mirror of
https://github.com/torvalds/linux.git
synced 2024-12-28 05:41:55 +00:00
73c90d943e
Add the reg-io-width property to describe the width of the memory accesses. Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: devicetree@vger.kernel.org Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Tested-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
58 lines
1.7 KiB
Plaintext
58 lines
1.7 KiB
Plaintext
Memory mapped SJA1000 CAN controller from NXP (formerly Philips)
|
|
|
|
Required properties:
|
|
|
|
- compatible : should be "nxp,sja1000".
|
|
|
|
- reg : should specify the chip select, address offset and size required
|
|
to map the registers of the SJA1000. The size is usually 0x80.
|
|
|
|
- interrupts: property with a value describing the interrupt source
|
|
(number and sensitivity) required for the SJA1000.
|
|
|
|
Optional properties:
|
|
|
|
- reg-io-width : Specify the size (in bytes) of the IO accesses that
|
|
should be performed on the device. Valid value is 1, 2 or 4.
|
|
Default to 1 (8 bits).
|
|
|
|
- nxp,external-clock-frequency : Frequency of the external oscillator
|
|
clock in Hz. Note that the internal clock frequency used by the
|
|
SJA1000 is half of that value. If not specified, a default value
|
|
of 16000000 (16 MHz) is used.
|
|
|
|
- nxp,tx-output-mode : operation mode of the TX output control logic:
|
|
<0x0> : bi-phase output mode
|
|
<0x1> : normal output mode (default)
|
|
<0x2> : test output mode
|
|
<0x3> : clock output mode
|
|
|
|
- nxp,tx-output-config : TX output pin configuration:
|
|
<0x01> : TX0 invert
|
|
<0x02> : TX0 pull-down (default)
|
|
<0x04> : TX0 pull-up
|
|
<0x06> : TX0 push-pull
|
|
<0x08> : TX1 invert
|
|
<0x10> : TX1 pull-down
|
|
<0x20> : TX1 pull-up
|
|
<0x30> : TX1 push-pull
|
|
|
|
- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin.
|
|
If not specified or if the specified value is 0, the CLKOUT pin
|
|
will be disabled.
|
|
|
|
- nxp,no-comparator-bypass : Allows to disable the CAN input comparator.
|
|
|
|
For further information, please have a look to the SJA1000 data sheet.
|
|
|
|
Examples:
|
|
|
|
can@3,100 {
|
|
compatible = "nxp,sja1000";
|
|
reg = <3 0x100 0x80>;
|
|
interrupts = <2 0>;
|
|
interrupt-parent = <&mpic>;
|
|
nxp,external-clock-frequency = <16000000>;
|
|
};
|
|
|