mirror of
https://github.com/torvalds/linux.git
synced 2024-11-01 09:41:44 +00:00
180cb7d6ab
The old cpufreq driver is not necessary anymore with DT and cpufreq-cpu0. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
365 lines
9.8 KiB
C
365 lines
9.8 KiB
C
/*
|
|
*
|
|
* Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
|
|
*
|
|
* based on board-mx51_babbage.c which is
|
|
* Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
|
|
* Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
|
|
*
|
|
* The code contained herein is licensed under the GNU General Public
|
|
* License. You may obtain a copy of the GNU General Public License
|
|
* Version 2 or later at the following locations:
|
|
*
|
|
* http://www.opensource.org/licenses/gpl-license.html
|
|
* http://www.gnu.org/copyleft/gpl.html
|
|
*/
|
|
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/i2c/tsc2007.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/io.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/i2c-gpio.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/can/platform/mcp251x.h>
|
|
|
|
#include <asm/setup.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/time.h>
|
|
|
|
#include "common.h"
|
|
#include "devices-imx51.h"
|
|
#include "eukrea-baseboards.h"
|
|
#include "hardware.h"
|
|
#include "iomux-mx51.h"
|
|
|
|
#define USBH1_RST IMX_GPIO_NR(2, 28)
|
|
#define ETH_RST IMX_GPIO_NR(2, 31)
|
|
#define TSC2007_IRQGPIO_REV2 IMX_GPIO_NR(3, 12)
|
|
#define TSC2007_IRQGPIO_REV3 IMX_GPIO_NR(4, 0)
|
|
#define CAN_IRQGPIO IMX_GPIO_NR(1, 1)
|
|
#define CAN_RST IMX_GPIO_NR(4, 15)
|
|
#define CAN_NCS IMX_GPIO_NR(4, 24)
|
|
#define CAN_RXOBF_REV2 IMX_GPIO_NR(1, 4)
|
|
#define CAN_RXOBF_REV3 IMX_GPIO_NR(3, 12)
|
|
#define CAN_RX1BF IMX_GPIO_NR(1, 6)
|
|
#define CAN_TXORTS IMX_GPIO_NR(1, 7)
|
|
#define CAN_TX1RTS IMX_GPIO_NR(1, 8)
|
|
#define CAN_TX2RTS IMX_GPIO_NR(1, 9)
|
|
#define I2C_SCL IMX_GPIO_NR(4, 16)
|
|
#define I2C_SDA IMX_GPIO_NR(4, 17)
|
|
|
|
/* USB_CTRL_1 */
|
|
#define MX51_USB_CTRL_1_OFFSET 0x10
|
|
#define MX51_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
|
|
|
|
#define MX51_USB_PLLDIV_12_MHZ 0x00
|
|
#define MX51_USB_PLL_DIV_19_2_MHZ 0x01
|
|
#define MX51_USB_PLL_DIV_24_MHZ 0x02
|
|
|
|
static iomux_v3_cfg_t eukrea_cpuimx51sd_pads[] = {
|
|
/* UART1 */
|
|
MX51_PAD_UART1_RXD__UART1_RXD,
|
|
MX51_PAD_UART1_TXD__UART1_TXD,
|
|
MX51_PAD_UART1_RTS__UART1_RTS,
|
|
MX51_PAD_UART1_CTS__UART1_CTS,
|
|
|
|
/* USB HOST1 */
|
|
MX51_PAD_USBH1_CLK__USBH1_CLK,
|
|
MX51_PAD_USBH1_DIR__USBH1_DIR,
|
|
MX51_PAD_USBH1_NXT__USBH1_NXT,
|
|
MX51_PAD_USBH1_DATA0__USBH1_DATA0,
|
|
MX51_PAD_USBH1_DATA1__USBH1_DATA1,
|
|
MX51_PAD_USBH1_DATA2__USBH1_DATA2,
|
|
MX51_PAD_USBH1_DATA3__USBH1_DATA3,
|
|
MX51_PAD_USBH1_DATA4__USBH1_DATA4,
|
|
MX51_PAD_USBH1_DATA5__USBH1_DATA5,
|
|
MX51_PAD_USBH1_DATA6__USBH1_DATA6,
|
|
