Minki/linux
1
0
Fork 1
mirror of https://github.com/torvalds/linux.git synced 2024-12-01 00:21:32 +00:00
Code Issues Packages Projects Releases Wiki Activity
99531e6063
linux/drivers/scsi/ufs/ufshci.h
Subhash Jadavani 57d104c153 ufs: add UFS power management support 
This patch adds support for UFS device and UniPro link power management
during runtime/system PM.

Main idea is to define multiple UFS low power levels based on UFS device
and UFS link power states. This would allow any specific platform or pci
driver to choose the best suited low power level during runtime and
system suspend based on their power goals.

bkops handlig:
To put the UFS device in sleep state when bkops is disabled, first query
the bkops status from the device and enable bkops on device only if
device needs time to perform the bkops.

START_STOP handling:
Before sending START_STOP_UNIT to the device well-known logical unit
(w-lun) to make sure that the device w-lun unit attention condition is
cleared.

Write protection:
UFS device specification allows LUs to be write protected, either
permanently or power on write protected. If any LU is power on write
protected and if the card is power cycled (by powering off VCCQ and/or
VCC rails), LU's write protect status would be lost. So this means those
LUs can be written now. To ensures that UFS device is power cycled only
if the power on protect is not set for any of the LUs, check if power on
write protect is set and if device is in sleep/power-off state & link in
inactive state (Hibern8 or OFF state).
If none of the Logical Units on UFS device is power on write protected
then all UFS device power rails (VCC, VCCQ & VCCQ2) can be turned off if
UFS device is in power-off state and UFS link is in OFF state. But current
implementation would disable all device power rails even if UFS link is
not in OFF state.

Low power mode:
If UFS link is in OFF state then UFS host controller can be power collapsed
to avoid leakage current from it. Note that if UFS host controller is power
collapsed, full UFS reinitialization will be required on resume to
re-establish the link between host and device.

Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-10-01 13:11:23 +02:00

394 lines
12 KiB
C
Raw Blame History

/*
* Universal Flash Storage Host controller driver
*
* This code is based on drivers/scsi/ufs/ufshci.h
* Copyright (C) 2011-2013 Samsung India Software Operations
*
* Authors:
* Santosh Yaraganavi <santosh.sy@samsung.com>
* Vinayak Holikatti <h.vinayak@samsung.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
* See the COPYING file in the top-level directory or visit
* <http://www.gnu.org/licenses/gpl-2.0.html>
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* This program is provided "AS IS" and "WITH ALL FAULTS" and
* without warranty of any kind. You are solely responsible for
* determining the appropriateness of using and distributing
* the program and assume all risks associated with your exercise
* of rights with respect to the program, including but not limited
* to infringement of third party rights, the risks and costs of
* program errors, damage to or loss of data, programs or equipment,
* and unavailability or interruption of operations. Under no
* circumstances will the contributor of this Program be liable for
* any damages of any kind arising from your use or distribution of
* this program.
