mirror of
https://github.com/torvalds/linux.git
synced 2024-12-25 12:21:37 +00:00
6edc794a5f
This patch extends the driver with any necessary SoC-specific definitions to support EXYNOS4X12 SoCs. Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
266 lines
9.6 KiB
Plaintext
266 lines
9.6 KiB
Plaintext
Samsung GPIO and Pin Mux/Config controller
|
|
|
|
Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
|
|
controller. It controls the input/output settings on the available pads/pins
|
|
and also provides ability to multiplex and configure the output of various
|
|
on-chip controllers onto these pads.
|
|
|
|
Required Properties:
|
|
- compatible: should be one of the following.
|
|
- "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
|
|
- "samsung,pinctrl-exynos4x12": for Exynos4x12 compatible pin-controller.
|
|
- "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
|
|
|
|
- reg: Base address of the pin controller hardware module and length of
|
|
the address space it occupies.
|
|
|
|
- Pin banks as child nodes: Pin banks of the controller are represented by child
|
|
nodes of the controller node. Bank name is taken from name of the node. Each
|
|
bank node must contain following properties:
|
|
|
|
- gpio-controller: identifies the node as a gpio controller and pin bank.
|
|
- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
|
|
binding is used, the amount of cells must be specified as 2. See generic
|
|
GPIO binding documentation for description of particular cells.
|
|
|
|
- Pin mux/config groups as child nodes: The pin mux (selecting pin function
|
|
mode) and pin config (pull up/down, driver strength) settings are represented
|
|
as child nodes of the pin-controller node. There should be atleast one
|
|
child node and there is no limit on the count of these child nodes.
|
|
|
|
The child node should contain a list of pin(s) on which a particular pin
|
|
function selection or pin configuration (or both) have to applied. This
|
|
list of pins is specified using the property name "samsung,pins". There
|
|
should be atleast one pin specfied for this property and there is no upper
|
|
limit on the count of pins that can be specified. The pins are specified
|
|
using pin names which are derived from the hardware manual of the SoC. As
|
|
an example, the pins in GPA0 bank of the pin controller can be represented
|
|
as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
|
|
The format of the pin names should be (as per the hardware manual)
|
|
"[pin bank name]-[pin number within the bank]".
|
|
|
|
The pin function selection that should be applied on the pins listed in the
|
|
child node is specified using the "samsung,pin-function" property. The value
|
|
of this property that should be applied to each of the pins listed in the
|
|
"samsung,pins" property should be picked from the hardware manual of the SoC
|
|
for the specified pin group. This property is optional in the child node if
|
|
no specific function selection is desired for the pins listed in the child
|
|
node. The value of this property is used as-is to program the pin-controller
|
|
function selector register of the pin-bank.
|
|
|
|
The child node can also optionally specify one or more of the pin
|
|
configuration that should be applied on all the pins listed in the
|
|
"samsung,pins" property of the child node. The following pin configuration
|
|
properties are supported.
|
|
|
|
- samsung,pin-pud: Pull up/down configuration.
|
|
- samsung,pin-drv: Drive strength configuration.
|
|
- samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
|
|
- samsung,pin-drv-pdn: Drive strength configuration in power down mode.
|
|
|
|
The values specified by these config properties should be derived from the
|
|
hardware manual and these values are programmed as-is into the pin
|
|
pull up/down and driver strength register of the pin-controller.
|
|
|
|
Note: A child should include atleast a pin function selection property or
|
|
pin configuration property (one or more) or both.
|
|
|
|
The client nodes that require a particular pin function selection and/or
|
|
pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
|
|
file.
|
|
|
|
External GPIO and Wakeup Interrupts:
|
|
|
|
The controller supports two types of external interrupts over gpio. The first
|
|
is the external gpio interrupt and second is the external wakeup interrupts.
|
|
The difference between the two is that the external wakeup interrupts can be
|
|
used as system wakeup events.
|
|
|
|
A. External GPIO Interrupts: For supporting external gpio interrupts, the
|
|
following properties should be specified in the pin-controller device node.
|
|
|
|
- interrupt-parent: phandle of the interrupt parent to which the external
|
|
GPIO interrupts are forwarded to.
|
|
- interrupts: interrupt specifier for the controller. The format and value of
|
|
the interrupt specifier depends on the interrupt parent for the controller.
|
|
|
|
In addition, following properties must be present in node of every bank
|
|
of pins supporting GPIO interrupts:
|
|
|
|
- interrupt-controller: identifies the controller node as interrupt-parent.
|
|
- #interrupt-cells: the value of this property should be 2.
|
|
- First Cell: represents the external gpio interrupt number local to the
|
|
external gpio interrupt space of the controller.
|
|
- Second Cell: flags to identify the type of the interrupt
|
|
- 1 = rising edge triggered
|
|
- 2 = falling edge triggered
|
|
- 3 = rising and falling edge triggered
|
|
- 4 = high level triggered
|
|
- 8 = low level triggered
|
|
|
|
B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
|
|
child node representing the external wakeup interrupt controller should be
|
|
included in the pin-controller device node. This child node should include
|
|
the following properties.
|
|
|
|
- compatible: identifies the type of the external wakeup interrupt controller
|
|
The possible values are:
|
|
- samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
|
|
found on Samsung Exynos4210 SoC.
|
|
- interrupt-parent: phandle of the interrupt parent to which the external
|
|
wakeup interrupts are forwarded to.