MX51_PAD_USBH1_DATA7__USBH1_DATA7,
|
|
MX51_PAD_USBH1_STP__USBH1_STP,
|
|
MX51_PAD_EIM_CS3__GPIO2_28, /* PHY nRESET */
|
|
|
|
/* FEC */
|
|
MX51_PAD_EIM_DTACK__GPIO2_31, /* PHY nRESET */
|
|
|
|
/* HSI2C */
|
|
MX51_PAD_I2C1_CLK__GPIO4_16,
|
|
MX51_PAD_I2C1_DAT__GPIO4_17,
|
|
|
|
/* I2C1 */
|
|
MX51_PAD_SD2_CMD__I2C1_SCL,
|
|
MX51_PAD_SD2_CLK__I2C1_SDA,
|
|
|
|
/* CAN */
|
|
MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
|
|
MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
|
|
MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
|
|
MX51_PAD_CSPI1_SS0__GPIO4_24, /* nCS */
|
|
MX51_PAD_CSI2_PIXCLK__GPIO4_15, /* nReset */
|
|
MX51_PAD_GPIO1_1__GPIO1_1, /* IRQ */
|
|
MX51_PAD_GPIO1_4__GPIO1_4, /* Control signals */
|
|
MX51_PAD_GPIO1_6__GPIO1_6,
|
|
MX51_PAD_GPIO1_7__GPIO1_7,
|
|
MX51_PAD_GPIO1_8__GPIO1_8,
|
|
MX51_PAD_GPIO1_9__GPIO1_9,
|
|
|
|
/* Touchscreen */
|
|
/* IRQ */
|
|
NEW_PAD_CTRL(MX51_PAD_GPIO_NAND__GPIO_NAND, PAD_CTL_PUS_22K_UP |
|
|
PAD_CTL_PKE | PAD_CTL_SRE_FAST |
|
|
PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
|
|
NEW_PAD_CTRL(MX51_PAD_NANDF_D8__GPIO4_0, PAD_CTL_PUS_22K_UP |
|
|
PAD_CTL_PKE | PAD_CTL_SRE_FAST |
|
|
PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
|
|
};
|
|
|
|
static const struct imxuart_platform_data uart_pdata __initconst = {
|
|
.flags = IMXUART_HAVE_RTSCTS,
|
|
};
|
|
|
|
static int tsc2007_get_pendown_state(void)
|
|
{
|
|
if (mx51_revision() < IMX_CHIP_REVISION_3_0)
|
|
return !gpio_get_value(TSC2007_IRQGPIO_REV2);
|
|
else
|
|
return !gpio_get_value(TSC2007_IRQGPIO_REV3);
|
|
}
|
|
|
|
static struct tsc2007_platform_data tsc2007_info = {
|
|
.model = 2007,
|
|
.x_plate_ohms = 180,
|
|
.get_pendown_state = tsc2007_get_pendown_state,
|
|
};
|
|
|
|
static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
|
|
{
|
|
I2C_BOARD_INFO("pcf8563", 0x51),
|
|
}, {
|
|
I2C_BOARD_INFO("tsc2007", 0x49),
|
|
.platform_data = &tsc2007_info,
|
|
},
|
|
};
|
|
|
|
static const struct mxc_nand_platform_data
|
|
eukrea_cpuimx51sd_nand_board_info __initconst = {
|
|
.width = 1,
|
|
.hw_ecc = 1,
|
|
.flash_bbt = 1,
|
|
};
|
|
|
|
/* This function is board specific as the bit mask for the plldiv will also
|
|
be different for other Freescale SoCs, thus a common bitmask is not
|
|
possible and cannot get place in /plat-mxc/ehci.c.*/
|
|
static int initialize_otg_port(struct platform_device *pdev)
|
|
{
|
|
u32 v;
|
|
void __iomem *usb_base;
|
|
void __iomem *usbother_base;
|
|
|
|
usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
|
|
if (!usb_base)
|
|
return -ENOMEM;
|
|
usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
|
|
|
|
/* Set the PHY clock to 19.2MHz */
|
|
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
|
|
v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
|
|
v |= MX51_USB_PLL_DIV_19_2_MHZ;
|
|
