mirror of
https://github.com/torvalds/linux.git
synced 2024-12-26 12:52:30 +00:00
1888eb75e6
This patch adds syscon based phandle to i2c device nodes of exynos5250 and exynos5420. These phandles will be used to save restore i2c sysreg configuration register during s2r from i2c driver. CC: Rob Herring <robh+dt@kernel.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Russell King <linux@arm.linux.org.uk> CC: devicetree@vger.kernel.org CC: linux-doc@vger.kernel.org Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
61 lines
2.3 KiB
Plaintext
61 lines
2.3 KiB
Plaintext
* Samsung's I2C controller
|
|
|
|
The Samsung's I2C controller is used to interface with I2C devices.
|
|
|
|
Required properties:
|
|
- compatible: value should be either of the following.
|
|
(a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
|
|
(b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
|
|
(c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
|
|
inside HDMIPHY block found on several samsung SoCs
|
|
(d) "samsung, exynos5440-i2c", for s3c2440-like i2c used
|
|
on EXYNOS5440 which does not need GPIO configuration.
|
|
(e) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as
|
|
a host to SATA PHY controller on an internal bus.
|
|
- reg: physical base address of the controller and length of memory mapped
|
|
region.
|
|
- interrupts: interrupt number to the cpu.
|
|
- samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
|
|
|
|
Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
|
|
- Samsung GPIO variant (deprecated):
|
|
- gpios: The order of the gpios should be the following: <SDA, SCL>.
|
|
The gpio specifier depends on the gpio controller. Required in all
|
|
cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
|
|
lines are permanently wired to the respective clienta
|
|
- Pinctrl variant (preferred, if available):
|
|
- pinctrl-0: Pin control group to be used for this controller.
|
|
- pinctrl-names: Should contain only one value - "default".
|
|
|
|
Optional properties:
|
|
- samsung,i2c-slave-addr: Slave address in multi-master environment. If not
|
|
specified, default value is 0.
|
|
- samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
|
|
specified, the default value in Hz is 100000.
|
|
- samsung,sysreg-phandle - handle to syscon used to control the system registers
|
|
|
|
Example:
|
|
|
|
i2c@13870000 {
|
|
compatible = "samsung,s3c2440-i2c";
|
|
reg = <0x13870000 0x100>;
|
|
interrupts = <345>;
|
|
samsung,i2c-sda-delay = <100>;
|
|
samsung,i2c-max-bus-freq = <100000>;
|
|
/* Samsung GPIO variant begins here */
|
|
gpios = <&gpd1 2 0 /* SDA */
|
|
&gpd1 3 0 /* SCL */>;
|
|
/* Samsung GPIO variant ends here */
|
|
/* Pinctrl variant begins here */
|
|
pinctrl-0 = <&i2c3_bus>;
|
|
pinctrl-names = "default";
|
|
/* Pinctrl variant ends here */
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
wm8994@1a {
|
|
compatible = "wlf,wm8994";
|
|
reg = <0x1a>;
|
|
};
|
|
};
|