mirror of
https://github.com/torvalds/linux.git
synced 2024-12-24 11:51:27 +00:00
6f98f545b0
apq8016-sbc board is using Dual SPDT USB Switch (TC7USB40MU), witch is controlled by GPIO to de/multiplex D+/D- USB lines to USB2513B Hub and uB connector. Add support for this. Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
111 lines
4.2 KiB
Plaintext
111 lines
4.2 KiB
Plaintext
MSM SoC HSUSB controllers
|
|
|
|
EHCI
|
|
|
|
Required properties:
|
|
- compatible: Should contain "qcom,ehci-host"
|
|
- regs: offset and length of the register set in the memory map
|
|
- usb-phy: phandle for the PHY device
|
|
|
|
Example EHCI controller device node:
|
|
|
|
ehci: ehci@f9a55000 {
|
|
compatible = "qcom,ehci-host";
|
|
reg = <0xf9a55000 0x400>;
|
|
usb-phy = <&usb_otg>;
|
|
};
|
|
|
|
USB PHY with optional OTG:
|
|
|
|
Required properties:
|
|
- compatible: Should contain:
|
|
"qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY
|
|
"qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY
|
|
|
|
- regs: Offset and length of the register set in the memory map
|
|
- interrupts: interrupt-specifier for the OTG interrupt.
|
|
|
|
- clocks: A list of phandle + clock-specifier pairs for the
|
|
clocks listed in clock-names
|
|
- clock-names: Should contain the following:
|
|
"phy" USB PHY reference clock
|
|
"core" Protocol engine clock
|
|
"iface" Interface bus clock
|
|
"alt_core" Protocol engine clock for targets with asynchronous
|
|
reset methodology. (optional)
|
|
|
|
- vdccx-supply: phandle to the regulator for the vdd supply for
|
|
digital circuit operation.
|
|
- v1p8-supply: phandle to the regulator for the 1.8V supply
|
|
- v3p3-supply: phandle to the regulator for the 3.3V supply
|
|
|
|
- resets: A list of phandle + reset-specifier pairs for the
|
|
resets listed in reset-names
|
|
- reset-names: Should contain the following:
|
|
"phy" USB PHY controller reset
|
|
"link" USB LINK controller reset
|
|
|
|
- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of
|
|
1 - PHY control
|
|
2 - PMIC control
|
|
|
|
Optional properties:
|
|
- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg"
|
|
|
|
- switch-gpio: A phandle + gpio-specifier pair. Some boards are using Dual
|
|
SPDT USB Switch, witch is cotrolled by GPIO to de/multiplex
|
|
D+/D- USB lines between connectors.
|
|
|
|
- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device
|
|
Mode Eye Diagram test. Start address at which these values will be
|
|
written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as
|
|
"do not overwrite default value at this address".
|
|
For example: qcom,phy-init-sequence = < -1 0x63 >;
|
|
Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1.
|
|
|
|
- qcom,phy-num: Select number of pyco-phy to use, can be one of
|
|
0 - PHY one, default
|
|
1 - Second PHY
|
|
Some platforms may have configuration to allow USB
|
|
controller work with any of the two HSPHYs present.
|
|
|
|
- qcom,vdd-levels: This property must be a list of three integer values
|
|
(no, min, max) where each value represents either a voltage
|
|
in microvolts or a value corresponding to voltage corner.
|
|
|
|
- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy
|
|
and controller driver therefore enables pull-up explicitly
|
|
before starting controller using usbcmd run/stop bit.
|
|
|
|
- extcon: phandles to external connector devices. First phandle
|
|
should point to external connector, which provide "USB"
|
|
cable events, the second should point to external connector
|
|
device, which provide "USB-HOST" cable events. If one of
|
|
the external connector devices is not required empty <0>
|
|
phandle should be specified.
|
|
|
|
Example HSUSB OTG controller device node:
|
|
|
|
usb@f9a55000 {
|
|
compatible = "qcom,usb-otg-snps";
|
|
reg = <0xf9a55000 0x400>;
|
|
interrupts = <0 134 0>;
|
|
dr_mode = "peripheral";
|
|
|
|
clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>,
|
|
<&gcc GCC_USB_HS_AHB_CLK>;
|
|
|
|
clock-names = "phy", "core", "iface";
|
|
|
|
vddcx-supply = <&pm8841_s2_corner>;
|
|
v1p8-supply = <&pm8941_l6>;
|
|
v3p3-supply = <&pm8941_l24>;
|
|
|
|
resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>;
|
|
reset-names = "phy", "link";
|
|
|
|
qcom,otg-control = <1>;
|
|
qcom,phy-init-sequence = < -1 0x63 >;
|
|
qcom,vdd-levels = <1 5 7>;
|
|
};
|