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
|
|
iounmap(usb_base);
|
|
|
|
mdelay(10);
|
|
|
|
return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
|
|
}
|
|
|
|
static int initialize_usbh1_port(struct platform_device *pdev)
|
|
{
|
|
u32 v;
|
|
void __iomem *usb_base;
|
|
void __iomem *usbother_base;
|
|
|
|
usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
|
|
if (!usb_base)
|
|
return -ENOMEM;
|
|
usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
|
|
|
|
/* The clock for the USBH1 ULPI port will come from the PHY. */
|
|
v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
|
|
__raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN,
|
|
usbother_base + MX51_USB_CTRL_1_OFFSET);
|
|
iounmap(usb_base);
|
|
|
|
mdelay(10);
|
|
|
|
return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED |
|
|
MXC_EHCI_ITC_NO_THRESHOLD);
|
|
}
|
|
|
|
static const struct mxc_usbh_platform_data dr_utmi_config __initconst = {
|
|
.init = initialize_otg_port,
|
|
.portsc = MXC_EHCI_UTMI_16BIT,
|
|
};
|
|
|
|
static const struct fsl_usb2_platform_data usb_pdata __initconst = {
|
|
.operating_mode = FSL_USB2_DR_DEVICE,
|
|
.phy_mode = FSL_USB2_PHY_UTMI_WIDE,
|
|
};
|
|
|
|
static const struct mxc_usbh_platform_data usbh1_config __initconst = {
|
|
.init = initialize_usbh1_port,
|
|
.portsc = MXC_EHCI_MODE_ULPI,
|
|
};
|
|
|
|
static bool otg_mode_host __initdata;
|
|
|
|
static int __init eukrea_cpuimx51sd_otg_mode(char *options)
|
|
{
|
|
if (!strcmp(options, "host"))
|
|
otg_mode_host = true;
|
|
else if (!strcmp(options, "device"))
|
|
otg_mode_host = false;
|
|
else
|
|
pr_info("otg_mode neither \"host\" nor \"device\". "
|
|
"Defaulting to device\n");
|
|
return 1;
|
|
}
|
|
__setup("otg_mode=", eukrea_cpuimx51sd_otg_mode);
|
|
|
|
static struct i2c_gpio_platform_data pdata = {
|
|
.sda_pin = I2C_SDA,
|
|
.sda_is_open_drain = 0,
|
|
.scl_pin = I2C_SCL,
|
|
.scl_is_open_drain = 0,
|
|
.udelay = 2,
|
|
};
|
|
|
|
static struct platform_device hsi2c_gpio_device = {
|
|
.name = "i2c-gpio",
|
|
.id = 0,
|
|
.dev.platform_data = &pdata,
|
|
};
|
|
|
|
static struct mcp251x_platform_data mcp251x_info = {
|
|
.oscillator_frequency = 24E6,
|
|
};
|
|
|
|
static struct spi_board_info cpuimx51sd_spi_device[] = {
|
|
{
|
|
.modalias = "mcp2515",
|
|
.max_speed_hz = 10000000,
|
|
.bus_num = 0,
|
|
.mode = SPI_MODE_0,
|
|
.chip_select = 0,
|
|
.platform_data = &mcp251x_info,
|
|
/* irq number is run-time assigned */
|
|
},
|
|
};
|
|
|
|
static int cpuimx51sd_spi1_cs[] = {
|
|
CAN_NCS,
|
|
};
|
|
|
|
static const struct spi_imx_master cpuimx51sd_ecspi1_pdata __initconst = {
|
|
.chipselect = cpuimx51sd_spi1_cs,
|
|
.num_chipselect = ARRAY_SIZE(cpuimx51sd_spi1_cs),
|
|
};
|
|
|
|
static struct platform_device *rev2_platform_devices[] __initdata = {
|
|
&hsi2c_gpio_device,
|
|
};
|
|
|
|