*/
#ifndef _UFSHCI_H
#define _UFSHCI_H
enum {
TASK_REQ_UPIU_SIZE_DWORDS = 8,
TASK_RSP_UPIU_SIZE_DWORDS = 8,
ALIGNED_UPIU_SIZE = 512,
};
/* UFSHCI Registers */
enum {
REG_CONTROLLER_CAPABILITIES = 0x00,
REG_UFS_VERSION = 0x08,
REG_CONTROLLER_DEV_ID = 0x10,
REG_CONTROLLER_PROD_ID = 0x14,
REG_INTERRUPT_STATUS = 0x20,
REG_INTERRUPT_ENABLE = 0x24,
REG_CONTROLLER_STATUS = 0x30,
REG_CONTROLLER_ENABLE = 0x34,
REG_UIC_ERROR_CODE_PHY_ADAPTER_LAYER = 0x38,
REG_UIC_ERROR_CODE_DATA_LINK_LAYER = 0x3C,
REG_UIC_ERROR_CODE_NETWORK_LAYER = 0x40,
REG_UIC_ERROR_CODE_TRANSPORT_LAYER = 0x44,
REG_UIC_ERROR_CODE_DME = 0x48,
REG_UTP_TRANSFER_REQ_INT_AGG_CONTROL = 0x4C,
REG_UTP_TRANSFER_REQ_LIST_BASE_L = 0x50,
REG_UTP_TRANSFER_REQ_LIST_BASE_H = 0x54,
REG_UTP_TRANSFER_REQ_DOOR_BELL = 0x58,
REG_UTP_TRANSFER_REQ_LIST_CLEAR = 0x5C,
REG_UTP_TRANSFER_REQ_LIST_RUN_STOP = 0x60,
REG_UTP_TASK_REQ_LIST_BASE_L = 0x70,
REG_UTP_TASK_REQ_LIST_BASE_H = 0x74,
REG_UTP_TASK_REQ_DOOR_BELL = 0x78,
REG_UTP_TASK_REQ_LIST_CLEAR = 0x7C,
REG_UTP_TASK_REQ_LIST_RUN_STOP = 0x80,
REG_UIC_COMMAND = 0x90,
REG_UIC_COMMAND_ARG_1 = 0x94,
REG_UIC_COMMAND_ARG_2 = 0x98,
REG_UIC_COMMAND_ARG_3 = 0x9C,
};
/* Controller capability masks */
enum {
MASK_TRANSFER_REQUESTS_SLOTS = 0x0000001F,
MASK_TASK_MANAGEMENT_REQUEST_SLOTS = 0x00070000,
MASK_64_ADDRESSING_SUPPORT = 0x01000000,
MASK_OUT_OF_ORDER_DATA_DELIVERY_SUPPORT = 0x02000000,
MASK_UIC_DME_TEST_MODE_SUPPORT = 0x04000000,
};
/* UFS Version 08h */
#define MINOR_VERSION_NUM_MASK UFS_MASK(0xFFFF, 0)
#define MAJOR_VERSION_NUM_MASK UFS_MASK(0xFFFF, 16)
/* Controller UFSHCI version */
enum {
UFSHCI_VERSION_10 = 0x00010000,
UFSHCI_VERSION_11 = 0x00010100,
};
/*
* HCDDID - Host Controller Identification Descriptor
* - Device ID and Device Class 10h
*/
#define DEVICE_CLASS UFS_MASK(0xFFFF, 0)
#define DEVICE_ID UFS_MASK(0xFF, 24)
/*
* HCPMID - Host Controller Identification Descriptor
* - Product/Manufacturer ID 14h
*/
#define MANUFACTURE_ID_MASK UFS_MASK(0xFFFF, 0)
#define PRODUCT_ID_MASK UFS_MASK(0xFFFF, 16)
#define UFS_BIT(x) (1L << (x))
#define UTP_TRANSFER_REQ_COMPL UFS_BIT(0)
#define UIC_DME_END_PT_RESET UFS_BIT(1)
#define UIC_ERROR UFS_BIT(2)
#define UIC_TEST_MODE UFS_BIT(3)
#define UIC_POWER_MODE UFS_BIT(4)
#define UIC_HIBERNATE_EXIT UFS_BIT(5)
#define UIC_HIBERNATE_ENTER UFS_BIT(6)
#define UIC_LINK_LOST UFS_BIT(7)
#define UIC_LINK_STARTUP UFS_BIT(8)
#define UTP_TASK_REQ_COMPL UFS_BIT(9)
#define UIC_COMMAND_COMPL UFS_BIT(10)
