mirror of
https://github.com/torvalds/linux.git
synced 2024-12-25 04:11:49 +00:00
458f3933bb
The Keystone arch has compatible nand device, so reuse it. In case with Keystone it depends on TI_AEMIF because AEMIF driver is responsible to set timings. See http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Taras Kondratiuk <taras@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
95 lines
2.7 KiB
Plaintext
95 lines
2.7 KiB
Plaintext
Device tree bindings for Texas instruments Davinci/Keystone NAND controller
|
||
|
||
This file provides information, what the device node for the davinci/keystone
|
||
NAND interface contains.
|
||
|
||
Documentation:
|
||
Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
|
||
Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
|
||
|
||
Required properties:
|
||
|
||
- compatible: "ti,davinci-nand"
|
||
"ti,keystone-nand"
|
||
|
||
- reg: Contains 2 offset/length values:
|
||
- offset and length for the access window.
|
||
- offset and length for accessing the AEMIF
|
||
control registers.
|
||
|
||
- ti,davinci-chipselect: number of chipselect. Indicates on the
|
||
davinci_nand driver which chipselect is used
|
||
for accessing the nand.
|
||
Can be in the range [0-3].
|
||
|
||
Recommended properties :
|
||
|
||
- ti,davinci-mask-ale: mask for ALE. Needed for executing address
|
||
phase. These offset will be added to the base
|
||
address for the chip select space the NAND Flash
|
||
device is connected to.
|
||
If not set equal to 0x08.
|
||
|
||
- ti,davinci-mask-cle: mask for CLE. Needed for executing command
|
||
phase. These offset will be added to the base
|
||
address for the chip select space the NAND Flash
|
||
device is connected to.
|
||
If not set equal to 0x10.
|
||
|
||
- ti,davinci-mask-chipsel: mask for chipselect address. Needed to mask
|
||
addresses for given chipselect.
|
||
|
||
- nand-ecc-mode: operation mode of the NAND ecc mode. ECC mode
|
||
valid values for davinci driver:
|
||
- "none"
|
||
- "soft"
|
||
- "hw"
|
||
|
||
- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
|
||
|
||
- nand-bus-width: buswidth 8 or 16. If not present 8.
|
||
|
||
- nand-on-flash-bbt: use flash based bad block table support. OOB
|
||
identifier is saved in OOB area. If not present
|
||
false.
|
||
|
||
Deprecated properties:
|
||
|
||
- ti,davinci-ecc-mode: operation mode of the NAND ecc mode. ECC mode
|
||
valid values for davinci driver:
|
||
- "none"
|
||
- "soft"
|
||
- "hw"
|
||
|
||
- ti,davinci-nand-buswidth: buswidth 8 or 16. If not present 8.
|
||
|
||
- ti,davinci-nand-use-bbt: use flash based bad block table support. OOB
|
||
identifier is saved in OOB area. If not present
|
||
false.
|
||
|
||
Nand device bindings may contain additional sub-nodes describing partitions of
|
||
the address space. See partition.txt for more detail. The NAND Flash timing
|
||
values must be programmed in the chip select’s node of AEMIF
|
||
memory-controller (see Documentation/devicetree/bindings/memory-controllers/
|
||
davinci-aemif.txt).
|
||
|
||
Example(da850 EVM ):
|
||
|
||
nand_cs3@62000000 {
|
||
compatible = "ti,davinci-nand";
|
||
reg = <0x62000000 0x807ff
|
||
0x68000000 0x8000>;
|
||
ti,davinci-chipselect = <1>;
|
||
ti,davinci-mask-ale = <0>;
|
||
ti,davinci-mask-cle = <0>;
|
||
ti,davinci-mask-chipsel = <0>;
|
||
nand-ecc-mode = "hw";
|
||
ti,davinci-ecc-bits = <4>;
|
||
nand-on-flash-bbt;
|
||
|
||
partition@180000 {
|
||
label = "ubifs";
|
||
reg = <0x180000 0x7e80000>;
|
||
};
|
||
};
|