Minki/linux
1
0
Fork 1
mirror of https://github.com/torvalds/linux.git synced 2024-12-15 23:51:46 +00:00
Code Issues Packages Projects Releases Wiki Activity
1fe0e1fa32
linux/drivers/tty/serial/8250/8250_port.c
Maciej W. Rozycki d7aff291d0 serial: 8250: Define RX trigger levels for OxSemi 950 devices 
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120.  This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.

For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable.  Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.

Lower the default receive interrupt trigger level to 32 then, and make
it configurable.  Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].

References:

[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
    Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
    Levels", p. 22

[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22

Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-27 12:05:46 +02:00

3444 lines
87 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0+
/*
* Base port operations for 8250/16550-type serial ports
*
* Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
* Split from 8250_core.c, Copyright (C) 2001 Russell King.
*
* A note about mapbase / membase
*
* mapbase is the physical address of the IO port.
* membase is an 'ioremapped' cookie.
*/
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/gpio/consumer.h>
#include <linux/sysrq.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/tty.h>
#include <linux/ratelimit.h>
#include <linux/tty_flip.h>
#include <linux/serial.h>
#include <linux/serial_8250.h>
#include <linux/nmi.h>
#include <linux/mutex.h>
#include <linux/slab.h>
#include <linux/uaccess.h>
#include <linux/pm_runtime.h>
#include <linux/ktime.h>
#include <asm/io.h>
#include <asm/irq.h>
#include "8250.h"
/* Nuvoton NPCM timeout register */
#define UART_NPCM_TOR 7
#define UART_NPCM_TOIE BIT(7) /* Timeout Interrupt Enable */
/*
* Debugging.
*/
#if 0
#define DEBUG_AUTOCONF(fmt...) printk(fmt)
#else
#define DEBUG_AUTOCONF(fmt...) do { } while (0)
#endif
#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
/*
* Here we define the default xmit fifo size used for each type of UART.
*/
static const struct serial8250_config uart_config[] = {
[PORT_UNKNOWN] = {
.name = "unknown",
.fifo_size = 1,
.tx_loadsz = 1,
},
[PORT_8250] = {
.name = "8250",
.fifo_size = 1,
.tx_loadsz = 1,
},
[PORT_16450] = {
.name = "16450",
.fifo_size = 1,
.tx_loadsz = 1,
},
[PORT_16550] = {
.name = "16550",
.fifo_size = 1,
.tx_loadsz = 1,
},
[PORT_16550A] = {
.name = "16550A",
.fifo_size = 16,
.tx_loadsz = 16,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.rxtrig_bytes = {1, 4, 8, 14},
.flags = UART_CAP_FIFO,
},
[PORT_CIRRUS] = {
.name = "Cirrus",
.fifo_size = 1,
.tx_loadsz = 1,
},
[PORT_16650] = {
.name = "ST16650",
.fifo_size = 1,
.tx_loadsz = 1,
.flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
},
[PORT_16650V2] = {
.name = "ST16650V2",
.fifo_size = 32,
.tx_loadsz = 16,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
UART_FCR_T_TRIG_00,
.rxtrig_bytes = {8, 16, 24, 28},
.flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
},
[PORT_16750] = {
.name = "TI16750",
.fifo_size = 64,
.tx_loadsz = 64,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
UART_FCR7_64BYTE,
.rxtrig_bytes = {1, 16, 32, 56},
.flags = UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE,
},
[PORT_STARTECH] = {
.name = "Startech",
.fifo_size = 1,
.tx_loadsz = 1,
},
[PORT_16C950] = {
.name = "16C950/954",
.fifo_size = 128,
.tx_loadsz = 128,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01,
.rxtrig_bytes = {16, 32, 112, 120},
/* UART_CAP_EFR breaks billionon CF bluetooth card. */
.flags = UART_CAP_FIFO | UART_CAP_SLEEP,
},
[PORT_16654] = {
.name = "ST16654",
.fifo_size = 64,
.tx_loadsz = 32,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
UART_FCR_T_TRIG_10,
.rxtrig_bytes = {8, 16, 56, 60},
.flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
},
[PORT_16850] = {
.name = "XR16850",
.fifo_size = 128,
.tx_loadsz = 128,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
},
[PORT_RSA] = {
.name = "RSA",
.fifo_size = 2048,
.tx_loadsz = 2048,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11,
.flags = UART_CAP_FIFO,
},
[PORT_NS16550A] = {
.name = "NS16550A",
.fifo_size = 16,
.tx_loadsz = 16,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_NATSEMI,
},
[PORT_XSCALE] = {
.name = "XScale",
.fifo_size = 32,
.tx_loadsz = 32,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE,
},
[PORT_OCTEON] = {
.name = "OCTEON",
.fifo_size = 64,
.tx_loadsz = 64,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO,
},
[PORT_AR7] = {
.name = "AR7",
.fifo_size = 16,
.tx_loadsz = 16,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00,
.flags = UART_CAP_FIFO /* | UART_CAP_AFE */,
},
[PORT_U6_16550A] = {
.name = "U6_16550A",
.fifo_size = 64,
.tx_loadsz = 64,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_AFE,
},
[PORT_TEGRA] = {
.name = "Tegra",
.fifo_size = 32,
.tx_loadsz = 8,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
UART_FCR_T_TRIG_01,
.rxtrig_bytes = {1, 4, 8, 14},
.flags = UART_CAP_FIFO | UART_CAP_RTOIE,
},
[PORT_XR17D15X] = {
.name = "XR17D15X",
.fifo_size = 64,
.tx_loadsz = 64,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
UART_CAP_SLEEP,
},
[PORT_XR17V35X] = {
.name = "XR17V35X",
.fifo_size = 256,
.tx_loadsz = 256,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 |
UART_FCR_T_TRIG_11,
.flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
UART_CAP_SLEEP,
},
[PORT_LPC3220] = {
.name = "LPC3220",
.fifo_size = 64,
.tx_loadsz = 32,
.fcr = UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO |
UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00,
.flags = UART_CAP_FIFO,
},
[PORT_BRCM_TRUMANAGE] = {
.name = "TruManage",
.fifo_size = 1,
.tx_loadsz = 1024,
.flags = UART_CAP_HFIFO,
},
[PORT_8250_CIR] = {
.name = "CIR port"
},
[PORT_ALTR_16550_F32] = {
.name = "Altera 16550 FIFO32",
.fifo_size = 32,
.tx_loadsz = 32,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.rxtrig_bytes = {1, 8, 16, 30},
.flags = UART_CAP_FIFO | UART_CAP_AFE,
},
[PORT_ALTR_16550_F64] = {
.name = "Altera 16550 FIFO64",
.fifo_size = 64,
.tx_loadsz = 64,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.rxtrig_bytes = {1, 16, 32, 62},
.flags = UART_CAP_FIFO | UART_CAP_AFE,
},
[PORT_ALTR_16550_F128] = {
.name = "Altera 16550 FIFO128",
.fifo_size = 128,
.tx_loadsz = 128,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.rxtrig_bytes = {1, 32, 64, 126},
.flags = UART_CAP_FIFO | UART_CAP_AFE,
},
/*
* tx_loadsz is set to 63-bytes instead of 64-bytes to implement
* workaround of errata A-008006 which states that tx_loadsz should
* be configured less than Maximum supported fifo bytes.