#define DEVICE_FATAL_ERROR UFS_BIT(11)
#define CONTROLLER_FATAL_ERROR UFS_BIT(16)
#define SYSTEM_BUS_FATAL_ERROR UFS_BIT(17)
#define UFSHCD_UIC_PWR_MASK (UIC_HIBERNATE_ENTER |\
UIC_HIBERNATE_EXIT |\
UIC_POWER_MODE)
#define UFSHCD_UIC_MASK (UIC_COMMAND_COMPL | UFSHCD_UIC_PWR_MASK)
#define UFSHCD_ERROR_MASK (UIC_ERROR |\
DEVICE_FATAL_ERROR |\
CONTROLLER_FATAL_ERROR |\
SYSTEM_BUS_FATAL_ERROR)
#define INT_FATAL_ERRORS (DEVICE_FATAL_ERROR |\
CONTROLLER_FATAL_ERROR |\
SYSTEM_BUS_FATAL_ERROR)
/* HCS - Host Controller Status 30h */
#define DEVICE_PRESENT UFS_BIT(0)
#define UTP_TRANSFER_REQ_LIST_READY UFS_BIT(1)
#define UTP_TASK_REQ_LIST_READY UFS_BIT(2)
#define UIC_COMMAND_READY UFS_BIT(3)
#define HOST_ERROR_INDICATOR UFS_BIT(4)
#define DEVICE_ERROR_INDICATOR UFS_BIT(5)
#define UIC_POWER_MODE_CHANGE_REQ_STATUS_MASK UFS_MASK(0x7, 8)
enum {
PWR_OK = 0x0,
PWR_LOCAL = 0x01,
PWR_REMOTE = 0x02,
PWR_BUSY = 0x03,
PWR_ERROR_CAP = 0x04,
PWR_FATAL_ERROR = 0x05,
};
/* HCE - Host Controller Enable 34h */
#define CONTROLLER_ENABLE UFS_BIT(0)
#define CONTROLLER_DISABLE 0x0
/* UECPA - Host UIC Error Code PHY Adapter Layer 38h */
#define UIC_PHY_ADAPTER_LAYER_ERROR UFS_BIT(31)
#define UIC_PHY_ADAPTER_LAYER_ERROR_CODE_MASK 0x1F
/* UECDL - Host UIC Error Code Data Link Layer 3Ch */
#define UIC_DATA_LINK_LAYER_ERROR UFS_BIT(31)
#define UIC_DATA_LINK_LAYER_ERROR_CODE_MASK 0x7FFF
#define UIC_DATA_LINK_LAYER_ERROR_PA_INIT 0x2000
/* UECN - Host UIC Error Code Network Layer 40h */
#define UIC_NETWORK_LAYER_ERROR UFS_BIT(31)
#define UIC_NETWORK_LAYER_ERROR_CODE_MASK 0x7
/* UECT - Host UIC Error Code Transport Layer 44h */
#define UIC_TRANSPORT_LAYER_ERROR UFS_BIT(31)
#define UIC_TRANSPORT_LAYER_ERROR_CODE_MASK 0x7F
/* UECDME - Host UIC Error Code DME 48h */
#define UIC_DME_ERROR UFS_BIT(31)
#define UIC_DME_ERROR_CODE_MASK 0x1
#define INT_AGGR_TIMEOUT_VAL_MASK 0xFF
#define INT_AGGR_COUNTER_THRESHOLD_MASK UFS_MASK(0x1F, 8)
#define INT_AGGR_COUNTER_AND_TIMER_RESET UFS_BIT(16)
#define INT_AGGR_STATUS_BIT UFS_BIT(20)
#define INT_AGGR_PARAM_WRITE UFS_BIT(24)
#define INT_AGGR_ENABLE UFS_BIT(31)
/* UTRLRSR - UTP Transfer Request Run-Stop Register 60h */
#define UTP_TRANSFER_REQ_LIST_RUN_STOP_BIT UFS_BIT(0)
/* UTMRLRSR - UTP Task Management Request Run-Stop Register 80h */
#define UTP_TASK_REQ_LIST_RUN_STOP_BIT UFS_BIT(0)
/* UICCMD - UIC Command */
#define COMMAND_OPCODE_MASK 0xFF
#define GEN_SELECTOR_INDEX_MASK 0xFFFF
#define MIB_ATTRIBUTE_MASK UFS_MASK(0xFFFF, 16)
