mirror of
https://github.com/torvalds/linux.git
synced 2024-12-28 13:51:44 +00:00
0b1a69fd83
Add the devicetree binding for MT8183 SoC Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
71 lines
3.1 KiB
Plaintext
71 lines
3.1 KiB
Plaintext
* MTK MMC controller
|
|
|
|
The MTK MSDC can act as a MMC controller
|
|
to support MMC, SD, and SDIO types of memory cards.
|
|
|
|
This file documents differences between the core properties in mmc.txt
|
|
and the properties used by the msdc driver.
|
|
|
|
Required properties:
|
|
- compatible: value should be either of the following.
|
|
"mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
|
|
"mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
|
|
"mediatek,mt8183-mmc": for mmc host ip compatible with mt8183
|
|
"mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
|
|
"mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
|
|
"mediatek,mt7622-mmc": for MT7622 SoC
|
|
"mediatek,mt7623-mmc", "mediatek,mt2701-mmc": for MT7623 SoC
|
|
|
|
- reg: physical base address of the controller and length
|
|
- interrupts: Should contain MSDC interrupt number
|
|
- clocks: Should contain phandle for the clock feeding the MMC controller
|
|
- clock-names: Should contain the following:
|
|
"source" - source clock (required)
|
|
"hclk" - HCLK which used for host (required)
|
|
"source_cg" - independent source clock gate (required for MT2712)
|
|
"bus_clk" - bus clock used for internal register access (required for MT2712 MSDC0/3)
|
|
- pinctrl-names: should be "default", "state_uhs"
|
|
- pinctrl-0: should contain default/high speed pin ctrl
|
|
- pinctrl-1: should contain uhs mode pin ctrl
|
|
- vmmc-supply: power to the Core
|
|
- vqmmc-supply: power to the IO
|
|
|
|
Optional properties:
|
|
- assigned-clocks: PLL of the source clock
|
|
- assigned-clock-parents: parent of source clock, used for HS400 mode to get 400Mhz source clock
|
|
- hs400-ds-delay: HS400 DS delay setting
|
|
- mediatek,hs200-cmd-int-delay: HS200 command internal delay setting.
|
|
This field has total 32 stages.
|
|
The value is an integer from 0 to 31.
|
|
- mediatek,hs400-cmd-int-delay: HS400 command internal delay setting
|
|
This field has total 32 stages.
|
|
The value is an integer from 0 to 31.
|
|
- mediatek,hs400-cmd-resp-sel-rising: HS400 command response sample selection
|
|
If present,HS400 command responses are sampled on rising edges.
|
|
If not present,HS400 command responses are sampled on falling edges.
|
|
- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc
|
|
error caused by stop clock(fifo full)
|
|
Valid range = [0:0x7]. if not present, default value is 0.
|
|
applied to compatible "mediatek,mt2701-mmc".
|
|
|
|
Examples:
|
|
mmc0: mmc@11230000 {
|
|
compatible = "mediatek,mt8173-mmc", "mediatek,mt8135-mmc";
|
|
reg = <0 0x11230000 0 0x108>;
|
|
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>;
|
|
vmmc-supply = <&mt6397_vemc_3v3_reg>;
|
|
vqmmc-supply = <&mt6397_vio18_reg>;
|
|
clocks = <&pericfg CLK_PERI_MSDC30_0>,
|
|
<&topckgen CLK_TOP_MSDC50_0_H_SEL>;
|
|
clock-names = "source", "hclk";
|
|
pinctrl-names = "default", "state_uhs";
|
|
pinctrl-0 = <&mmc0_pins_default>;
|
|
pinctrl-1 = <&mmc0_pins_uhs>;
|
|
assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
|
|
assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
|
|
hs400-ds-delay = <0x14015>;
|
|
mediatek,hs200-cmd-int-delay = <26>;
|
|
mediatek,hs400-cmd-int-delay = <14>;
|
|
mediatek,hs400-cmd-resp-sel-rising;
|
|
};
|