*/
[PORT_16550A_FSL64] = {
.name = "16550A_FSL64",
.fifo_size = 64,
.tx_loadsz = 63,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
UART_FCR7_64BYTE,
.flags = UART_CAP_FIFO,
},
[PORT_RT2880] = {
.name = "Palmchip BK-3103",
.fifo_size = 16,
.tx_loadsz = 16,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.rxtrig_bytes = {1, 4, 8, 14},
.flags = UART_CAP_FIFO,
},
[PORT_DA830] = {
.name = "TI DA8xx/66AK2x",
.fifo_size = 16,
.tx_loadsz = 16,
.fcr = UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO |
UART_FCR_R_TRIG_10,
.rxtrig_bytes = {1, 4, 8, 14},
.flags = UART_CAP_FIFO | UART_CAP_AFE,
},
[PORT_MTK_BTIF] = {
.name = "MediaTek BTIF",
.fifo_size = 16,
.tx_loadsz = 16,
.fcr = UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
.flags = UART_CAP_FIFO,
},
[PORT_NPCM] = {
.name = "Nuvoton 16550",
.fifo_size = 16,
.tx_loadsz = 16,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
.rxtrig_bytes = {1, 4, 8, 14},
.flags = UART_CAP_FIFO,
},
[PORT_SUNIX] = {
.name = "Sunix",
.fifo_size = 128,
.tx_loadsz = 128,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.rxtrig_bytes = {1, 32, 64, 112},
.flags = UART_CAP_FIFO | UART_CAP_SLEEP,
},
};
/* Uart divisor latch read */
static int default_serial_dl_read(struct uart_8250_port *up)
{
return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8;
}
/* Uart divisor latch write */
static void default_serial_dl_write(struct uart_8250_port *up, int value)
{
serial_out(up, UART_DLL, value & 0xff);
serial_out(up, UART_DLM, value >> 8 & 0xff);
}
#ifdef CONFIG_SERIAL_8250_RT288X
/* Au1x00/RT288x UART hardware has a weird register layout */
static const s8 au_io_in_map[8] = {
0, /* UART_RX */
2, /* UART_IER */
3, /* UART_IIR */
5, /* UART_LCR */
6, /* UART_MCR */
7, /* UART_LSR */
8, /* UART_MSR */
-1, /* UART_SCR (unmapped) */
};
static const s8 au_io_out_map[8] = {
1, /* UART_TX */
2, /* UART_IER */
4, /* UART_FCR */
5, /* UART_LCR */
6, /* UART_MCR */
-1, /* UART_LSR (unmapped) */
-1, /* UART_MSR (unmapped) */
-1, /* UART_SCR (unmapped) */
};
unsigned int au_serial_in(struct uart_port *p, int offset)
{
if (offset >= ARRAY_SIZE(au_io_in_map))
return UINT_MAX;
offset = au_io_in_map[offset];
if (offset < 0)
return UINT_MAX;
return __raw_readl(p->membase + (offset << p->regshift));
}
void au_serial_out(struct uart_port *p, int offset, int value)
{
if (offset >= ARRAY_SIZE(au_io_out_map))
return;
offset = au_io_out_map[offset];
if (offset < 0)
return;
__raw_writel(value, p->membase + (offset << p->regshift));
}
/* Au1x00 haven't got a standard divisor latch */
static int au_serial_dl_read(struct uart_8250_port *up)
{
return __raw_readl(up->port.membase + 0x28);
}
static void au_serial_dl_write(struct uart_8250_port *up, int value)
{
__raw_writel(value, up->port.membase + 0x28);
}
#endif
static unsigned int hub6_serial_in(struct uart_port *p, int offset)
{
offset = offset << p->regshift;
outb(p->hub6 - 1 + offset, p->iobase);
return inb(p->iobase + 1);
}
static void hub6_serial_out(struct uart_port *p, int offset, int value)
{
offset = offset << p->regshift;
outb(p->hub6 - 1 + offset, p->iobase);
outb(value, p->iobase + 1);
}
static unsigned int mem_serial_in(struct uart_port *p, int offset)
{
offset = offset << p->regshift;
return readb(p->membase + offset);
}
static void mem_serial_out(struct uart_port *p, int offset, int value)
{
offset = offset << p->regshift;
writeb(value, p->membase + offset);
}
static void mem16_serial_out(struct uart_port *p, int offset, int value)
{
offset = offset << p->regshift;
writew(value, p->membase + offset);
}
static unsigned int mem16_serial_in(struct uart_port *p, int offset)
{
offset = offset << p->regshift;
return readw(p->membase + offset);
}
static void mem32_serial_out(struct uart_port *p, int offset, int value)
{
offset = offset << p->regshift;
writel(value, p->membase + offset);
}
static unsigned int mem32_serial_in(struct uart_port *p, int offset)
{
offset = offset << p->regshift;
return readl(p->membase + offset);
}
static void mem32be_serial_out(struct uart_port *p, int offset, int value)
{
offset = offset << p->regshift;
iowrite32be(value, p->membase + offset);
}
static unsigned int mem32be_serial_in(struct uart_port *p, int offset)
{
offset = offset << p->regshift;
return ioread32be(p->membase + offset);
}
static unsigned int io_serial_in(struct uart_port *p, int offset)
{
offset = offset << p->regshift;
return inb(p->iobase + offset);
}
static void io_serial_out(struct uart_port *p, int offset, int value)
{
offset = offset << p->regshift;
outb(value, p->iobase + offset);
}
static int serial8250_default_handle_irq(struct uart_port *port);
static void set_io_from_upio(struct uart_port *p)
{
struct uart_8250_port *up = up_to_u8250p(p);
up->dl_read = default_serial_dl_read;
up->dl_write = default_serial_dl_write;
switch (p->iotype) {
case UPIO_HUB6:
p->serial_in = hub6_serial_in;
p->serial_out = hub6_serial_out;
break;
case UPIO_MEM:
p->serial_in = mem_serial_in;
p->serial_out = mem_serial_out;
break;
case UPIO_MEM16:
p->serial_in = mem16_serial_in;
p->serial_out = mem16_serial_out;
break;
case UPIO_MEM32:
p->serial_in = mem32_serial_in;
p->serial_out = mem32_serial_out;
break;
case UPIO_MEM32BE:
p->serial_in = mem32be_serial_in;
p->serial_out = mem32be_serial_out;
break;
#ifdef CONFIG_SERIAL_8250_RT288X
case UPIO_AU:
p->serial_in = au_serial_in;
p->serial_out = au_serial_out;
up->dl_read = au_serial_dl_read;
up->dl_write = au_serial_dl_write;
break;
#endif
default:
p->serial_in = io_serial_in;
p->serial_out = io_serial_out;
break;
}
/* Remember loaded iotype */
up->cur_iotype = p->iotype;
p->handle_irq = serial8250_default_handle_irq;
}
static void
serial_port_out_sync(struct uart_port *p, int offset, int value)
{
switch (p->iotype) {
case UPIO_MEM:
case UPIO_MEM16:
case UPIO_MEM32:
case UPIO_MEM32BE:
case UPIO_AU:
p->serial_out(p, offset, value);
p->serial_in(p, UART_LCR); /* safe, no side-effects */
break;
default:
p->serial_out(p, offset, value);
}
}
/*
* For the 16C950
*/
static void serial_icr_write(struct uart_8250_port *up, int offset, int value)
{
serial_out(up, UART_SCR, offset);
serial_out(up, UART_ICR, value);
}
static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
{
unsigned int value;
serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
serial_out(up, UART_SCR, offset);
value = serial_in(up, UART_ICR);
serial_icr_write(up, UART_ACR, up->acr);
return value;
}
/*
* FIFO support.
