mirror of
https://github.com/torvalds/linux.git
synced 2024-12-23 11:21:33 +00:00
e68f31f452
This adds support for the Marvell Tauros3 cache controller which is compatible with pl310 cache controller but broadcasts L1 cache operations to L2 cache. While updating the binding documentation, clean up the list of possible compatibles. Also reorder driver compatibles to allow non-ARM derivated to be compatible to ARM cache controller compatibles. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
60 lines
2.5 KiB
Plaintext
60 lines
2.5 KiB
Plaintext
* ARM L2 Cache Controller
|
|
|
|
ARM cores often have a separate level 2 cache controller. There are various
|
|
implementations of the L2 cache controller with compatible programming models.
|
|
The ARM L2 cache representation in the device tree should be done as follows:
|
|
|
|
Required properties:
|
|
|
|
- compatible : should be one of:
|
|
"arm,pl310-cache"
|
|
"arm,l220-cache"
|
|
"arm,l210-cache"
|
|
"bcm,bcm11351-a2-pl310-cache": DEPRECATED by "brcm,bcm11351-a2-pl310-cache"
|
|
"brcm,bcm11351-a2-pl310-cache": For Broadcom bcm11351 chipset where an
|
|
offset needs to be added to the address before passing down to the L2
|
|
cache controller
|
|
"marvell,aurora-system-cache": Marvell Controller designed to be
|
|
compatible with the ARM one, with system cache mode (meaning
|
|
maintenance operations on L1 are broadcasted to the L2 and L2
|
|
performs the same operation).
|
|
"marvell,aurora-outer-cache": Marvell Controller designed to be
|
|
compatible with the ARM one with outer cache mode.
|
|
"marvell,tauros3-cache": Marvell Tauros3 cache controller, compatible
|
|
with arm,pl310-cache controller.
|
|
- cache-unified : Specifies the cache is a unified cache.
|
|
- cache-level : Should be set to 2 for a level 2 cache.
|
|
- reg : Physical base address and size of cache controller's memory mapped
|
|
registers.
|
|
|
|
Optional properties:
|
|
|
|
- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
|
|
read, write and setup latencies. Minimum valid values are 1. Controllers
|
|
without setup latency control should use a value of 0.
|
|
- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
|
|
read, write and setup latencies. Controllers without setup latency control
|
|
should use 0. Controllers without separate read and write Tag RAM latency
|
|
values should only use the first cell.
|
|
- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
|
|
- arm,filter-ranges : <start length> Starting address and length of window to
|
|
filter. Addresses in the filter window are directed to the M1 port. Other
|
|
addresses will go to the M0 port.
|
|
- interrupts : 1 combined interrupt.
|
|
- cache-id-part: cache id part number to be used if it is not present
|
|
on hardware
|
|
- wt-override: If present then L2 is forced to Write through mode
|
|
|
|
Example:
|
|
|
|
L2: cache-controller {
|
|
compatible = "arm,pl310-cache";
|
|
reg = <0xfff12000 0x1000>;
|
|
arm,data-latency = <1 1 1>;
|
|
arm,tag-latency = <2 2 2>;
|
|
arm,filter-ranges = <0x80000000 0x8000000>;
|
|
cache-unified;
|
|
cache-level = <2>;
|
|
interrupts = <45>;
|
|
};
|