mirror of
https://github.com/torvalds/linux.git
synced 2024-12-30 06:41:43 +00:00
3f0f4a3f20
Add short documentation for two ALS / proximity chip drivers. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
117 lines
3.5 KiB
Plaintext
117 lines
3.5 KiB
Plaintext
Kernel driver bh1770glc
|
|
=======================
|
|
|
|
Supported chips:
|
|
ROHM BH1770GLC
|
|
OSRAM SFH7770
|
|
|
|
Data sheet:
|
|
Not freely available
|
|
|
|
Author:
|
|
Samu Onkalo <samu.p.onkalo@nokia.com>
|
|
|
|
Description
|
|
-----------
|
|
BH1770GLC and SFH7770 are combined ambient light and proximity sensors.
|
|
ALS and proximity parts operates on their own, but they shares common I2C
|
|
interface and interrupt logic. In principle they can run on their own,
|
|
but ALS side results are used to estimate reliability of the proximity sensor.
|
|
|
|
ALS produces 16 bit lux values. The chip contains interrupt logic to produce
|
|
low and high threshold interrupts.
|
|
|
|
Proximity part contains IR-led driver up to 3 IR leds. The chip measures
|
|
amount of reflected IR light and produces proximity result. Resolution is
|
|
8 bit. Driver supports only one channel. Driver uses ALS results to estimate
|
|
reliability of the proximity results. Thus ALS is always running while
|
|
proximity detection is needed.
|
|
|
|
Driver uses threshold interrupts to avoid need for polling the values.
|
|
Proximity low interrupt doesn't exists in the chip. This is simulated
|
|
by using a delayed work. As long as there is proximity threshold above
|
|
interrupts the delayed work is pushed forward. So, when proximity level goes
|
|
below the threshold value, there is no interrupt and the delayed work will
|
|
finally run. This is handled as no proximity indication.
|
|
|
|
Chip state is controlled via runtime pm framework when enabled in config.
|
|
|
|
Calibscale factor is used to hide differences between the chips. By default
|
|
value set to neutral state meaning factor of 1.00. To get proper values,
|
|
calibrated source of light is needed as a reference. Calibscale factor is set
|
|
so that measurement produces about the expected lux value.
|
|
|
|
SYSFS
|
|
-----
|
|
|
|
chip_id
|
|
RO - shows detected chip type and version
|
|
|
|
power_state
|
|
RW - enable / disable chip. Uses counting logic
|
|
1 enables the chip
|
|
0 disables the chip
|
|
|
|
lux0_input
|
|
RO - measured lux value
|
|
sysfs_notify called when threshold interrupt occurs
|
|
|
|
lux0_sensor_range
|
|
RO - lux0_input max value
|
|
|
|
lux0_rate
|
|
RW - measurement rate in Hz
|
|
|
|
lux0_rate_avail
|
|
RO - supported measurement rates
|
|
|
|
lux0_thresh_above_value
|
|
RW - HI level threshold value. All results above the value
|
|
trigs an interrupt. 65535 (i.e. sensor_range) disables the above
|
|
interrupt.
|
|
|
|
lux0_thresh_below_value
|
|
RW - LO level threshold value. All results below the value
|
|
trigs an interrupt. 0 disables the below interrupt.
|
|
|
|
lux0_calibscale
|
|
RW - calibration value. Set to neutral value by default.
|
|
Output results are multiplied with calibscale / calibscale_default
|
|
value.
|
|
|
|
lux0_calibscale_default
|
|
RO - neutral calibration value
|
|
|
|
prox0_raw
|
|
RO - measured proximity value
|
|
sysfs_notify called when threshold interrupt occurs
|
|
|
|
prox0_sensor_range
|
|
RO - prox0_raw max value
|
|
|
|
prox0_raw_en
|
|
RW - enable / disable proximity - uses counting logic
|
|
1 enables the proximity
|
|
0 disables the proximity
|
|
|
|
prox0_thresh_above_count
|
|
RW - number of proximity interrupts needed before triggering the event
|
|
|
|
prox0_rate_above
|
|
RW - Measurement rate (in Hz) when the level is above threshold
|
|
i.e. when proximity on has been reported.
|
|
|
|
prox0_rate_below
|
|
RW - Measurement rate (in Hz) when the level is below threshold
|
|
i.e. when proximity off has been reported.
|
|
|
|
prox0_rate_avail
|
|
RO - Supported proximity measurement rates in Hz
|
|
|
|
prox0_thresh_above0_value
|
|
RW - threshold level which trigs proximity events.
|
|
Filtered by persistence filter (prox0_thresh_above_count)
|
|
|
|
prox0_thresh_above1_value
|
|
RW - threshold level which trigs event immediately
|