*/
static void serial8250_clear_fifos(struct uart_8250_port *p)
{
if (p->capabilities & UART_CAP_FIFO) {
serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
serial_out(p, UART_FCR, 0);
}
}
static enum hrtimer_restart serial8250_em485_handle_start_tx(struct hrtimer *t);
static enum hrtimer_restart serial8250_em485_handle_stop_tx(struct hrtimer *t);
void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p)
{
serial8250_clear_fifos(p);
serial_out(p, UART_FCR, p->fcr);
}
EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos);
void serial8250_rpm_get(struct uart_8250_port *p)
{
if (!(p->capabilities & UART_CAP_RPM))
return;
pm_runtime_get_sync(p->port.dev);
}
EXPORT_SYMBOL_GPL(serial8250_rpm_get);
void serial8250_rpm_put(struct uart_8250_port *p)
{
if (!(p->capabilities & UART_CAP_RPM))
return;
pm_runtime_mark_last_busy(p->port.dev);
pm_runtime_put_autosuspend(p->port.dev);
}
EXPORT_SYMBOL_GPL(serial8250_rpm_put);
/**
* serial8250_em485_init() - put uart_8250_port into rs485 emulating
* @p: uart_8250_port port instance
*
* The function is used to start rs485 software emulating on the
* &struct uart_8250_port* @p. Namely, RTS is switched before/after
* transmission. The function is idempotent, so it is safe to call it
* multiple times.
*
* The caller MUST enable interrupt on empty shift register before
* calling serial8250_em485_init(). This interrupt is not a part of
* 8250 standard, but implementation defined.
*
* The function is supposed to be called from .rs485_config callback
* or from any other callback protected with p->port.lock spinlock.
*
* See also serial8250_em485_destroy()
*
* Return 0 - success, -errno - otherwise
*/
static int serial8250_em485_init(struct uart_8250_port *p)
{
if (p->em485)
return 0;
p->em485 = kmalloc(sizeof(struct uart_8250_em485), GFP_ATOMIC);
if (!p->em485)
return -ENOMEM;
hrtimer_init(&p->em485->stop_tx_timer, CLOCK_MONOTONIC,
HRTIMER_MODE_REL);
hrtimer_init(&p->em485->start_tx_timer, CLOCK_MONOTONIC,
HRTIMER_MODE_REL);
p->em485->stop_tx_timer.function = &serial8250_em485_handle_stop_tx;
p->em485->start_tx_timer.function = &serial8250_em485_handle_start_tx;
p->em485->port = p;
p->em485->active_timer = NULL;
p->em485->tx_stopped = true;
p->rs485_stop_tx(p);
return 0;
}
/**
* serial8250_em485_destroy() - put uart_8250_port into normal state
* @p: uart_8250_port port instance
*
* The function is used to stop rs485 software emulating on the
* &struct uart_8250_port* @p. The function is idempotent, so it is safe to
* call it multiple times.
*
* The function is supposed to be called from .rs485_config callback
* or from any other callback protected with p->port.lock spinlock.
*
* See also serial8250_em485_init()
*/
void serial8250_em485_destroy(struct uart_8250_port *p)
{
if (!p->em485)
return;
hrtimer_cancel(&p->em485->start_tx_timer);
hrtimer_cancel(&p->em485->stop_tx_timer);
kfree(p->em485);
p->em485 = NULL;
}
EXPORT_SYMBOL_GPL(serial8250_em485_destroy);
/**
* serial8250_em485_config() - generic ->rs485_config() callback
* @port: uart port
* @rs485: rs485 settings
*
* Generic callback usable by 8250 uart drivers to activate rs485 settings
* if the uart is incapable of driving RTS as a Transmit Enable signal in
* hardware, relying on software emulation instead.
*/
int serial8250_em485_config(struct uart_port *port, struct serial_rs485 *rs485)
{
struct uart_8250_port *up = up_to_u8250p(port);
/* pick sane settings if the user hasn't */
if (!!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
!!(rs485->flags & SER_RS485_RTS_AFTER_SEND)) {
rs485->flags |= SER_RS485_RTS_ON_SEND;
rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
}
/* clamp the delays to [0, 100ms] */
rs485->delay_rts_before_send = min(rs485->delay_rts_before_send, 100U);
rs485->delay_rts_after_send = min(rs485->delay_rts_after_send, 100U);
memset(rs485->padding, 0, sizeof(rs485->padding));
port->rs485 = *rs485;
gpiod_set_value(port->rs485_term_gpio,
rs485->flags & SER_RS485_TERMINATE_BUS);
/*
* Both serial8250_em485_init() and serial8250_em485_destroy()
* are idempotent.
*/
if (rs485->flags & SER_RS485_ENABLED) {
int ret = serial8250_em485_init(up);
if (ret) {
rs485->flags &= ~SER_RS485_ENABLED;
port->rs485.flags &= ~SER_RS485_ENABLED;
}
return ret;
}
serial8250_em485_destroy(up);
return 0;
}
EXPORT_SYMBOL_GPL(serial8250_em485_config);
/*
* These two wrappers ensure that enable_runtime_pm_tx() can be called more than
* once and disable_runtime_pm_tx() will still disable RPM because the fifo is
* empty and the HW can idle again.
*/
void serial8250_rpm_get_tx(struct uart_8250_port *p)
{
unsigned char rpm_active;
if (!(p->capabilities & UART_CAP_RPM))
return;
rpm_active = xchg(&p->rpm_tx_active, 1);
if (rpm_active)
return;
pm_runtime_get_sync(p->port.dev);
}
EXPORT_SYMBOL_GPL(serial8250_rpm_get_tx);
void serial8250_rpm_put_tx(struct uart_8250_port *p)
{
unsigned char rpm_active;
if (!(p->capabilities & UART_CAP_RPM))
return;
rpm_active = xchg(&p->rpm_tx_active, 0);
if (!rpm_active)
return;
pm_runtime_mark_last_busy(p->port.dev);
pm_runtime_put_autosuspend(p->port.dev);
}
EXPORT_SYMBOL_GPL(serial8250_rpm_put_tx);
/*
* IER sleep support. UARTs which have EFRs need the "extended
* capability" bit enabled. Note that on XR16C850s, we need to
* reset LCR to write to IER.
*/
static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
{
unsigned char lcr = 0, efr = 0;
serial8250_rpm_get(p);
if (p->capabilities & UART_CAP_SLEEP) {
if (p->capabilities & UART_CAP_EFR) {
lcr = serial_in(p, UART_LCR);
efr = serial_in(p, UART_EFR);
serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(p, UART_EFR, UART_EFR_ECB);
serial_out(p, UART_LCR, 0);
}
serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0);
if (p->capabilities & UART_CAP_EFR) {
serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(p, UART_EFR, efr);
serial_out(p, UART_LCR, lcr);
}
}
serial8250_rpm_put(p);
}
#ifdef CONFIG_SERIAL_8250_RSA
/*
* Attempts to turn on the RSA FIFO. Returns zero on failure.
* We set the port uart clock rate if we succeed.
*/
static int __enable_rsa(struct uart_8250_port *up)
{
unsigned char mode;
int result;
mode = serial_in(up, UART_RSA_MSR);
result = mode & UART_RSA_MSR_FIFO;
if (!result) {
serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
mode = serial_in(up, UART_RSA_MSR);
result = mode & UART_RSA_MSR_FIFO;
}
if (result)
up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
return result;
}
static void enable_rsa(struct uart_8250_port *up)
{
if (up->port.type == PORT_RSA) {
if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
spin_lock_irq(&up->port.lock);
__enable_rsa(up);
spin_unlock_irq(&up->port.lock);
}
if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
serial_out(up, UART_RSA_FRR, 0);
}
}
/*
* Attempts to turn off the RSA FIFO. Returns zero on failure.
