mirror of
https://github.com/torvalds/linux.git
synced 2024-12-27 13:22:23 +00:00
1d1a77ddc8
Four different drivers define the "default-state" property. Move this into the common.txt common LEDs properties. Cc: devicetree@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
320 lines
8.3 KiB
Plaintext
320 lines
8.3 KiB
Plaintext
LEDs connected to Broadcom BCM6328 controller
|
|
|
|
This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268.
|
|
In these SoCs it's possible to control LEDs both as GPIOs or by hardware.
|
|
However, on some devices there are Serial LEDs (LEDs connected to a 74x164
|
|
controller), which can either be controlled by software (exporting the 74x164
|
|
as spi-gpio. See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or
|
|
by hardware using this driver.
|
|
Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and
|
|
exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
|
|
controlled, so the only chance to keep them working is by using this driver.
|
|
|
|
BCM6328 LED controller has a HWDIS register, which controls whether a LED
|
|
should be controlled by a hardware signal instead of the MODE register value,
|
|
with 0 meaning hardware control enabled and 1 hardware control disabled. This
|
|
is usually 1:1 for hardware to LED signals, but through the activity/link
|
|
registers you have some limited control over rerouting the LEDs (as
|
|
explained later in brcm,link-signal-sources). Even if a LED is hardware
|
|
controlled you are still able to make it blink or light it up if it isn't,
|
|
but you can't turn it off if the hardware decides to light it up. For this
|
|
reason, hardware controlled LEDs aren't registered as LED class devices.
|
|
|
|
Required properties:
|
|
- compatible : should be "brcm,bcm6328-leds".
|
|
- #address-cells : must be 1.
|
|
- #size-cells : must be 0.
|
|
- reg : BCM6328 LED controller address and size.
|
|
|
|
Optional properties:
|
|
- brcm,serial-leds : Boolean, enables Serial LEDs.
|
|
Default : false
|
|
- brcm,serial-mux : Boolean, enables Serial LEDs multiplexing.
|
|
Default : false
|
|
- brcm,serial-clk-low : Boolean, makes clock signal active low.
|
|
Default : false
|
|
- brcm,serial-dat-low : Boolean, makes data signal active low.
|
|
Default : false
|
|
- brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction.
|
|
Default : false
|
|
|
|
Each LED is represented as a sub-node of the brcm,bcm6328-leds device.
|
|
|
|
LED sub-node required properties:
|
|
- reg : LED pin number (only LEDs 0 to 23 are valid).
|
|
|
|
LED sub-node optional properties:
|
|
a) Optional properties for sub-nodes related to software controlled LEDs:
|
|
- label : see Documentation/devicetree/bindings/leds/common.txt
|
|
- active-low : Boolean, makes LED active low.
|
|
Default : false
|
|
- default-state : see
|
|
Documentation/devicetree/bindings/leds/common.txt
|
|
- linux,default-trigger : see
|
|
Documentation/devicetree/bindings/leds/common.txt
|
|
|
|
b) Optional properties for sub-nodes related to hardware controlled LEDs:
|
|
- brcm,hardware-controlled : Boolean, makes this LED hardware controlled.
|
|
Default : false
|
|
- brcm,link-signal-sources : An array of hardware link
|
|
signal sources. Up to four link hardware signals can get muxed into
|
|
these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
|
|
be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
|
|
4 to 7. A signal can be muxed to more than one LED, and one LED can
|
|
have more than one source signal.
|
|
- brcm,activity-signal-sources : An array of hardware activity
|
|
signal sources. Up to four activity hardware signals can get muxed into
|
|
these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
|
|
be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
|
|
4 to 7. A signal can be muxed to more than one LED, and one LED can
|
|
have more than one source signal.
