mirror of
https://github.com/torvalds/linux.git
synced 2024-12-26 21:02:19 +00:00
6abe9ea8a5
rs485 allows for robust half-duplex serial communication. It is often implemented by attaching an rs485 transceiver to a UART. The UART's RTS line is wired to the transceiver's Transmit Enable pin and determines whether the transceiver is sending or receiving. Examples for such transceivers are Maxim MAX13451E and TI SN65HVD1781A: https://datasheets.maximintegrated.com/en/ds/MAX13450E-MAX13451E.pdf http://www.ti.com/lit/ds/symlink/sn65hvd1781a-q1.pdf In the devicetree, the transceiver itself is not represented, only the UART is. A few rs485-specific dt-bindings already exist and these go into the UART's device node. This commit adds a binding to set the RTS polarity. Most (if not all) transceivers require the Transmit Enable pin be driven high for sending, but in some cases boards may negate the pin and RTS must then be driven low. Consequently the polarity defaults to active high but can be inverted with the newly added "rs485-rts-active-low" binding. Document this binding in rs485.txt and in the two drivers fsl-imx-uart and fsl-lpuart that are about to be amended with support for it. Curiously, the omap_serial driver defaults to active low and already supports an "rs485-rts-active-high" binding to invert the polarity. This is left unchanged to retain compatibility, but the binding is herewith documented. Cc: Mark Jackson <mpfj@newflow.co.uk> Cc: Michał Oleszczyk <oleszczyk.m@gmail.com> Cc: Rafael Gago Castano <rgc@hms.se> Cc: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
33 lines
884 B
Plaintext
33 lines
884 B
Plaintext
* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART)
|
|
|
|
Required properties:
|
|
- compatible : Should be "fsl,<soc>-uart"
|
|
- reg : Address and length of the register set for the device
|
|
- interrupts : Should contain uart interrupt
|
|
|
|
Optional properties:
|
|
- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
|
|
in DCE mode by default.
|
|
- rs485-rts-delay, rs485-rts-active-low, rs485-rx-during-tx,
|
|
linux,rs485-enabled-at-boot-time: see rs485.txt
|
|
|
|
Please check Documentation/devicetree/bindings/serial/serial.txt
|
|
for the complete list of generic properties.
|
|
|
|
Note: Each uart controller should have an alias correctly numbered
|
|
in "aliases" node.
|
|
|
|
Example:
|
|
|
|
aliases {
|
|
serial0 = &uart1;
|
|
};
|
|
|
|
uart1: serial@73fbc000 {
|
|
compatible = "fsl,imx51-uart", "fsl,imx21-uart";
|
|
reg = <0x73fbc000 0x4000>;
|
|
interrupts = <31>;
|
|
uart-has-rtscts;
|
|
fsl,dte-mode;
|
|
};
|