* It is unknown why interrupts were disabled in here. However,
* the caller is expected to preserve this behaviour by grabbing
* the spinlock before calling this function.
*/
static void disable_rsa(struct uart_8250_port *up)
{
unsigned char mode;
int result;
if (up->port.type == PORT_RSA &&
up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
spin_lock_irq(&up->port.lock);
mode = serial_in(up, UART_RSA_MSR);
result = !(mode & UART_RSA_MSR_FIFO);
if (!result) {
serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
mode = serial_in(up, UART_RSA_MSR);
result = !(mode & UART_RSA_MSR_FIFO);
}
if (result)
up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
spin_unlock_irq(&up->port.lock);
}
}
#endif /* CONFIG_SERIAL_8250_RSA */
/*
* This is a quickie test to see how big the FIFO is.
* It doesn't work at all the time, more's the pity.
*/
static int size_fifo(struct uart_8250_port *up)
{
unsigned char old_fcr, old_mcr, old_lcr;
unsigned short old_dl;
int count;
old_lcr = serial_in(up, UART_LCR);
serial_out(up, UART_LCR, 0);
old_fcr = serial_in(up, UART_FCR);
old_mcr = serial8250_in_MCR(up);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
serial8250_out_MCR(up, UART_MCR_LOOP);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
old_dl = serial_dl_read(up);
serial_dl_write(up, 0x0001);
serial_out(up, UART_LCR, 0x03);
for (count = 0; count < 256; count++)
serial_out(up, UART_TX, count);
mdelay(20);/* FIXME - schedule_timeout */
for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) &&
(count < 256); count++)
serial_in(up, UART_RX);
serial_out(up, UART_FCR, old_fcr);
serial8250_out_MCR(up, old_mcr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_dl_write(up, old_dl);
serial_out(up, UART_LCR, old_lcr);
return count;
}
/*
* Read UART ID using the divisor method - set DLL and DLM to zero
* and the revision will be in DLL and device type in DLM. We
* preserve the device state across this.
*/
static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
{
unsigned char old_lcr;
unsigned int id, old_dl;
old_lcr = serial_in(p, UART_LCR);
serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A);
old_dl = serial_dl_read(p);
serial_dl_write(p, 0);
id = serial_dl_read(p);
serial_dl_write(p, old_dl);
serial_out(p, UART_LCR, old_lcr);
return id;
}
/*
* This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's.
* When this function is called we know it is at least a StarTech
* 16650 V2, but it might be one of several StarTech UARTs, or one of
* its clones. (We treat the broken original StarTech 16650 V1 as a
* 16550, and why not? Startech doesn't seem to even acknowledge its
* existence.)
*
* What evil have men's minds wrought...
*/
static void autoconfig_has_efr(struct uart_8250_port *up)
{
unsigned int id1, id2, id3, rev;
/*
* Everything with an EFR has SLEEP
*/
up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
/*
* First we check to see if it's an Oxford Semiconductor UART.
*
* If we have to do this here because some non-National
* Semiconductor clone chips lock up if you try writing to the
* LSR register (which serial_icr_read does)
*/
/*
* Check for Oxford Semiconductor 16C950.
*
* EFR [4] must be set else this test fails.
*
* This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca)
* claims that it's needed for 952 dual UART's (which are not
* recommended for new designs).
*/
up->acr = 0;
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_EFR, UART_EFR_ECB);
serial_out(up, UART_LCR, 0x00);
id1 = serial_icr_read(up, UART_ID1);
id2 = serial_icr_read(up, UART_ID2);
id3 = serial_icr_read(up, UART_ID3);
rev = serial_icr_read(up, UART_REV);
DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev);
if (id1 == 0x16 && id2 == 0xC9 &&
(id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) {
up->port.type = PORT_16C950;
/*
* Enable work around for the Oxford Semiconductor 952 rev B
* chip which causes it to seriously miscalculate baud rates
* when DLL is 0.
*/
if (id3 == 0x52 && rev == 0x01)
up->bugs |= UART_BUG_QUOT;
return;
}
/*
* We check for a XR16C850 by setting DLL and DLM to 0, and then
* reading back DLL and DLM. The chip type depends on the DLM
* value read back:
* 0x10 - XR16C850 and the DLL contains the chip revision.
* 0x12 - XR16C2850.
* 0x14 - XR16C854.
*/
id1 = autoconfig_read_divisor_id(up);
DEBUG_AUTOCONF("850id=%04x ", id1);
id2 = id1 >> 8;
if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) {
up->port.type = PORT_16850;
return;
}
/*
* It wasn't an XR16C850.
*
* We distinguish between the '654 and the '650 by counting
* how many bytes are in the FIFO. I'm using this for now,
* since that's the technique that was sent to me in the
* serial driver update, but I'm not convinced this works.
* I've had problems doing this in the past. -TYT
*/
if (size_fifo(up) == 64)
up->port.type = PORT_16654;
else
up->port.type = PORT_16650V2;
}
/*
* We detected a chip without a FIFO. Only two fall into
* this category - the original 8250 and the 16450. The
* 16450 has a scratch register (accessible with LCR=0)
*/
static void autoconfig_8250(struct uart_8250_port *up)
{
unsigned char scratch, status1, status2;
up->port.type = PORT_8250;
scratch = serial_in(up, UART_SCR);
serial_out(up, UART_SCR, 0xa5);
status1 = serial_in(up, UART_SCR);
serial_out(up, UART_SCR, 0x5a);
status2 = serial_in(up, UART_SCR);
serial_out(up, UART_SCR, scratch);
if (status1 == 0xa5 && status2 == 0x5a)
up->port.type = PORT_16450;
}
static int broken_efr(struct uart_8250_port *up)
{
/*
* Exar ST16C2550 "A2" devices incorrectly detect as
* having an EFR, and report an ID of 0x0201. See
* http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html
*/
if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16)
return 1;
return 0;
}
/*
* We know that the chip has FIFOs. Does it have an EFR? The
* EFR is located in the same register position as the IIR and
* we know the top two bits of the IIR are currently set. The
* EFR should contain zero. Try to read the EFR.
*/
static void autoconfig_16550a(struct uart_8250_port *up)
{
unsigned char status1, status2;
unsigned int iersave;
up->port.type = PORT_16550A;
up->capabilities |= UART_CAP_FIFO;
if (!IS_ENABLED(CONFIG_SERIAL_8250_16550A_VARIANTS))
return;
/*
* Check for presence of the EFR when DLAB is set.
* Only ST16C650V1 UARTs pass this test.
*/
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
if (serial_in(up, UART_EFR) == 0) {
serial_out(up, UART_EFR, 0xA8);
if (serial_in(up, UART_EFR) != 0) {
DEBUG_AUTOCONF("EFRv1 ");
up->port.type = PORT_16650;
up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
} else {
serial_out(up, UART_LCR, 0);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR7_64BYTE);
status1 = serial_in(up, UART_IIR) >> 5;
serial_out(up, UART_FCR, 0);
serial_out(up, UART_LCR, 0);
if (status1 == 7)
up->port.type = PORT_16550A_FSL64;
else
DEBUG_AUTOCONF("Motorola 8xxx DUART ");
}
serial_out(up, UART_EFR, 0);
return;
}
/*
* Maybe it requires 0xbf to be written to the LCR.
* (other ST16C650V2 UARTs, TI16C752A, etc)
*/
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) {
DEBUG_AUTOCONF("EFRv2 ");
autoconfig_has_efr(up);
return;
}
/*
* Check for a National Semiconductor SuperIO chip.
