mirror of
https://github.com/torvalds/linux.git
synced 2024-12-24 11:51:27 +00:00
bbfc6cb720
QCOM USB3.0 core wrapper consist of USB3.0 IP from Synopsys (SNPS) and HS, SS PHY's control and configuration registers. It could operate in device mode (SS, HS, FS) and host mode (SS, HS, FS, LS). Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by: Andy Gross <agross@codeaurora.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
67 lines
1.6 KiB
Plaintext
67 lines
1.6 KiB
Plaintext
Qualcomm SuperSpeed DWC3 USB SoC controller
|
|
|
|
Required properties:
|
|
- compatible: should contain "qcom,dwc3"
|
|
- clocks: A list of phandle + clock-specifier pairs for the
|
|
clocks listed in clock-names
|
|
- clock-names: Should contain the following:
|
|
"core" Master/Core clock, have to be >= 125 MHz for SS
|
|
operation and >= 60MHz for HS operation
|
|
|
|
Optional clocks:
|
|
"iface" System bus AXI clock. Not present on all platforms
|
|
"sleep" Sleep clock, used when USB3 core goes into low
|
|
power mode (U3).
|
|
|
|
Required child node:
|
|
A child node must exist to represent the core DWC3 IP block. The name of
|
|
the node is not important. The content of the node is defined in dwc3.txt.
|
|
|
|
Phy documentation is provided in the following places:
|
|
Documentation/devicetree/bindings/phy/qcom,dwc3-usb-phy.txt
|
|
|
|
Example device nodes:
|
|
|
|
hs_phy: phy@100f8800 {
|
|
compatible = "qcom,dwc3-hs-usb-phy";
|
|
reg = <0x100f8800 0x30>;
|
|
clocks = <&gcc USB30_0_UTMI_CLK>;
|
|
clock-names = "ref";
|
|
#phy-cells = <0>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
ss_phy: phy@100f8830 {
|
|
compatible = "qcom,dwc3-ss-usb-phy";
|
|
reg = <0x100f8830 0x30>;
|
|
clocks = <&gcc USB30_0_MASTER_CLK>;
|
|
clock-names = "ref";
|
|
#phy-cells = <0>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
usb3_0: usb30@0 {
|
|
compatible = "qcom,dwc3";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
clocks = <&gcc USB30_0_MASTER_CLK>;
|
|
clock-names = "core";
|
|
|
|
ranges;
|
|
|
|
status = "ok";
|
|
|
|
dwc3@10000000 {
|
|
compatible = "snps,dwc3";
|
|
reg = <0x10000000 0xcd00>;
|
|
interrupts = <0 205 0x4>;
|
|
phys = <&hs_phy>, <&ss_phy>;
|
|
phy-names = "usb2-phy", "usb3-phy";
|
|
tx-fifo-resize;
|
|
dr_mode = "host";
|
|
};
|
|
};
|
|
|