mirror of
https://github.com/torvalds/linux.git
synced 2024-11-05 11:32:04 +00:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
85 lines
3.1 KiB
C
85 lines
3.1 KiB
C
/* -*- c-basic-offset: 8 -*- */
|
|
|
|
#ifndef __AMDTP_H
|
|
#define __AMDTP_H
|
|
|
|
#include <asm/types.h>
|
|
#include "ieee1394-ioctl.h"
|
|
|
|
/* The userspace interface for the Audio & Music Data Transmission
|
|
* Protocol driver is really simple. First, open /dev/amdtp, use the
|
|
* ioctl to configure format, rate, dimension and either plug or
|
|
* channel, then start writing samples.
|
|
*
|
|
* The formats supported by the driver are listed below.
|
|
* AMDTP_FORMAT_RAW corresponds to the AM824 raw format, which can
|
|
* carry any number of channels, so use this if you're streaming
|
|
* multichannel audio. The AMDTP_FORMAT_IEC958_PCM corresponds to the
|
|
* AM824 IEC958 encapsulation without the IEC958 data bit set, using
|
|
* AMDTP_FORMAT_IEC958_AC3 will transmit the samples with the data bit
|
|
* set, suitable for transmitting compressed AC-3 audio.
|
|
*
|
|
* The rate field specifies the transmission rate; supported values
|
|
* are 32000, 44100, 48000, 88200, 96000, 176400 and 192000.
|
|
*
|
|
* The dimension field specifies the dimension of the signal, that is,
|
|
* the number of audio channels. Only AMDTP_FORMAT_RAW supports
|
|
* settings greater than 2.
|
|
*
|
|
* The mode field specifies which transmission mode to use. The AMDTP
|
|
* specifies two different transmission modes: blocking and
|
|
* non-blocking. The blocking transmission mode always send a fixed
|
|
* number of samples, typically 8, 16 or 32. To exactly match the
|
|
* transmission rate, the driver alternates between sending empty and
|
|
* non-empty packets. In non-blocking mode, the driver transmits as
|
|
* small packets as possible. For example, for a transmission rate of
|
|
* 44100Hz, the driver should send 5 41/80 samples in every cycle, but
|
|
* this is not possible so instead the driver alternates between
|
|
* sending 5 and 6 samples.
|
|
*
|
|
* The last thing to specify is either the isochronous channel to use
|
|
* or the output plug to connect to. If you know what channel the
|
|
* destination device will listen on, you can specify the channel
|
|
* directly and use the AMDTP_IOC_CHANNEL ioctl. However, if the
|
|
* destination device chooses the channel and uses the IEC61883-1 plug
|
|
* mechanism, you can specify an output plug to connect to. The
|
|
* driver will pick up the channel number from the plug once the
|
|
* destination device locks the output plug control register. In this
|
|
* case set the plug field and use the AMDTP_IOC_PLUG ioctl.
|
|
*
|
|
* Having configured the interface, the driver now accepts writes of
|
|
* regular 16 bit signed little endian samples, with the channels
|
|
* interleaved. For example, 4 channels would look like:
|
|
*
|
|
* | sample 0 | sample 1 ...
|
|
* | ch. 0 | ch. 1 | ch. 2 | ch. 3 | ch. 0 | ...
|
|
* | lsb | msb | lsb | msb | lsb | msb | lsb | msb | lsb | msb | ...
|
|
*
|
|
*/
|
|
|
|
enum {
|
|
AMDTP_FORMAT_RAW,
|
|
AMDTP_FORMAT_IEC958_PCM,
|
|
AMDTP_FORMAT_IEC958_AC3
|
|
};
|
|
|
|
enum {
|
|
AMDTP_MODE_BLOCKING,
|
|
AMDTP_MODE_NON_BLOCKING,
|
|
};
|
|
|
|
enum {
|
|
AMDTP_INPUT_LE16,
|
|
AMDTP_INPUT_BE16,
|
|
};
|
|
|
|
struct amdtp_ioctl {
|
|
__u32 format;
|
|
__u32 rate;
|
|
__u32 dimension;
|
|
__u32 mode;
|
|
union { __u32 channel; __u32 plug; } u;
|
|
};
|
|
|
|
#endif /* __AMDTP_H */
|