* Attempt to switch to bank 2, read the value of the LOOP bit
* from EXCR1. Switch back to bank 0, change it in MCR. Then
* switch back to bank 2, read it from EXCR1 again and check
* it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2
*/
serial_out(up, UART_LCR, 0);
status1 = serial8250_in_MCR(up);
serial_out(up, UART_LCR, 0xE0);
status2 = serial_in(up, 0x02); /* EXCR1 */
if (!((status2 ^ status1) & UART_MCR_LOOP)) {
serial_out(up, UART_LCR, 0);
serial8250_out_MCR(up, status1 ^ UART_MCR_LOOP);
serial_out(up, UART_LCR, 0xE0);
status2 = serial_in(up, 0x02); /* EXCR1 */
serial_out(up, UART_LCR, 0);
serial8250_out_MCR(up, status1);
if ((status2 ^ status1) & UART_MCR_LOOP) {
unsigned short quot;
serial_out(up, UART_LCR, 0xE0);
quot = serial_dl_read(up);
quot <<= 3;
if (ns16550a_goto_highspeed(up))
serial_dl_write(up, quot);
serial_out(up, UART_LCR, 0);
up->port.uartclk = 921600*16;
up->port.type = PORT_NS16550A;
up->capabilities |= UART_NATSEMI;
return;
}
}
/*
* No EFR. Try to detect a TI16750, which only sets bit 5 of
* the IIR when 64 byte FIFO mode is enabled when DLAB is set.
* Try setting it with and without DLAB set. Cheap clones
* set bit 5 without DLAB set.
*/
serial_out(up, UART_LCR, 0);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
status1 = serial_in(up, UART_IIR) >> 5;
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
status2 = serial_in(up, UART_IIR) >> 5;
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_out(up, UART_LCR, 0);
DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2);
if (status1 == 6 && status2 == 7) {
up->port.type = PORT_16750;
up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP;
return;
}
/*
* Try writing and reading the UART_IER_UUE bit (b6).
* If it works, this is probably one of the Xscale platform's
* internal UARTs.
* We're going to explicitly set the UUE bit to 0 before
* trying to write and read a 1 just to make sure it's not
* already a 1 and maybe locked there before we even start start.
*/
iersave = serial_in(up, UART_IER);
serial_out(up, UART_IER, iersave & ~UART_IER_UUE);
if (!(serial_in(up, UART_IER) & UART_IER_UUE)) {
/*
* OK it's in a known zero state, try writing and reading
* without disturbing the current state of the other bits.
*/
serial_out(up, UART_IER, iersave | UART_IER_UUE);
if (serial_in(up, UART_IER) & UART_IER_UUE) {
/*
* It's an Xscale.
* We'll leave the UART_IER_UUE bit set to 1 (enabled).
*/
DEBUG_AUTOCONF("Xscale ");
up->port.type = PORT_XSCALE;
up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE;
return;
}
} else {
/*
* If we got here we couldn't force the IER_UUE bit to 0.
* Log it and continue.
*/
DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 ");
}
serial_out(up, UART_IER, iersave);
/*
* We distinguish between 16550A and U6 16550A by counting
* how many bytes are in the FIFO.
*/
if (up->port.type == PORT_16550A && size_fifo(up) == 64) {
up->port.type = PORT_U6_16550A;
up->capabilities |= UART_CAP_AFE;
}
}
/*
* This routine is called by rs_init() to initialize a specific serial
* port. It determines what type of UART chip this serial port is
* using: 8250, 16450, 16550, 16550A. The important question is
* whether or not this UART is a 16550A or not, since this will
* determine whether or not we can use its FIFO features or not.
*/
static void autoconfig(struct uart_8250_port *up)
{
unsigned char status1, scratch, scratch2, scratch3;
unsigned char save_lcr, save_mcr;
struct uart_port *port = &up->port;
unsigned long flags;
unsigned int old_capabilities;
if (!port->iobase && !port->mapbase && !port->membase)
return;
DEBUG_AUTOCONF("%s: autoconf (0x%04lx, 0x%p): ",
port->name, port->iobase, port->membase);
/*
* We really do need global IRQs disabled here - we're going to
* be frobbing the chips IRQ enable register to see if it exists.
*/
spin_lock_irqsave(&port->lock, flags);
up->capabilities = 0;
up->bugs = 0;
if (!(port->flags & UPF_BUGGY_UART)) {
/*
* Do a simple existence test first; if we fail this,
* there's no point trying anything else.
*
* 0x80 is used as a nonsense port to prevent against
* false positives due to ISA bus float. The
* assumption is that 0x80 is a non-existent port;
* which should be safe since include/asm/io.h also
* makes this assumption.
*
* Note: this is safe as long as MCR bit 4 is clear
* and the device is in "PC" mode.
*/
scratch = serial_in(up, UART_IER);
serial_out(up, UART_IER, 0);
#ifdef __i386__
outb(0xff, 0x080);
#endif
/*
* Mask out IER[7:4] bits for test as some UARTs (e.g. TL
* 16C754B) allow only to modify them if an EFR bit is set.
*/
scratch2 = serial_in(up, UART_IER) & 0x0f;
serial_out(up, UART_IER, 0x0F);
#ifdef __i386__
outb(0, 0x080);
#endif
scratch3 = serial_in(up, UART_IER) & 0x0f;
serial_out(up, UART_IER, scratch);
if (scratch2 != 0 || scratch3 != 0x0F) {
/*
* We failed; there's nothing here
*/
spin_unlock_irqrestore(&port->lock, flags);
DEBUG_AUTOCONF("IER test failed (%02x, %02x) ",
scratch2, scratch3);
goto out;
}
}
save_mcr = serial8250_in_MCR(up);
save_lcr = serial_in(up, UART_LCR);
/*
* Check to see if a UART is really there. Certain broken
* internal modems based on the Rockwell chipset fail this
* test, because they apparently don't implement the loopback
* test mode. So this test is skipped on the COM 1 through
* COM 4 ports. This *should* be safe, since no board
* manufacturer would be stupid enough to design a board
* that conflicts with COM 1-4 --- we hope!
*/
if (!(port->flags & UPF_SKIP_TEST)) {
serial8250_out_MCR(up, UART_MCR_LOOP | 0x0A);
status1 = serial_in(up, UART_MSR) & 0xF0;
serial8250_out_MCR(up, save_mcr);
if (status1 != 0x90) {
spin_unlock_irqrestore(&port->lock, flags);
DEBUG_AUTOCONF("LOOP test failed (%02x) ",
status1);
goto out;
}
}
/*
* We're pretty sure there's a port here. Lets find out what
* type of port it is. The IIR top two bits allows us to find
* out if it's 8250 or 16450, 16550, 16550A or later. This
* determines what we test for next.
*
* We also initialise the EFR (if any) to zero for later. The
* EFR occupies the same register location as the FCR and IIR.
*/
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_EFR, 0);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
scratch = serial_in(up, UART_IIR) >> 6;
switch (scratch) {
case 0:
autoconfig_8250(up);
break;
case 1:
port->type = PORT_UNKNOWN;
break;
case 2:
port->type = PORT_16550;
break;
case 3:
autoconfig_16550a(up);
break;
}
#ifdef CONFIG_SERIAL_8250_RSA
/*
* Only probe for RSA ports if we got the region.
*/
if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA &&
__enable_rsa(up))
port->type = PORT_RSA;
#endif
serial_out(up, UART_LCR, save_lcr);
port->fifosize = uart_config[up->port.type].fifo_size;
old_capabilities = up->capabilities;
up->capabilities = uart_config[port->type].flags;
up->tx_loadsz = uart_config[port->type].tx_loadsz;
if (port->type == PORT_UNKNOWN)
goto out_lock;
/*
* Reset the UART.