|
|
|
|
Examples:
|
|
Scenario 1 : BCM6328 with 4 EPHY LEDs
|
|
leds0: led-controller@10000800 {
|
|
compatible = "brcm,bcm6328-leds";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x10000800 0x24>;
|
|
|
|
alarm_red@2 {
|
|
reg = <2>;
|
|
active-low;
|
|
label = "red:alarm";
|
|
};
|
|
inet_green@3 {
|
|
reg = <3>;
|
|
active-low;
|
|
label = "green:inet";
|
|
};
|
|
power_green@4 {
|
|
reg = <4>;
|
|
active-low;
|
|
label = "green:power";
|
|
default-state = "on";
|
|
};
|
|
ephy0_spd@17 {
|
|
reg = <17>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
ephy1_spd@18 {
|
|
reg = <18>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
ephy2_spd@19 {
|
|
reg = <19>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
ephy3_spd@20 {
|
|
reg = <20>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
};
|
|
|
|
Scenario 2 : BCM63268 with Serial/GPHY0 LEDs
|
|
leds0: led-controller@10001900 {
|
|
compatible = "brcm,bcm6328-leds";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x10001900 0x24>;
|
|
brcm,serial-leds;
|
|
brcm,serial-dat-low;
|
|
brcm,serial-shift-inv;
|
|
|
|
gphy0_spd0@0 {
|
|
reg = <0>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <0>;
|
|
};
|
|
gphy0_spd1@1 {
|
|
reg = <1>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <1>;
|
|
};
|
|
inet_red@2 {
|
|
reg = <2>;
|
|
active-low;
|
|
label = "red:inet";
|
|
};
|
|
dsl_green@3 {
|
|
reg = <3>;
|
|
active-low;
|
|
label = "green:dsl";
|
|
};
|
|
usb_green@4 {
|
|
reg = <4>;
|
|
active-low;
|
|
label = "green:usb";
|
|
};
|
|
wps_green@7 {
|
|
reg = <7>;
|
|
active-low;
|
|
label = "green:wps";
|
|
};
|
|
inet_green@8 {
|
|
reg = <8>;
|
|
active-low;
|
|
label = "green:inet";
|
|
};
|
|
ephy0_act@9 {
|
|
reg = <9>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
ephy1_act@10 {
|
|
reg = <10>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
ephy2_act@11 {
|
|
reg = <11>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
gphy0_act@12 {
|
|
reg = <12>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
ephy0_spd@13 {
|
|
reg = <13>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
ephy1_spd@14 {
|
|
reg = <14>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
ephy2_spd@15 {
|
|
reg = <15>;
|
|
brcm,hardware-controlled;
|
|
};
|
|
power_green@20 {
|
|
reg = <20>;
|
|
active-low;
|
|
label = "green:power";
|
|
default-state = "on";
|
|
};
|
|
};
|
|
|
|
Scenario 3 : BCM6362 with 1 LED for each EPHY
|
|
leds0: led-controller@10001900 {
|
|
compatible = "brcm,bcm6328-leds";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x10001900 0x24>;
|
|
|
|
usb@0 {
|
|
reg = <0>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <0>;
|
|
brcm,activity-signal-sources = <0>;
|
|
/* USB link/activity routed to USB LED */
|
|
};
|
|
inet@1 {
|
|
reg = <1>;
|
|
brcm,hardware-controlled;
|
|
brcm,activity-signal-sources = <1>;
|
|
/* INET activity routed to INET LED */
|
|
};
|
|
ephy0@4 {
|
|
reg = <4>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <4>;
|
|
/* EPHY0 link routed to EPHY0 LED */
|
|
};
|
|
ephy1@5 {
|
|
reg = <5>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <5>;
|
|
/* EPHY1 link routed to EPHY1 LED */
|
|
};
|
|
ephy2@6 {
|
|
reg = <6>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <6>;
|
|
/* EPHY2 link routed to EPHY2 LED */
|
|
};
|
|
ephy3@7 {
|
|
reg = <7>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <7>;
|
|
/* EPHY3 link routed to EPHY3 LED */
|
|
};
|
|
power_green@20 {
|
|
reg = <20>;
|
|
active-low;
|
|
label = "green:power";
|
|
default-state = "on";
|
|
};
|
|
};
|
|
|
|
Scenario 4 : BCM6362 with 1 LED for all EPHYs
|
|
leds0: led-controller@10001900 {
|
|
compatible = "brcm,bcm6328-leds";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x10001900 0x24>;
|
|
|
|
usb@0 {
|
|
reg = <0>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <0 1>;
|
|
brcm,activity-signal-sources = <0 1>;
|
|
/* USB/INET link/activity routed to USB LED */
|
|
};
|
|
ephy@4 {
|
|
reg = <4>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <4 5 6 7>;
|
|
/* EPHY0/1/2/3 link routed to EPHY0 LED */
|
|
};
|
|
power_green@20 {
|
|
reg = <20>;
|
|
active-low;
|
|
label = "green:power";
|
|
default-state = "on";
|
|
};
|
|
};
|
|
|
|
Scenario 5 : BCM6362 with EPHY LEDs swapped
|
|
leds0: led-controller@10001900 {
|
|
compatible = "brcm,bcm6328-leds";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x10001900 0x24>;
|
|
|
|
usb@0 {
|
|
reg = <0>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <0>;
|
|
brcm,activity-signal-sources = <0 1>;
|
|
/* USB link/act and INET act routed to USB LED */
|
|
};
|
|
ephy0@4 {
|
|
reg = <4>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <7>;
|
|
/* EPHY3 link routed to EPHY0 LED */
|
|
};
|
|
ephy1@5 {
|
|
reg = <5>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <6>;
|
|
/* EPHY2 link routed to EPHY1 LED */
|
|
};
|
|
ephy2@6 {
|
|
reg = <6>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <5>;
|
|
/* EPHY1 link routed to EPHY2 LED */
|
|
};
|
|
ephy3@7 {
|
|
reg = <7>;
|
|
brcm,hardware-controlled;
|
|
brcm,link-signal-sources = <4>;
|
|
/* EPHY0 link routed to EPHY3 LED */
|
|
};
|
|
power_green@20 {
|
|
reg = <20>;
|
|
active-low;
|
|
label = "green:power";
|
|
default-state = "on";
|
|
};
|
|
};
|