mirror of
https://github.com/torvalds/linux.git
synced 2024-12-18 09:02:17 +00:00
b43ab901d6
Sodaville has GPIO controller behind the PCI bus. To my suprissed it is not the same as on PXA. The interrupt & gpio chip can be referenced from the device tree like from any other driver. Unfortunately the driver which uses the gpio interrupt has to use irq_of_parse_and_map() instead of platform_get_irq(). The problem is that the platform device (which is created from the device tree) is most likely created before the interrupt chip is registered and therefore irq_of_parse_and_map() fails. In theory the driver works as module. In reality most of the irq functions are not exported to modules and it is possible that _this_ module is unloaded while the provided irqs are still in use. Signed-off-by: Hans J. Koch <hjk@linutronix.de> [torbenh@linutronix.de: make it work after the irq namespace cleanup, add some device tree entries.] Signed-off-by: Torben Hohn <torbenh@linutronix.de> [bigeasy@linutronix.de: convert to generic irq & gpio chip] Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> [grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage] Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
49 lines
1.5 KiB
Plaintext
49 lines
1.5 KiB
Plaintext
GPIO controller on CE4100 / Sodaville SoCs
|
|
==========================================
|
|
|
|
The bindings for CE4100's GPIO controller match the generic description
|
|
which is covered by the gpio.txt file in this folder.
|
|
|
|
The only additional property is the intel,muxctl property which holds the
|
|
value which is written into the MUXCNTL register.
|
|
|
|
There is no compatible property for now because the driver is probed via
|
|
PCI id (vendor 0x8086 device 0x2e67).
|
|
|
|
The interrupt specifier consists of two cells encoded as follows:
|
|
- <1st cell>: The interrupt-number that identifies the interrupt source.
|
|
- <2nd cell>: The level-sense information, encoded as follows:
|
|
4 - active high level-sensitive
|
|
8 - active low level-sensitive
|
|
|
|
Example of the GPIO device and one user:
|
|
|
|
pcigpio: gpio@b,1 {
|
|
/* two cells for GPIO and interrupt */
|
|
#gpio-cells = <2>;
|
|
#interrupt-cells = <2>;
|
|
compatible = "pci8086,2e67.2",
|
|
"pci8086,2e67",
|
|
"pciclassff0000",
|
|
"pciclassff00";
|
|
|
|
reg = <0x15900 0x0 0x0 0x0 0x0>;
|
|
/* Interrupt line of the gpio device */
|
|
interrupts = <15 1>;
|
|
/* It is an interrupt and GPIO controller itself */
|
|
interrupt-controller;
|
|
gpio-controller;
|
|
intel,muxctl = <0>;
|
|
};
|
|
|
|
testuser@20 {
|
|
compatible = "example,testuser";
|
|
/* User the 11th GPIO line as an active high triggered
|
|
* level interrupt
|
|
*/
|
|
interrupts = <11 8>;
|
|
interrupt-parent = <&pcigpio>;
|
|
/* Use this GPIO also with the gpio functions */
|
|
gpios = <&pcigpio 11 0>;
|
|
};
|