*/
#ifdef CONFIG_SERIAL_8250_RSA
if (port->type == PORT_RSA)
serial_out(up, UART_RSA_FRR, 0);
#endif
serial8250_out_MCR(up, save_mcr);
serial8250_clear_fifos(up);
serial_in(up, UART_RX);
if (up->capabilities & UART_CAP_UUE)
serial_out(up, UART_IER, UART_IER_UUE);
else
serial_out(up, UART_IER, 0);
out_lock:
spin_unlock_irqrestore(&port->lock, flags);
/*
* Check if the device is a Fintek F81216A
*/
if (port->type == PORT_16550A && port->iotype == UPIO_PORT)
fintek_8250_probe(up);
if (up->capabilities != old_capabilities) {
dev_warn(port->dev, "detected caps %08x should be %08x\n",
old_capabilities, up->capabilities);
}
out:
DEBUG_AUTOCONF("iir=%d ", scratch);
DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name);
}
static void autoconfig_irq(struct uart_8250_port *up)
{
struct uart_port *port = &up->port;
unsigned char save_mcr, save_ier;
unsigned char save_ICP = 0;
unsigned int ICP = 0;
unsigned long irqs;
int irq;
if (port->flags & UPF_FOURPORT) {
ICP = (port->iobase & 0xfe0) | 0x1f;
save_ICP = inb_p(ICP);
outb_p(0x80, ICP);
inb_p(ICP);
}
if (uart_console(port))
console_lock();
/* forget possible initially masked and pending IRQ */
probe_irq_off(probe_irq_on());
save_mcr = serial8250_in_MCR(up);
save_ier = serial_in(up, UART_IER);
serial8250_out_MCR(up, UART_MCR_OUT1 | UART_MCR_OUT2);
irqs = probe_irq_on();
serial8250_out_MCR(up, 0);
udelay(10);
if (port->flags & UPF_FOURPORT) {
serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
} else {
serial8250_out_MCR(up,
UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
}
serial_out(up, UART_IER, 0x0f); /* enable all intrs */
serial_in(up, UART_LSR);
serial_in(up, UART_RX);
serial_in(up, UART_IIR);
serial_in(up, UART_MSR);
serial_out(up, UART_TX, 0xFF);
udelay(20);
irq = probe_irq_off(irqs);
serial8250_out_MCR(up, save_mcr);
serial_out(up, UART_IER, save_ier);
if (port->flags & UPF_FOURPORT)
outb_p(save_ICP, ICP);
if (uart_console(port))
console_unlock();
port->irq = (irq > 0) ? irq : 0;
}
static void serial8250_stop_rx(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
serial8250_rpm_get(up);
up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
up->port.read_status_mask &= ~UART_LSR_DR;
serial_port_out(port, UART_IER, up->ier);
serial8250_rpm_put(up);
}
/**
* serial8250_em485_stop_tx() - generic ->rs485_stop_tx() callback
* @p: uart 8250 port
*
* Generic callback usable by 8250 uart drivers to stop rs485 transmission.
*/
void serial8250_em485_stop_tx(struct uart_8250_port *p)
{
unsigned char mcr = serial8250_in_MCR(p);
if (p->port.rs485.flags & SER_RS485_RTS_AFTER_SEND)
mcr |= UART_MCR_RTS;
else
mcr &= ~UART_MCR_RTS;
serial8250_out_MCR(p, mcr);
/*
* Empty the RX FIFO, we are not interested in anything
* received during the half-duplex transmission.
* Enable previously disabled RX interrupts.
*/
if (!(p->port.rs485.flags & SER_RS485_RX_DURING_TX)) {
serial8250_clear_and_reinit_fifos(p);
p->ier |= UART_IER_RLSI | UART_IER_RDI;
serial_port_out(&p->port, UART_IER, p->ier);
}
}
EXPORT_SYMBOL_GPL(serial8250_em485_stop_tx);
static enum hrtimer_restart serial8250_em485_handle_stop_tx(struct hrtimer *t)
{
struct uart_8250_em485 *em485 = container_of(t, struct uart_8250_em485,
stop_tx_timer);
struct uart_8250_port *p = em485->port;
unsigned long flags;
serial8250_rpm_get(p);
spin_lock_irqsave(&p->port.lock, flags);
if (em485->active_timer == &em485->stop_tx_timer) {
p->rs485_stop_tx(p);
em485->active_timer = NULL;
em485->tx_stopped = true;
}
spin_unlock_irqrestore(&p->port.lock, flags);
serial8250_rpm_put(p);
return HRTIMER_NORESTART;
}
static void start_hrtimer_ms(struct hrtimer *hrt, unsigned long msec)
{
hrtimer_start(hrt, ms_to_ktime(msec), HRTIMER_MODE_REL);
}
static void __stop_tx_rs485(struct uart_8250_port *p)
{
struct uart_8250_em485 *em485 = p->em485;
/*
* rs485_stop_tx() is going to set RTS according to config
* AND flush RX FIFO if required.
*/
if (p->port.rs485.delay_rts_after_send > 0) {
em485->active_timer = &em485->stop_tx_timer;
start_hrtimer_ms(&em485->stop_tx_timer,
p->port.rs485.delay_rts_after_send);
} else {
p->rs485_stop_tx(p);
em485->active_timer = NULL;
em485->tx_stopped = true;
}
}
static inline void __do_stop_tx(struct uart_8250_port *p)
{
if (serial8250_clear_THRI(p))
serial8250_rpm_put_tx(p);
}
static inline void __stop_tx(struct uart_8250_port *p)
{
struct uart_8250_em485 *em485 = p->em485;
if (em485) {
unsigned char lsr = serial_in(p, UART_LSR);
/*
* To provide required timeing and allow FIFO transfer,
* __stop_tx_rs485() must be called only when both FIFO and
* shift register are empty. It is for device driver to enable
* interrupt on TEMT.
*/
if ((lsr & BOTH_EMPTY) != BOTH_EMPTY)
return;
__stop_tx_rs485(p);
}
__do_stop_tx(p);
}
static void serial8250_stop_tx(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
serial8250_rpm_get(up);
__stop_tx(up);
/*
* We really want to stop the transmitter from sending.
*/
if (port->type == PORT_16C950) {
up->acr |= UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
serial8250_rpm_put(up);
}
static inline void __start_tx(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
if (up->dma && !up->dma->tx_dma(up))
return;
if (serial8250_set_THRI(up)) {
if (up->bugs & UART_BUG_TXEN) {
unsigned char lsr;
lsr = serial_in(up, UART_LSR);
up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
if (lsr & UART_LSR_THRE)
serial8250_tx_chars(up);
}
}
/*
* Re-enable the transmitter if we disabled it.
*/
if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
up->acr &= ~UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
}
/**
* serial8250_em485_start_tx() - generic ->rs485_start_tx() callback
* @up: uart 8250 port
*
* Generic callback usable by 8250 uart drivers to start rs485 transmission.
* Assumes that setting the RTS bit in the MCR register means RTS is high.
* (Some chips use inverse semantics.) Further assumes that reception is
* stoppable by disabling the UART_IER_RDI interrupt. (Some chips set the
* UART_LSR_DR bit even when UART_IER_RDI is disabled, foiling this approach.)