#define RESET_LEVEL 0xFF
#define ATTR_SET_TYPE_MASK UFS_MASK(0xFF, 16)
#define CONFIG_RESULT_CODE_MASK 0xFF
#define GENERIC_ERROR_CODE_MASK 0xFF
#define UIC_ARG_MIB_SEL(attr, sel) ((((attr) & 0xFFFF) << 16) |\
((sel) & 0xFFFF))
#define UIC_ARG_MIB(attr) UIC_ARG_MIB_SEL(attr, 0)
#define UIC_ARG_ATTR_TYPE(t) (((t) & 0xFF) << 16)
#define UIC_GET_ATTR_ID(v) (((v) >> 16) & 0xFFFF)
/* UIC Commands */
enum uic_cmd_dme {
UIC_CMD_DME_GET = 0x01,
UIC_CMD_DME_SET = 0x02,
UIC_CMD_DME_PEER_GET = 0x03,
UIC_CMD_DME_PEER_SET = 0x04,
UIC_CMD_DME_POWERON = 0x10,
UIC_CMD_DME_POWEROFF = 0x11,
UIC_CMD_DME_ENABLE = 0x12,
UIC_CMD_DME_RESET = 0x14,
UIC_CMD_DME_END_PT_RST = 0x15,
UIC_CMD_DME_LINK_STARTUP = 0x16,
UIC_CMD_DME_HIBER_ENTER = 0x17,
UIC_CMD_DME_HIBER_EXIT = 0x18,
UIC_CMD_DME_TEST_MODE = 0x1A,
};
/* UIC Config result code / Generic error code */
enum {
UIC_CMD_RESULT_SUCCESS = 0x00,
UIC_CMD_RESULT_INVALID_ATTR = 0x01,
UIC_CMD_RESULT_FAILURE = 0x01,
UIC_CMD_RESULT_INVALID_ATTR_VALUE = 0x02,
UIC_CMD_RESULT_READ_ONLY_ATTR = 0x03,
UIC_CMD_RESULT_WRITE_ONLY_ATTR = 0x04,
UIC_CMD_RESULT_BAD_INDEX = 0x05,
UIC_CMD_RESULT_LOCKED_ATTR = 0x06,
UIC_CMD_RESULT_BAD_TEST_FEATURE_INDEX = 0x07,
UIC_CMD_RESULT_PEER_COMM_FAILURE = 0x08,
UIC_CMD_RESULT_BUSY = 0x09,
UIC_CMD_RESULT_DME_FAILURE = 0x0A,
};
#define MASK_UIC_COMMAND_RESULT 0xFF
#define INT_AGGR_COUNTER_THLD_VAL(c) (((c) & 0x1F) << 8)
#define INT_AGGR_TIMEOUT_VAL(t) (((t) & 0xFF) << 0)
/* Interrupt disable masks */
enum {
/* Interrupt disable mask for UFSHCI v1.0 */
INTERRUPT_MASK_ALL_VER_10 = 0x30FFF,
INTERRUPT_MASK_RW_VER_10 = 0x30000,
/* Interrupt disable mask for UFSHCI v1.1 */
INTERRUPT_MASK_ALL_VER_11 = 0x31FFF,
};
/*
* Request Descriptor Definitions
*/
/* Transfer request command type */
enum {
UTP_CMD_TYPE_SCSI = 0x0,
UTP_CMD_TYPE_UFS = 0x1,
UTP_CMD_TYPE_DEV_MANAGE = 0x2,
};
enum {
UTP_SCSI_COMMAND = 0x00000000,
UTP_NATIVE_UFS_COMMAND = 0x10000000,
UTP_DEVICE_MANAGEMENT_FUNCTION = 0x20000000,
UTP_REQ_DESC_INT_CMD = 0x01000000,
};
/* UTP Transfer Request Data Direction (DD) */
enum {
UTP_NO_DATA_TRANSFER = 0x00000000,
UTP_HOST_TO_DEVICE = 0x02000000,
UTP_DEVICE_TO_HOST = 0x04000000,
};
/* Overall command status values */
enum {
OCS_SUCCESS = 0x0,
OCS_INVALID_CMD_TABLE_ATTR = 0x1,
OCS_INVALID_PRDT_ATTR = 0x2,
OCS_MISMATCH_DATA_BUF_SIZE = 0x3,
OCS_MISMATCH_RESP_UPIU_SIZE = 0x4,
OCS_PEER_COMM_FAILURE = 0x5,
OCS_ABORTED = 0x6,
OCS_FATAL_ERROR = 0x7,
OCS_INVALID_COMMAND_STATUS = 0x0F,
