mirror of
https://github.com/torvalds/linux.git
synced 2024-12-28 13:51:44 +00:00
889f4ce60e
The cp110-system-controller0.txt file was renamed to
cp110-system-controller.txt.
Fixes: 4aa5496980 ("dt-bindings: cp110: rename cp110 syscon file")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
94 lines
3.0 KiB
Plaintext
94 lines
3.0 KiB
Plaintext
* Marvell EBU GPIO controller
|
|
|
|
Required properties:
|
|
|
|
- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio",
|
|
"marvell,armadaxp-gpio" or "marvell,armada-8k-gpio".
|
|
|
|
"marvell,orion-gpio" should be used for Orion, Kirkwood, Dove,
|
|
Discovery (except MV78200) and Armada 370. "marvell,mv78200-gpio"
|
|
should be used for the Discovery MV78200.
|
|
|
|
"marvel,armadaxp-gpio" should be used for all Armada XP SoCs
|
|
(MV78230, MV78260, MV78460).
|
|
|
|
"marvell,armada-8k-gpio" should be used for the Armada 7K and 8K
|
|
SoCs (either from AP or CP), see
|
|
Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
|
|
for specific details about the offset property.
|
|
|
|
- reg: Address and length of the register set for the device. Only one
|
|
entry is expected, except for the "marvell,armadaxp-gpio" variant
|
|
for which two entries are expected: one for the general registers,
|
|
one for the per-cpu registers. Not used for marvell,armada-8k-gpio.
|
|
|
|
- interrupts: The list of interrupts that are used for all the pins
|
|
managed by this GPIO bank. There can be more than one interrupt
|
|
(example: 1 interrupt per 8 pins on Armada XP, which means 4
|
|
interrupts per bank of 32 GPIOs).
|
|
|
|
- interrupt-controller: identifies the node as an interrupt controller
|
|
|
|
- #interrupt-cells: specifies the number of cells needed to encode an
|
|
interrupt source. Should be two.
|
|
The first cell is the GPIO number.
|
|
The second cell is used to specify flags:
|
|
bits[3:0] trigger type and level flags:
|
|
1 = low-to-high edge triggered.
|
|
2 = high-to-low edge triggered.
|
|
4 = active high level-sensitive.
|
|
8 = active low level-sensitive.
|
|
|
|
- gpio-controller: marks the device node as a gpio controller
|
|
|
|
- ngpios: number of GPIOs this controller has
|
|
|
|
- #gpio-cells: Should be two. The first cell is the pin number. The
|
|
second cell is reserved for flags, unused at the moment.
|
|
|
|
Optional properties:
|
|
|
|
In order to use the GPIO lines in PWM mode, some additional optional
|
|
properties are required.
|
|
|
|
- compatible: Must contain "marvell,armada-370-gpio"
|
|
|
|
- reg: an additional register set is needed, for the GPIO Blink
|
|
Counter on/off registers.
|
|
|
|
- reg-names: Must contain an entry "pwm" corresponding to the
|
|
additional register range needed for PWM operation.
|
|
|
|
- #pwm-cells: Should be two. The first cell is the GPIO line number. The
|
|
second cell is the period in nanoseconds.
|
|
|
|
- clocks: Must be a phandle to the clock for the GPIO controller.
|
|
|
|
Example:
|
|
|
|
gpio0: gpio@d0018100 {
|
|
compatible = "marvell,armadaxp-gpio";
|
|
reg = <0xd0018100 0x40>,
|
|
<0xd0018800 0x30>;
|
|
ngpios = <32>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <16>, <17>, <18>, <19>;
|
|
};
|
|
|
|
gpio1: gpio@18140 {
|
|
compatible = "marvell,armada-370-gpio";
|
|
reg = <0x18140 0x40>, <0x181c8 0x08>;
|
|
reg-names = "gpio", "pwm";
|
|
ngpios = <17>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
#pwm-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <87>, <88>, <89>;
|
|
clocks = <&coreclk 0>;
|
|
};
|