mirror of
https://github.com/torvalds/linux.git
synced 2024-12-29 14:21:47 +00:00
f21ccfa070
Correct spelling typos within Documentation/devicetree Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
60 lines
2.3 KiB
Plaintext
60 lines
2.3 KiB
Plaintext
* Samsung's SDHCI Controller device tree bindings
|
|
|
|
Samsung's SDHCI controller is used as a connectivity interface with external
|
|
MMC, SD and eMMC storage mediums. This file documents differences between the
|
|
core mmc properties described by mmc.txt and the properties used by the
|
|
Samsung implmentation of the SDHCI controller.
|
|
|
|
Note: The mmc core bindings documentation states that if none of the core
|
|
card-detect bindings are used, then the standard sdhci card detect mechanism
|
|
is used. The Samsung's SDHCI controller bindings extends this as listed below.
|
|
|
|
[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the
|
|
"Optional Board Specific Properties" section below.
|
|
|
|
Required SoC Specific Properties:
|
|
- compatible: should be one of the following
|
|
- "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci
|
|
controller.
|
|
- "samsung,exynos4210-sdhci": For controllers compatible with Exynos4 sdhci
|
|
controller.
|
|
|
|
Required Board Specific Properties:
|
|
- Samsung GPIO variant (will be completely replaced by pinctrl):
|
|
- gpios: Should specify the gpios used for clock, command and data lines. The
|
|
gpio specifier format depends on the gpio controller.
|
|
- Pinctrl variant (preferred if available):
|
|
- pinctrl-0: Should specify pin control groups used for this controller.
|
|
- pinctrl-names: Should contain only one value - "default".
|
|
|
|
Optional Board Specific Properties:
|
|
- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed
|
|
through a pinmux to the card-detect pin of the card slot. This property
|
|
should be used only if none of the mmc core card-detect properties are
|
|
used. Only for Samsung GPIO variant.
|
|
|
|
Example:
|
|
sdhci@12530000 {
|
|
compatible = "samsung,exynos4210-sdhci";
|
|
reg = <0x12530000 0x100>;
|
|
interrupts = <0 75 0>;
|
|
bus-width = <4>;
|
|
cd-gpios = <&gpk2 2 2 3 3>;
|
|
|
|
/* Samsung GPIO variant */
|
|
gpios = <&gpk2 0 2 0 3>, /* clock line */
|
|
<&gpk2 1 2 0 3>, /* command line */
|
|
<&gpk2 3 2 3 3>, /* data line 0 */
|
|
<&gpk2 4 2 3 3>, /* data line 1 */
|
|
<&gpk2 5 2 3 3>, /* data line 2 */
|
|
<&gpk2 6 2 3 3>; /* data line 3 */
|
|
|
|
/* Pinctrl variant */
|
|
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
Note: This example shows both SoC specific and board specific properties
|
|
in a single device node. The properties can be actually be separated
|
|
into SoC specific node and board specific node.
|