mirror of
https://github.com/torvalds/linux.git
synced 2024-12-18 17:12:55 +00:00
791d3ef2e1
'interrupt-parent' is often documented as part of define bindings, but it is really outside the scope of a device binding. It's never required in a given node as it is often inherited from a parent node. Or it can be implicit if a parent node is an 'interrupt-controller' node. So remove it from all the binding files. Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org>
84 lines
2.6 KiB
Plaintext
84 lines
2.6 KiB
Plaintext
Broadcom STB "UPG GIO" GPIO controller
|
|
|
|
The controller's registers are organized as sets of eight 32-bit
|
|
registers with each set controlling a bank of up to 32 pins. A single
|
|
interrupt is shared for all of the banks handled by the controller.
|
|
|
|
Required properties:
|
|
|
|
- compatible:
|
|
Must be "brcm,brcmstb-gpio"
|
|
|
|
- reg:
|
|
Define the base and range of the I/O address space containing
|
|
the brcmstb GPIO controller registers
|
|
|
|
- #gpio-cells:
|
|
Should be <2>. The first cell is the pin number (within the controller's
|
|
pin space), and the second is used for the following:
|
|
bit[0]: polarity (0 for active-high, 1 for active-low)
|
|
|
|
- gpio-controller:
|
|
Specifies that the node is a GPIO controller.
|
|
|
|
- brcm,gpio-bank-widths:
|
|
Number of GPIO lines for each bank. Number of elements must
|
|
correspond to number of banks suggested by the 'reg' property.
|
|
|
|
Optional properties:
|
|
|
|
- interrupts:
|
|
The interrupt shared by all GPIO lines for this controller.
|
|
|
|
- interrupts-extended:
|
|
Alternate form of specifying interrupts and parents that allows for
|
|
multiple parents. This takes precedence over 'interrupts' and
|
|
'interrupt-parent'. Wakeup-capable GPIO controllers often route their
|
|
wakeup interrupt lines through a different interrupt controller than the
|
|
primary interrupt line, making this property necessary.
|
|
|
|
- #interrupt-cells:
|
|
Should be <2>. The first cell is the GPIO number, the second should specify
|
|
flags. The following subset of flags is supported:
|
|
- bits[3:0] trigger type and level flags
|
|
1 = low-to-high edge triggered
|
|
2 = high-to-low edge triggered
|
|
4 = active high level-sensitive
|
|
8 = active low level-sensitive
|
|
Valid combinations are 1, 2, 3, 4, 8.
|
|
See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
|
|
|
|
- interrupt-controller:
|
|
Marks the device node as an interrupt controller
|
|
|
|
- wakeup-source:
|
|
GPIOs for this controller can be used as a wakeup source
|
|
|
|
Example:
|
|
upg_gio: gpio@f040a700 {
|
|
#gpio-cells = <2>;
|
|
#interrupt-cells = <2>;
|
|
compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
|
|
gpio-controller;
|
|
interrupt-controller;
|
|
reg = <0xf040a700 0x80>;
|
|
interrupt-parent = <&irq0_intc>;
|
|
interrupts = <0x6>;
|
|
brcm,gpio-bank-widths = <32 32 32 24>;
|
|
};
|
|
|
|
upg_gio_aon: gpio@f04172c0 {
|
|
#gpio-cells = <2>;
|
|
#interrupt-cells = <2>;
|
|
compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
|
|
gpio-controller;
|
|
interrupt-controller;
|
|
reg = <0xf04172c0 0x40>;
|
|
interrupt-parent = <&irq0_aon_intc>;
|
|
interrupts = <0x6>;
|
|
interrupts-extended = <&irq0_aon_intc 0x6>,
|
|
<&aon_pm_l2_intc 0x5>;
|
|
wakeup-source;
|
|
brcm,gpio-bank-widths = <18 4>;
|
|
};
|