mirror of
https://github.com/torvalds/linux.git
synced 2024-12-24 11:51:27 +00:00
9b1a6d36c3
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161, we should not be mixing address spaces in the reg property like this driver currently does. This patch updates the driver, dt docs and also the existing dt nodes to pass the sysconfig offset in the syscon dt property. This patch breaks DT compatibility! But this platform is considered WIP, and is only used by a few developers who are upstreaming support for it. This change has been done as a single atomic commit to ensure it is bisectable. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
62 lines
2.1 KiB
Plaintext
62 lines
2.1 KiB
Plaintext
STMicroelectronics SoC DWMAC glue layer controller
|
|
|
|
This file documents differences between the core properties in
|
|
Documentation/devicetree/bindings/net/stmmac.txt
|
|
and what is needed on STi platforms to program the stmmac glue logic.
|
|
|
|
The device node has following properties.
|
|
|
|
Required properties:
|
|
- compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac",
|
|
"st,stih407-dwmac", "st,stid127-dwmac".
|
|
- st,syscon : Should be phandle/offset pair. The phandle to the syscon node which
|
|
encompases the glue register, and the offset of the control register.
|
|
- st,gmac_en: this is to enable the gmac into a dedicated sysctl control
|
|
register available on STiH407 SoC.
|
|
- pinctrl-0: pin-control for all the MII mode supported.
|
|
|
|
Optional properties:
|
|
- resets : phandle pointing to the system reset controller with correct
|
|
reset line index for ethernet reset.
|
|
- st,ext-phyclk: valid only for RMII where PHY can generate 50MHz clock or
|
|
MAC can generate it.
|
|
- st,tx-retime-src: This specifies which clk is wired up to the mac for
|
|
retimeing tx lines. This is totally board dependent and can take one of the
|
|
posssible values from "txclk", "clk_125" or "clkgen".
|
|
If not passed, the internal clock will be used by default.
|
|
- sti-ethclk: this is the phy clock.
|
|
- sti-clkconf: this is an extra sysconfig register, available in new SoCs,
|
|
to program the clk retiming.
|
|
- st,gmac_en: to enable the GMAC, this only is present in some SoCs; e.g.
|
|
STiH407.
|
|
|
|
Example:
|
|
|
|
ethernet0: dwmac@9630000 {
|
|
device_type = "network";
|
|
status = "disabled";
|
|
compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710";
|
|
reg = <0x9630000 0x8000>;
|
|
reg-names = "stmmaceth";
|
|
|
|
st,syscon = <&syscfg_sbc_reg 0x80>;
|
|
st,gmac_en;
|
|
resets = <&softreset STIH407_ETH1_SOFTRESET>;
|
|
reset-names = "stmmaceth";
|
|
|
|
interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>,
|
|
<GIC_SPI 99 IRQ_TYPE_NONE>,
|
|
<GIC_SPI 100 IRQ_TYPE_NONE>;
|
|
interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
|
|
|
|
snps,pbl = <32>;
|
|
snps,mixed-burst;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_rgmii1>;
|
|
|
|
clock-names = "stmmaceth", "sti-ethclk";
|
|
clocks = <&CLK_S_C0_FLEXGEN CLK_EXT2F_A9>,
|
|
<&CLK_S_C0_FLEXGEN CLK_ETH_PHY>;
|
|
};
|