*/
void serial8250_em485_start_tx(struct uart_8250_port *up)
{
unsigned char mcr = serial8250_in_MCR(up);
if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX))
serial8250_stop_rx(&up->port);
if (up->port.rs485.flags & SER_RS485_RTS_ON_SEND)
mcr |= UART_MCR_RTS;
else
mcr &= ~UART_MCR_RTS;
serial8250_out_MCR(up, mcr);
}
EXPORT_SYMBOL_GPL(serial8250_em485_start_tx);
static inline void start_tx_rs485(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
struct uart_8250_em485 *em485 = up->em485;
em485->active_timer = NULL;
if (em485->tx_stopped) {
em485->tx_stopped = false;
up->rs485_start_tx(up);
if (up->port.rs485.delay_rts_before_send > 0) {
em485->active_timer = &em485->start_tx_timer;
start_hrtimer_ms(&em485->start_tx_timer,
up->port.rs485.delay_rts_before_send);
return;
}
}
__start_tx(port);
}
static enum hrtimer_restart serial8250_em485_handle_start_tx(struct hrtimer *t)
{
struct uart_8250_em485 *em485 = container_of(t, struct uart_8250_em485,
start_tx_timer);
struct uart_8250_port *p = em485->port;
unsigned long flags;
spin_lock_irqsave(&p->port.lock, flags);
if (em485->active_timer == &em485->start_tx_timer) {
__start_tx(&p->port);
em485->active_timer = NULL;
}
spin_unlock_irqrestore(&p->port.lock, flags);
return HRTIMER_NORESTART;
}
static void serial8250_start_tx(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
struct uart_8250_em485 *em485 = up->em485;
serial8250_rpm_get_tx(up);
if (em485 &&
em485->active_timer == &em485->start_tx_timer)
return;
if (em485)
start_tx_rs485(port);
else
__start_tx(port);
}
static void serial8250_throttle(struct uart_port *port)
{
port->throttle(port);
}
static void serial8250_unthrottle(struct uart_port *port)
{
port->unthrottle(port);
}
static void serial8250_disable_ms(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
/* no MSR capabilities */
if (up->bugs & UART_BUG_NOMSR)
return;
mctrl_gpio_disable_ms(up->gpios);
up->ier &= ~UART_IER_MSI;
serial_port_out(port, UART_IER, up->ier);
}
static void serial8250_enable_ms(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
/* no MSR capabilities */
if (up->bugs & UART_BUG_NOMSR)
return;
mctrl_gpio_enable_ms(up->gpios);
up->ier |= UART_IER_MSI;
serial8250_rpm_get(up);
serial_port_out(port, UART_IER, up->ier);
serial8250_rpm_put(up);
}
void serial8250_read_char(struct uart_8250_port *up, unsigned char lsr)
{
struct uart_port *port = &up->port;
unsigned char ch;
char flag = TTY_NORMAL;
if (likely(lsr & UART_LSR_DR))
ch = serial_in(up, UART_RX);
else
/*
* Intel 82571 has a Serial Over Lan device that will
* set UART_LSR_BI without setting UART_LSR_DR when
* it receives a break. To avoid reading from the
* receive buffer without UART_LSR_DR bit set, we
* just force the read character to be 0
*/
ch = 0;
port->icount.rx++;
lsr |= up->lsr_saved_flags;
up->lsr_saved_flags = 0;
if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) {
if (lsr & UART_LSR_BI) {
lsr &= ~(UART_LSR_FE | UART_LSR_PE);
port->icount.brk++;
/*
* We do the SysRQ and SAK checking
* here because otherwise the break
* may get masked by ignore_status_mask
* or read_status_mask.
*/
if (uart_handle_break(port))
return;
} else if (lsr & UART_LSR_PE)
port->icount.parity++;
else if (lsr & UART_LSR_FE)
port->icount.frame++;
if (lsr & UART_LSR_OE)
port->icount.overrun++;
/*
* Mask off conditions which should be ignored.
*/
lsr &= port->read_status_mask;
if (lsr & UART_LSR_BI) {
dev_dbg(port->dev, "handling break\n");
flag = TTY_BREAK;
} else if (lsr & UART_LSR_PE)
flag = TTY_PARITY;
else if (lsr & UART_LSR_FE)
flag = TTY_FRAME;
}
if (uart_prepare_sysrq_char(port, ch))
return;
uart_insert_char(port, lsr, UART_LSR_OE, ch, flag);
}
EXPORT_SYMBOL_GPL(serial8250_read_char);
/*
* serial8250_rx_chars: processes according to the passed in LSR
* value, and returns the remaining LSR bits not handled
* by this Rx routine.
*/
unsigned char serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr)
{
struct uart_port *port = &up->port;
int max_count = 256;
do {
serial8250_read_char(up, lsr);
if (--max_count == 0)
break;
lsr = serial_in(up, UART_LSR);
} while (lsr & (UART_LSR_DR | UART_LSR_BI));
tty_flip_buffer_push(&port->state->port);
return lsr;
}
EXPORT_SYMBOL_GPL(serial8250_rx_chars);
void serial8250_tx_chars(struct uart_8250_port *up)
{
struct uart_port *port = &up->port;
struct circ_buf *xmit = &port->state->xmit;
int count;
if (port->x_char) {
serial_out(up, UART_TX, port->x_char);
port->icount.tx++;
port->x_char = 0;
return;
}
if (uart_tx_stopped(port)) {
serial8250_stop_tx(port);
return;
}
if (uart_circ_empty(xmit)) {
__stop_tx(up);
return;
}
count = up->tx_loadsz;
do {
serial_out(up, UART_TX, xmit->buf[xmit->tail]);
if (up->bugs & UART_BUG_TXRACE) {
/*
* The Aspeed BMC virtual UARTs have a bug where data
* may get stuck in the BMC's Tx FIFO from bursts of
* writes on the APB interface.
*
* Delay back-to-back writes by a read cycle to avoid
* stalling the VUART. Read a register that won't have
* side-effects and discard the result.
*/
serial_in(up, UART_SCR);
}
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
port->icount.tx++;
if (uart_circ_empty(xmit))
break;
if ((up->capabilities & UART_CAP_HFIFO) &&
(serial_in(up, UART_LSR) & BOTH_EMPTY) != BOTH_EMPTY)
break;
/* The BCM2835 MINI UART THRE bit is really a not-full bit. */
if ((up->capabilities & UART_CAP_MINI) &&
!(serial_in(up, UART_LSR) & UART_LSR_THRE))
break;
} while (--count > 0);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(port);
/*
* With RPM enabled, we have to wait until the FIFO is empty before the
* HW can go idle. So we get here once again with empty FIFO and disable
* the interrupt and RPM in __stop_tx()
*/
if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM))
__stop_tx(up);
}
EXPORT_SYMBOL_GPL(serial8250_tx_chars);
/* Caller holds uart port lock */
unsigned int serial8250_modem_status(struct uart_8250_port *up)
{
struct uart_port *port = &up->port;
unsigned int status = serial_in(up, UART_MSR);
status |= up->msr_saved_flags;
up->msr_saved_flags = 0;
if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
port->state != NULL) {
if (status & UART_MSR_TERI)
port->icount.rng++;
if (status & UART_MSR_DDSR)
port->icount.dsr++;
if (status & UART_MSR_DDCD)
uart_handle_dcd_change(port, status & UART_MSR_DCD);
if (status & UART_MSR_DCTS)
uart_handle_cts_change(port, status & UART_MSR_CTS);
wake_up_interruptible(&port->state->port.delta_msr_wait);
}
return status;
}
EXPORT_SYMBOL_GPL(serial8250_modem_status);
static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir)
{
switch (iir & 0x3f) {
case UART_IIR_RX_TIMEOUT:
serial8250_rx_dma_flush(up);
fallthrough;
case UART_IIR_RLSI:
return true;
}
return up->dma->rx_dma(up);
}
/*
* This handles the interrupt from one port.