static const struct imxi2c_platform_data cpuimx51sd_i2c_data __initconst = {
|
|
.bitrate = 100000,
|
|
};
|
|
|
|
static void __init eukrea_cpuimx51sd_init(void)
|
|
{
|
|
imx51_soc_init();
|
|
|
|
mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51sd_pads,
|
|
ARRAY_SIZE(eukrea_cpuimx51sd_pads));
|
|
|
|
imx51_add_imx_uart(0, &uart_pdata);
|
|
imx51_add_mxc_nand(&eukrea_cpuimx51sd_nand_board_info);
|
|
imx51_add_imx2_wdt(0);
|
|
|
|
gpio_request(ETH_RST, "eth_rst");
|
|
gpio_set_value(ETH_RST, 1);
|
|
imx51_add_fec(NULL);
|
|
|
|
gpio_request(CAN_IRQGPIO, "can_irq");
|
|
gpio_direction_input(CAN_IRQGPIO);
|
|
gpio_free(CAN_IRQGPIO);
|
|
gpio_request(CAN_NCS, "can_ncs");
|
|
gpio_direction_output(CAN_NCS, 1);
|
|
gpio_free(CAN_NCS);
|
|
gpio_request(CAN_RST, "can_rst");
|
|
gpio_direction_output(CAN_RST, 0);
|
|
msleep(20);
|
|
gpio_set_value(CAN_RST, 1);
|
|
imx51_add_ecspi(0, &cpuimx51sd_ecspi1_pdata);
|
|
cpuimx51sd_spi_device[0].irq = gpio_to_irq(CAN_IRQGPIO);
|
|
spi_register_board_info(cpuimx51sd_spi_device,
|
|
ARRAY_SIZE(cpuimx51sd_spi_device));
|
|
|
|
if (mx51_revision() < IMX_CHIP_REVISION_3_0) {
|
|
eukrea_cpuimx51sd_i2c_devices[1].irq =
|
|
gpio_to_irq(TSC2007_IRQGPIO_REV2),
|
|
platform_add_devices(rev2_platform_devices,
|
|
ARRAY_SIZE(rev2_platform_devices));
|
|
gpio_request(TSC2007_IRQGPIO_REV2, "tsc2007_irq");
|
|
gpio_direction_input(TSC2007_IRQGPIO_REV2);
|
|
gpio_free(TSC2007_IRQGPIO_REV2);
|
|
} else {
|
|
eukrea_cpuimx51sd_i2c_devices[1].irq =
|
|
gpio_to_irq(TSC2007_IRQGPIO_REV3),
|
|
imx51_add_imx_i2c(0, &cpuimx51sd_i2c_data);
|
|
gpio_request(TSC2007_IRQGPIO_REV3, "tsc2007_irq");
|
|
gpio_direction_input(TSC2007_IRQGPIO_REV3);
|
|
gpio_free(TSC2007_IRQGPIO_REV3);
|
|
}
|
|
|
|
i2c_register_board_info(0, eukrea_cpuimx51sd_i2c_devices,
|
|
ARRAY_SIZE(eukrea_cpuimx51sd_i2c_devices));
|
|
|
|
if (otg_mode_host)
|
|
imx51_add_mxc_ehci_otg(&dr_utmi_config);
|
|
else {
|
|
initialize_otg_port(NULL);
|
|
imx51_add_fsl_usb2_udc(&usb_pdata);
|
|
}
|
|
|
|
gpio_request(USBH1_RST, "usb_rst");
|
|
gpio_direction_output(USBH1_RST, 0);
|
|
msleep(20);
|
|
gpio_set_value(USBH1_RST, 1);
|
|
imx51_add_mxc_ehci_hs(1, &usbh1_config);
|
|
|
|
#ifdef CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD
|
|
eukrea_mbimxsd51_baseboard_init();
|
|
#endif
|
|
}
|
|
|
|
static void __init eukrea_cpuimx51sd_timer_init(void)
|
|
{
|
|
mx51_clocks_init(32768, 24000000, 22579200, 0);
|
|
}
|
|
|
|
MACHINE_START(EUKREA_CPUIMX51SD, "Eukrea CPUIMX51SD")
|
|
/* Maintainer: Eric Bénard <eric@eukrea.com> */
|
|
.atag_offset = 0x100,
|
|
.map_io = mx51_map_io,
|
|
.init_early = imx51_init_early,
|
|
.init_irq = mx51_init_irq,
|
|
.handle_irq = imx51_handle_irq,
|
|
.init_time = eukrea_cpuimx51sd_timer_init,
|
|
.init_machine = eukrea_cpuimx51sd_init,
|
|
.init_late = imx51_init_late,
|
|
.restart = mxc_restart,
|
|
MACHINE_END
|