|
|
- interrupts: interrupt used by multiplexed wakeup interrupts.
|
|
|
|
In addition, following properties must be present in node of every bank
|
|
of pins supporting wake-up interrupts:
|
|
|
|
- interrupt-controller: identifies the node as interrupt-parent.
|
|
- #interrupt-cells: the value of this property should be 2
|
|
- First Cell: represents the external wakeup interrupt number local to
|
|
the external wakeup interrupt space of the controller.
|
|
- Second Cell: flags to identify the type of the interrupt
|
|
- 1 = rising edge triggered
|
|
- 2 = falling edge triggered
|
|
- 3 = rising and falling edge triggered
|
|
- 4 = high level triggered
|
|
- 8 = low level triggered
|
|
|
|
Node of every bank of pins supporting direct wake-up interrupts (without
|
|
multiplexing) must contain following properties:
|
|
|
|
- interrupt-parent: phandle of the interrupt parent to which the external
|
|
wakeup interrupts are forwarded to.
|
|
- interrupts: interrupts of the interrupt parent which are used for external
|
|
wakeup interrupts from pins of the bank, must contain interrupts for all
|
|
pins of the bank.
|
|
|
|
Aliases:
|
|
|
|
All the pin controller nodes should be represented in the aliases node using
|
|
the following format 'pinctrl{n}' where n is a unique number for the alias.
|
|
|
|
Example: A pin-controller node with pin banks:
|
|
|
|
pinctrl_0: pinctrl@11400000 {
|
|
compatible = "samsung,pinctrl-exynos4210";
|
|
reg = <0x11400000 0x1000>;
|
|
interrupts = <0 47 0>;
|
|
|
|
/* ... */
|
|
|
|
/* Pin bank without external interrupts */
|
|
gpy0: gpy0 {
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
};
|
|
|
|
/* ... */
|
|
|
|
/* Pin bank with external GPIO or muxed wake-up interrupts */
|
|
gpj0: gpj0 {
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
/* ... */
|
|
|
|
/* Pin bank with external direct wake-up interrupts */
|
|
gpx0: gpx0 {
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
interrupt-controller;
|
|
interrupt-parent = <&gic>;
|
|
interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
|
|
<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
/* ... */
|
|
};
|
|
|
|
Example 1: A pin-controller node with pin groups.
|
|
|
|
pinctrl_0: pinctrl@11400000 {
|
|
compatible = "samsung,pinctrl-exynos4210";
|
|
reg = <0x11400000 0x1000>;
|
|
interrupts = <0 47 0>;
|
|
|
|
/* ... */
|
|
|
|
uart0_data: uart0-data {
|
|
samsung,pins = "gpa0-0", "gpa0-1";
|
|
samsung,pin-function = <2>;
|
|
samsung,pin-pud = <0>;
|
|
samsung,pin-drv = <0>;
|
|
};
|
|
|
|
uart0_fctl: uart0-fctl {
|
|
samsung,pins = "gpa0-2", "gpa0-3";
|
|
samsung,pin-function = <2>;
|
|
samsung,pin-pud = <0>;
|
|
samsung,pin-drv = <0>;
|
|
};
|
|
|
|
uart1_data: uart1-data {
|
|
samsung,pins = "gpa0-4", "gpa0-5";
|
|
samsung,pin-function = <2>;
|
|
samsung,pin-pud = <0>;
|
|
samsung,pin-drv = <0>;
|
|
};
|
|
|
|
uart1_fctl: uart1-fctl {
|
|
samsung,pins = "gpa0-6", "gpa0-7";
|
|
samsung,pin-function = <2>;
|
|
samsung,pin-pud = <0>;
|
|
samsung,pin-drv = <0>;
|
|
};
|
|
|
|
i2c2_bus: i2c2-bus {
|
|
samsung,pins = "gpa0-6", "gpa0-7";
|
|
samsung,pin-function = <3>;
|
|
samsung,pin-pud = <3>;
|
|
samsung,pin-drv = <0>;
|
|
};
|
|
};
|
|
|
|
Example 2: A pin-controller node with external wakeup interrupt controller node.
|
|
|
|
pinctrl_1: pinctrl@11000000 {
|
|
compatible = "samsung,pinctrl-exynos4210";
|
|
reg = <0x11000000 0x1000>;
|
|
interrupts = <0 46 0>
|
|
|
|
/* ... */
|
|
|
|
wakeup-interrupt-controller {
|
|
compatible = "samsung,exynos4210-wakeup-eint";
|
|
interrupt-parent = <&gic>;
|
|
interrupts = <0 32 0>;
|
|
};
|
|
};
|
|
|
|
Example 3: A uart client node that supports 'default' and 'flow-control' states.
|
|
|
|
uart@13800000 {
|
|
compatible = "samsung,exynos4210-uart";
|
|
reg = <0x13800000 0x100>;
|
|
interrupts = <0 52 0>;
|
|
pinctrl-names = "default", "flow-control;
|
|
pinctrl-0 = <&uart0_data>;
|
|
pinctrl-1 = <&uart0_data &uart0_fctl>;
|
|
};
|
|
|
|
Example 4: Set up the default pin state for uart controller.
|
|
|
|
static int s3c24xx_serial_probe(struct platform_device *pdev) {
|
|
struct pinctrl *pinctrl;
|
|
|
|
/* ... */
|
|
|
|
pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
|
|
}
|