MASK_OCS = 0x0F,
};
/* The maximum length of the data byte count field in the PRDT is 256KB */
#define PRDT_DATA_BYTE_COUNT_MAX (256 * 1024)
/* The granularity of the data byte count field in the PRDT is 32-bit */
#define PRDT_DATA_BYTE_COUNT_PAD 4
/**
* struct ufshcd_sg_entry - UFSHCI PRD Entry
* @base_addr: Lower 32bit physical address DW-0
* @upper_addr: Upper 32bit physical address DW-1
* @reserved: Reserved for future use DW-2
* @size: size of physical segment DW-3
*/
struct ufshcd_sg_entry {
__le32 base_addr;
__le32 upper_addr;
__le32 reserved;
__le32 size;
};
/**
* struct utp_transfer_cmd_desc - UFS Command Descriptor structure
* @command_upiu: Command UPIU Frame address
* @response_upiu: Response UPIU Frame address
* @prd_table: Physical Region Descriptor
*/
struct utp_transfer_cmd_desc {
u8 command_upiu[ALIGNED_UPIU_SIZE];
u8 response_upiu[ALIGNED_UPIU_SIZE];
struct ufshcd_sg_entry prd_table[SG_ALL];
};
/**
* struct request_desc_header - Descriptor Header common to both UTRD and UTMRD
* @dword0: Descriptor Header DW0
* @dword1: Descriptor Header DW1
* @dword2: Descriptor Header DW2
* @dword3: Descriptor Header DW3
*/
struct request_desc_header {
__le32 dword_0;
__le32 dword_1;
__le32 dword_2;
__le32 dword_3;
};
/**
* struct utp_transfer_req_desc - UTRD structure
* @header: UTRD header DW-0 to DW-3
* @command_desc_base_addr_lo: UCD base address low DW-4
* @command_desc_base_addr_hi: UCD base address high DW-5
* @response_upiu_length: response UPIU length DW-6
* @response_upiu_offset: response UPIU offset DW-6
* @prd_table_length: Physical region descriptor length DW-7
* @prd_table_offset: Physical region descriptor offset DW-7
*/
struct utp_transfer_req_desc {
/* DW 0-3 */
struct request_desc_header header;
/* DW 4-5*/
__le32 command_desc_base_addr_lo;
__le32 command_desc_base_addr_hi;
/* DW 6 */
__le16 response_upiu_length;
__le16 response_upiu_offset;
/* DW 7 */
__le16 prd_table_length;
__le16 prd_table_offset;
};
/**
* struct utp_task_req_desc - UTMRD structure
* @header: UTMRD header DW-0 to DW-3
* @task_req_upiu: Pointer to task request UPIU DW-4 to DW-11
* @task_rsp_upiu: Pointer to task response UPIU DW12 to DW-19
*/
struct utp_task_req_desc {
/* DW 0-3 */
struct request_desc_header header;
/* DW 4-11 */
__le32 task_req_upiu[TASK_REQ_UPIU_SIZE_DWORDS];
/* DW 12-19 */
__le32 task_rsp_upiu[TASK_RSP_UPIU_SIZE_DWORDS];
};
#endif /* End of Header */
Reference in New Issue View Git Blame Copy Permalink