mirror of
https://github.com/torvalds/linux.git
synced 2024-12-29 14:21:47 +00:00
ca784be36c
Start using the control module driver for powering on the PHY and for writing to the mailbox instead of writing to the control module registers on their own. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
66 lines
2.3 KiB
Plaintext
66 lines
2.3 KiB
Plaintext
OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
|
|
|
|
OMAP MUSB GLUE
|
|
- compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
|
|
- ti,hwmods : must be "usb_otg_hs"
|
|
- ti,has-mailbox : to specify that omap uses an external mailbox
|
|
(in control module) to communicate with the musb core during device connect
|
|
and disconnect.
|
|
- multipoint : Should be "1" indicating the musb controller supports
|
|
multipoint. This is a MUSB configuration-specific setting.
|
|
- num_eps : Specifies the number of endpoints. This is also a
|
|
MUSB configuration-specific setting. Should be set to "16"
|
|
- ram_bits : Specifies the ram address size. Should be set to "12"
|
|
- interface_type : This is a board specific setting to describe the type of
|
|
interface between the controller and the phy. It should be "0" or "1"
|
|
specifying ULPI and UTMI respectively.
|
|
- mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
|
|
represents PERIPHERAL.
|
|
- power : Should be "50". This signifies the controller can supply upto
|
|
100mA when operating in host mode.
|
|
|
|
Optional properties:
|
|
- ctrl-module : phandle of the control module this glue uses to write to
|
|
mailbox
|
|
|
|
SOC specific device node entry
|
|
usb_otg_hs: usb_otg_hs@4a0ab000 {
|
|
compatible = "ti,omap4-musb";
|
|
ti,hwmods = "usb_otg_hs";
|
|
ti,has-mailbox;
|
|
multipoint = <1>;
|
|
num_eps = <16>;
|
|
ram_bits = <12>;
|
|
ctrl-module = <&omap_control_usb>;
|
|
};
|
|
|
|
Board specific device node entry
|
|
&usb_otg_hs {
|
|
interface_type = <1>;
|
|
mode = <3>;
|
|
power = <50>;
|
|
};
|
|
|
|
OMAP CONTROL USB
|
|
|
|
Required properties:
|
|
- compatible: Should be "ti,omap-control-usb"
|
|
- reg : Address and length of the register set for the device. It contains
|
|
the address of "control_dev_conf" and "otghs_control" or "phy_power_usb"
|
|
depending upon omap4 or omap5.
|
|
- reg-names: The names of the register addresses corresponding to the registers
|
|
filled in "reg".
|
|
- ti,type: This is used to differentiate whether the control module has
|
|
usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to
|
|
notify events to the musb core and omap5 has usb3 phy power register to
|
|
power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3
|
|
phy power.
|
|
|
|
omap_control_usb: omap-control-usb@4a002300 {
|
|
compatible = "ti,omap-control-usb";
|
|
reg = <0x4a002300 0x4>,
|
|
<0x4a00233c 0x4>;
|
|
reg-names = "control_dev_conf", "otghs_control";
|
|
ti,type = <1>;
|
|
};
|