mirror of
https://github.com/torvalds/linux.git
synced 2024-12-30 14:52:05 +00:00
270d5aad53
Add DT bindings for PHY interface built into USB3 controller implemented in UniPhier SoCs. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
58 lines
1.8 KiB
Plaintext
58 lines
1.8 KiB
Plaintext
Socionext UniPhier USB3 Super-Speed (SS) PHY
|
|
|
|
This describes the devicetree bindings for PHY interfaces built into
|
|
USB3 controller implemented on Socionext UniPhier SoCs.
|
|
Although the controller includes High-Speed PHY and Super-Speed PHY,
|
|
this describes about Super-Speed PHY.
|
|
|
|
Required properties:
|
|
- compatible: Should contain one of the following:
|
|
"socionext,uniphier-pro4-usb3-ssphy" - for Pro4 SoC
|
|
"socionext,uniphier-pxs2-usb3-ssphy" - for PXs2 SoC
|
|
"socionext,uniphier-ld20-usb3-ssphy" - for LD20 SoC
|
|
"socionext,uniphier-pxs3-usb3-ssphy" - for PXs3 SoC
|
|
- reg: Specifies offset and length of the register set for the device.
|
|
- #phy-cells: Should be 0.
|
|
- clocks: A list of phandles to the clock gate for USB3 glue layer.
|
|
According to the clock-names, appropriate clocks are required.
|
|
- clock-names:
|
|
"gio", "link" - for Pro4 SoC
|
|
"phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
|
|
"phy", "link" - for others
|
|
- resets: A list of phandles to the reset control for USB3 glue layer.
|
|
According to the reset-names, appropriate resets are required.
|
|
- reset-names:
|
|
"gio", "link" - for Pro4 SoC
|
|
"phy", "link" - for others
|
|
|
|
Optional properties:
|
|
- vbus-supply: A phandle to the regulator for USB VBUS.
|
|
|
|
Refer to phy/phy-bindings.txt for the generic PHY binding properties.
|
|
|
|
Example:
|
|
|
|
usb-glue@65b00000 {
|
|
compatible = "socionext,uniphier-ld20-dwc3-glue",
|
|
"simple-mfd";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges = <0 0x65b00000 0x400>;
|
|
|
|
usb_vbus0: regulator {
|
|
...
|
|
};
|
|
|
|
usb_ssphy0: ss-phy@300 {
|
|
compatible = "socionext,uniphier-ld20-usb3-ssphy";
|
|
reg = <0x300 0x10>;
|
|
#phy-cells = <0>;
|
|
clock-names = "link", "phy";
|
|
clocks = <&sys_clk 14>, <&sys_clk 16>;
|
|
reset-names = "link", "phy";
|
|
resets = <&sys_rst 14>, <&sys_rst 16>;
|
|
vbus-supply = <&usb_vbus0>;
|
|
};
|
|
...
|
|
};
|