mirror of
https://github.com/torvalds/linux.git
synced 2024-12-22 10:56:40 +00:00
e764df6796
Per review feedback from Lars-Peter Clausen <lars@metafoo.de> Changes since V1: Fix return value handling of adf4350_parse_dt() Use of_get_gpio Avoid abbreviations in devicetree properties Fix typo in docs Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
87 lines
3.1 KiB
Plaintext
87 lines
3.1 KiB
Plaintext
Analog Devices ADF4350/ADF4351 device driver
|
|
|
|
Required properties:
|
|
- compatible: Should be one of
|
|
* "adi,adf4350": When using the ADF4350 device
|
|
* "adi,adf4351": When using the ADF4351 device
|
|
- reg: SPI chip select numbert for the device
|
|
- spi-max-frequency: Max SPI frequency to use (< 20000000)
|
|
- clocks: From common clock binding. Clock is phandle to clock for
|
|
ADF435x Reference Clock (CLKIN).
|
|
|
|
Optional properties:
|
|
- gpios: GPIO Lock detect - If set with a valid phandle and GPIO number,
|
|
pll lock state is tested upon read.
|
|
- adi,channel-spacing: Channel spacing in Hz (influences MODULUS).
|
|
- adi,power-up-frequency: If set in Hz the PLL tunes to
|
|
the desired frequency on probe.
|
|
- adi,reference-div-factor: If set the driver skips dynamic calculation
|
|
and uses this default value instead.
|
|
- adi,reference-doubler-enable: Enables reference doubler.
|
|
- adi,reference-div2-enable: Enables reference divider.
|
|
- adi,phase-detector-polarity-positive-enable: Enables positive phase
|
|
detector polarity. Default = negative.
|
|
- adi,lock-detect-precision-6ns-enable: Enables 6ns lock detect precision.
|
|
Default = 10ns.
|
|
- adi,lock-detect-function-integer-n-enable: Enables lock detect
|
|
for integer-N mode. Default = factional-N mode.
|
|
- adi,charge-pump-current: Charge pump current in mA.
|
|
Default = 2500mA.
|
|
- adi,muxout-select: On chip multiplexer output selection.
|
|
Valid values for the multiplexer output are:
|
|
0: Three-State Output (default)
|
|
1: DVDD
|
|
2: DGND
|
|
3: R-Counter output
|
|
4: N-Divider output
|
|
5: Analog lock detect
|
|
6: Digital lock detect
|
|
- adi,low-spur-mode-enable: Enables low spur mode.
|
|
Default = Low noise mode.
|
|
- adi,cycle-slip-reduction-enable: Enables cycle slip reduction.
|
|
- adi,charge-cancellation-enable: Enabled charge pump
|
|
charge cancellation for integer-N modes.
|
|
- adi,anti-backlash-3ns-enable: Enables 3ns antibacklash pulse width
|
|
for integer-N modes.
|
|
- adi,band-select-clock-mode-high-enable: Enables faster band
|
|
selection logic.
|
|
- adi,12bit-clk-divider: Clock divider value used when
|
|
adi,12bit-clkdiv-mode != 0
|
|
- adi,clk-divider-mode:
|
|
Valid values for the clkdiv mode are:
|
|
0: Clock divider off (default)
|
|
1: Fast lock enable
|
|
2: Phase resync enable
|
|
- adi,aux-output-enable: Enables auxiliary RF output.
|
|
- adi,aux-output-fundamental-enable: Selects fundamental VCO output on
|
|
the auxiliary RF output. Default = Output of RF dividers.
|
|
- adi,mute-till-lock-enable: Enables Mute-Till-Lock-Detect function.
|
|
- adi,output-power: Output power selection.
|
|
Valid values for the power mode are:
|
|
0: -4dBm (default)
|
|
1: -1dBm
|
|
2: +2dBm
|
|
3: +5dBm
|
|
- adi,aux-output-power: Auxiliary output power selection.
|
|
Valid values for the power mode are:
|
|
0: -4dBm (default)
|
|
1: -1dBm
|
|
2: +2dBm
|
|
3: +5dBm
|
|
|
|
|
|
Example:
|
|
lo_pll0_rx_adf4351: adf4351-rx-lpc@4 {
|
|
compatible = "adi,adf4351";
|
|
reg = <4>;
|
|
spi-max-frequency = <10000000>;
|
|
clocks = <&clk0_ad9523 9>;
|
|
clock-names = "clkin";
|
|
adi,channel-spacing = <10000>;
|
|
adi,power-up-frequency = <2400000000>;
|
|
adi,phase-detector-polarity-positive-enable;
|
|
adi,charge-pump-current = <2500>;
|
|
adi,output-power = <3>;
|
|
adi,mute-till-lock-enable;
|
|
};
|