mirror of
https://github.com/torvalds/linux.git
synced 2024-12-25 12:21:37 +00:00
bc5081617f
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
66 lines
1.6 KiB
Plaintext
66 lines
1.6 KiB
Plaintext
Qualcomm SuperSpeed DWC3 USB SoC controller
|
|
|
|
Required properties:
|
|
- compatible: should contain "qcom,dwc3"
|
|
- clocks: A list of phandle + clock-specifier pairs for the
|
|
clocks listed in clock-names
|
|
- clock-names: Should contain the following:
|
|
"core" Master/Core clock, have to be >= 125 MHz for SS
|
|
operation and >= 60MHz for HS operation
|
|
|
|
Optional clocks:
|
|
"iface" System bus AXI clock. Not present on all platforms
|
|
"sleep" Sleep clock, used when USB3 core goes into low
|
|
power mode (U3).
|
|
|
|
Required child node:
|
|
A child node must exist to represent the core DWC3 IP block. The name of
|
|
the node is not important. The content of the node is defined in dwc3.txt.
|
|
|
|
Phy documentation is provided in the following places:
|
|
Documentation/devicetree/bindings/phy/qcom,dwc3-usb-phy.txt
|
|
|
|
Example device nodes:
|
|
|
|
hs_phy: phy@100f8800 {
|
|
compatible = "qcom,dwc3-hs-usb-phy";
|
|
reg = <0x100f8800 0x30>;
|
|
clocks = <&gcc USB30_0_UTMI_CLK>;
|
|
clock-names = "ref";
|
|
#phy-cells = <0>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
ss_phy: phy@100f8830 {
|
|
compatible = "qcom,dwc3-ss-usb-phy";
|
|
reg = <0x100f8830 0x30>;
|
|
clocks = <&gcc USB30_0_MASTER_CLK>;
|
|
clock-names = "ref";
|
|
#phy-cells = <0>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
usb3_0: usb30@0 {
|
|
compatible = "qcom,dwc3";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
clocks = <&gcc USB30_0_MASTER_CLK>;
|
|
clock-names = "core";
|
|
|
|
ranges;
|
|
|
|
status = "ok";
|
|
|
|
dwc3@10000000 {
|
|
compatible = "snps,dwc3";
|
|
reg = <0x10000000 0xcd00>;
|
|
interrupts = <0 205 0x4>;
|
|
phys = <&hs_phy>, <&ss_phy>;
|
|
phy-names = "usb2-phy", "usb3-phy";
|
|
dr_mode = "host";
|
|
};
|
|
};
|
|
|