, sdh_wp, sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
|
|
spi0_cs0, spi0_cs1, spi0_cs2, spi0_din, spi0_dout, spi0_mclk, spi1_cs0,
|
|
spi1_cs1, spi1_cs2, spi1_din, spi1_dout, spi1_mclk, tft_blank_ls, tft_blue0,
|
|
tft_blue1, tft_blue2, tft_blue3, tft_blue4, tft_blue5, tft_blue6, tft_blue7,
|
|
tft_green0, tft_green1, tft_green2, tft_green3, tft_green4, tft_green5,
|
|
tft_green6, tft_green7, tft_hsync_nr, tft_panelclk, tft_pwrsave, tft_red0,
|
|
tft_red1, tft_red2, tft_red3, tft_red4, tft_red5, tft_red6, tft_red7,
|
|
tft_vd12acb, tft_vdden_gd, tft_vsync_ns, tx_on, uart0_cts, uart0_rts,
|
|
uart0_rxd, uart0_txd, uart1_rxd, uart1_txd.
|
|
|
|
bias-high-impediance: supported.
|
|
bias-pull-up: supported.
|
|
bias-pull-down: supported.
|
|
bias-bus-hold: supported.
|
|
function: perip or those supported by pin's mux group.
|
|
|
|
other pins:
|
|
|
|
These other pins are part of various pin groups below, but can't be
|
|
controlled as GPIOs. They do however support bias-high-impediance,
|
|
bias-pull-up, bias-pull-down, and bias-bus-hold (which can also be provided
|
|
to any of the groups below to set it for all pins in that group).
|
|
|
|
clk_out0, clk_out1, tck, tdi, tdo, tms, trst.
|
|
|
|
bias-high-impediance: supported.
|
|
bias-pull-up: supported.
|
|
bias-pull-down: supported.
|
|
bias-bus-hold: supported.
|
|
|
|
mux groups:
|
|
|
|
These all support function, and some support drive configs.
|
|
|
|
afe
|
|
pins: tx_on, rx_on, pll_on, pa_on, rx_hp, ant_sel0,
|
|
ant_sel1, gain0, gain1, gain2, gain3, gain4,
|
|
gain5, gain6, gain7.
|
|
function: afe, ts_out_0.
|
|
input-schmitt-enable: supported.
|
|
input-schmitt-disable: supported.
|
|
drive-strength: supported.
|
|
pdm_d
|
|
pins: pdm_d.
|
|
function: pdm_dac, usb_vbus.
|
|
sdh
|
|
pins: sdh_cd, sdh_wp, sdh_clk_in.
|
|
function: sdh, sdio.
|
|
sdio
|
|
pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2,
|
|
sdio_d3.
|
|
function: sdio, sdh.
|
|
spi1_cs2
|
|
pins: spi1_cs2.
|
|
function: spi1_cs2, usb_vbus.
|
|
tft
|
|
pins: tft_red0, tft_red1, tft_red2, tft_red3,
|
|
tft_red4, tft_red5, tft_red6, tft_red7,
|
|
tft_green0, tft_green1, tft_green2, tft_green3,
|
|
tft_green4, tft_green5, tft_green6, tft_green7,
|
|
tft_blue0, tft_blue1, tft_blue2, tft_blue3,
|
|
tft_blue4, tft_blue5, tft_blue6, tft_blue7,
|
|
tft_vdden_gd, tft_panelclk, tft_blank_ls,
|
|
tft_vsync_ns, tft_hsync_nr, tft_vd12acb,
|
|
tft_pwrsave.
|
|
function: tft, ext_dac, not_iqadc_stb, iqdac_stb, ts_out_1,
|
|
lcd_trace, phy_ringosc.
|
|
input-schmitt-enable: supported.
|
|
input-schmitt-disable: supported.
|
|
drive-strength: supported.
|
|
|
|
drive groups:
|
|
|
|
These all support input-schmitt-enable, input-schmitt-disable,
|
|
and drive-strength.
|
|
|
|
jtag
|
|
pins: tck, trst, tdi, tdo, tms.
|
|
scb1
|
|
pins: scb1_sdat, scb1_sclk.
|
|
scb2
|
|
pins: scb2_sdat, scb2_sclk.
|
|
spi0
|
|
pins: spi0_mclk, spi0_cs0, spi0_cs1, spi0_cs2, spi0_dout, spi0_din.
|
|
spi1
|
|
pins: spi1_mclk, spi1_cs0, spi1_cs1, spi1_cs2, spi1_dout, spi1_din.
|
|
uart
|
|
pins: uart0_txd, uart0_rxd, uart0_rts, uart0_cts,
|
|
uart1_txd, uart1_rxd.
|
|
drive_i2s
|
|
pins: clk_out1, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
|
|
i2s_lrclk_out, i2s_bclk_out, i2s_mclk.
|
|
drive_pdm
|
|
pins: clk_out0, pdm_b, pdm_a.
|
|
drive_scb0
|
|
pins: scb0_sclk, scb0_sdat, pdm_d, pdm_c.
|
|
drive_sdio
|
|
pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
|
|
sdh_wp, sdh_cd, sdh_clk_in.
|
|
|
|
convenience groups:
|
|
|
|
These are just convenient groupings of pins and don't support any drive
|
|
configs.
|
|
|
|
uart0
|
|
pins: uart0_cts, uart0_rts, uart0_rxd, uart0_txd.
|
|
uart1
|
|
pins: uart1_rxd, uart1_txd.
|
|
scb0
|
|
pins: scb0_sclk, scb0_sdat.
|
|
i2s
|
|
pins: i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
|
|
i2s_lrclk_out, i2s_mclk.
|
|
|
|
Example:
|
|
|
|
pinctrl: pinctrl@02005800 {
|
|
#gpio-range-cells = <3>;
|
|
compatible = "img,tz1090-pinctrl";
|
|
reg = <0x02005800 0xe4>;
|
|
};
|
|
|
|
Example board file extract:
|
|
|
|
&pinctrl {
|
|
uart0_default: uart0 {
|
|
uart0_cfg {
|
|
tz1090,pins = "uart0_rxd",
|
|
"uart0_txd";
|
|
tz1090,function = "perip";
|
|
};
|
|
};
|
|
tft_default: tft {
|
|
tft_cfg {
|
|
tz1090,pins = "tft";
|
|
tz1090,function = "tft";
|
|
};
|
|
};
|
|
};
|
|
|
|
uart@02004b00 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_default>;
|
|
};
|