*/
int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
{
unsigned char status;
struct uart_8250_port *up = up_to_u8250p(port);
bool skip_rx = false;
if (iir & UART_IIR_NO_INT)
return 0;
spin_lock(&port->lock);
status = serial_port_in(port, UART_LSR);
/*
* If port is stopped and there are no error conditions in the
* FIFO, then don't drain the FIFO, as this may lead to TTY buffer
* overflow. Not servicing, RX FIFO would trigger auto HW flow
* control when FIFO occupancy reaches preset threshold, thus
* halting RX. This only works when auto HW flow control is
* available.
*/
if (!(status & (UART_LSR_FIFOE | UART_LSR_BRK_ERROR_BITS)) &&
(port->status & (UPSTAT_AUTOCTS | UPSTAT_AUTORTS)) &&
!(port->read_status_mask & UART_LSR_DR))
skip_rx = true;
if (status & (UART_LSR_DR | UART_LSR_BI) && !skip_rx) {
if (!up->dma || handle_rx_dma(up, iir))
status = serial8250_rx_chars(up, status);
}
serial8250_modem_status(up);
if ((!up->dma || up->dma->tx_err) && (status & UART_LSR_THRE) &&
(up->ier & UART_IER_THRI))
serial8250_tx_chars(up);
uart_unlock_and_check_sysrq(port);
return 1;
}
EXPORT_SYMBOL_GPL(serial8250_handle_irq);
static int serial8250_default_handle_irq(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned int iir;
int ret;
serial8250_rpm_get(up);
iir = serial_port_in(port, UART_IIR);
ret = serial8250_handle_irq(port, iir);
serial8250_rpm_put(up);
return ret;
}
/*
* Newer 16550 compatible parts such as the SC16C650 & Altera 16550 Soft IP
* have a programmable TX threshold that triggers the THRE interrupt in
* the IIR register. In this case, the THRE interrupt indicates the FIFO
* has space available. Load it up with tx_loadsz bytes.
*/
static int serial8250_tx_threshold_handle_irq(struct uart_port *port)
{
unsigned long flags;
unsigned int iir = serial_port_in(port, UART_IIR);
/* TX Threshold IRQ triggered so load up FIFO */
if ((iir & UART_IIR_ID) == UART_IIR_THRI) {
struct uart_8250_port *up = up_to_u8250p(port);
spin_lock_irqsave(&port->lock, flags);
serial8250_tx_chars(up);
spin_unlock_irqrestore(&port->lock, flags);
}
iir = serial_port_in(port, UART_IIR);
return serial8250_handle_irq(port, iir);
}
static unsigned int serial8250_tx_empty(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned long flags;
unsigned int lsr;
serial8250_rpm_get(up);
spin_lock_irqsave(&port->lock, flags);
lsr = serial_port_in(port, UART_LSR);
up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
spin_unlock_irqrestore(&port->lock, flags);
serial8250_rpm_put(up);
return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
}
unsigned int serial8250_do_get_mctrl(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned int status;
unsigned int val;
serial8250_rpm_get(up);
status = serial8250_modem_status(up);
serial8250_rpm_put(up);
val = serial8250_MSR_to_TIOCM(status);
if (up->gpios)
return mctrl_gpio_get(up->gpios, &val);
return val;
}
EXPORT_SYMBOL_GPL(serial8250_do_get_mctrl);
static unsigned int serial8250_get_mctrl(struct uart_port *port)
{
if (port->get_mctrl)
return port->get_mctrl(port);
return serial8250_do_get_mctrl(port);
}
void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned char mcr;
if (port->rs485.flags & SER_RS485_ENABLED) {
if (serial8250_in_MCR(up) & UART_MCR_RTS)
mctrl |= TIOCM_RTS;
else
mctrl &= ~TIOCM_RTS;
}
mcr = serial8250_TIOCM_to_MCR(mctrl);
mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;
serial8250_out_MCR(up, mcr);
}
EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl);
static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
if (port->set_mctrl)
port->set_mctrl(port, mctrl);
else
serial8250_do_set_mctrl(port, mctrl);
}
static void serial8250_break_ctl(struct uart_port *port, int break_state)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned long flags;
serial8250_rpm_get(up);
spin_lock_irqsave(&port->lock, flags);
if (break_state == -1)
up->lcr |= UART_LCR_SBC;
else
up->lcr &= ~UART_LCR_SBC;
serial_port_out(port, UART_LCR, up->lcr);
spin_unlock_irqrestore(&port->lock, flags);
serial8250_rpm_put(up);
}
/*
* Wait for transmitter & holding register to empty
*/
static void wait_for_xmitr(struct uart_8250_port *up, int bits)
{
unsigned int status, tmout = 10000;
/* Wait up to 10ms for the character(s) to be sent. */
for (;;) {
status = serial_in(up, UART_LSR);
up->lsr_saved_flags |= status & LSR_SAVE_FLAGS;
if ((status & bits) == bits)
break;
if (--tmout == 0)
break;
udelay(1);
touch_nmi_watchdog();
}
/* Wait up to 1s for flow control if necessary */
if (up->port.flags & UPF_CONS_FLOW) {
for (tmout = 1000000; tmout; tmout--) {
unsigned int msr = serial_in(up, UART_MSR);
up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
if (msr & UART_MSR_CTS)
break;
udelay(1);
touch_nmi_watchdog();
}
}
}
#ifdef CONFIG_CONSOLE_POLL
/*
* Console polling routines for writing and reading from the uart while
* in an interrupt or debug context.
*/
static int serial8250_get_poll_char(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned char lsr;
int status;
serial8250_rpm_get(up);
lsr = serial_port_in(port, UART_LSR);
if (!(lsr & UART_LSR_DR)) {
status = NO_POLL_CHAR;
goto out;
}
status = serial_port_in(port, UART_RX);
out:
serial8250_rpm_put(up);
return status;
}
static void serial8250_put_poll_char(struct uart_port *port,
unsigned char c)
{
unsigned int ier;
struct uart_8250_port *up = up_to_u8250p(port);
serial8250_rpm_get(up);
/*
* First save the IER then disable the interrupts
*/
ier = serial_port_in(port, UART_IER);
if (up->capabilities & UART_CAP_UUE)
serial_port_out(port, UART_IER, UART_IER_UUE);
else
serial_port_out(port, UART_IER, 0);
wait_for_xmitr(up, BOTH_EMPTY);
/*
* Send the character out.
*/
serial_port_out(port, UART_TX, c);
/*
* Finally, wait for transmitter to become empty
* and restore the IER
*/
wait_for_xmitr(up, BOTH_EMPTY);
serial_port_out(port, UART_IER, ier);
serial8250_rpm_put(up);
}
#endif /* CONFIG_CONSOLE_POLL */
int serial8250_do_startup(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned long flags;
unsigned char lsr, iir;
int retval;
if (!port->fifosize)
port->fifosize = uart_config[port->type].fifo_size;
if (!up->tx_loadsz)
up->tx_loadsz = uart_config[port->type].tx_loadsz;
if (!up->capabilities)
up->capabilities = uart_config[port->type].flags;
up->mcr = 0;
if (port->iotype != up->cur_iotype)
set_io_from_upio(port);
serial8250_rpm_get(up);
if (port->type == PORT_16C950) {
/* Wake up and initialize UART */
up->acr = 0;
serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
serial_port_out(port, UART_EFR, UART_EFR_ECB);
serial_port_out(port, UART_IER, 0);
serial_port_out(port, UART_LCR, 0);
serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
serial_port_out(port, UART_EFR, UART_EFR_ECB);
serial_port_out(port, UART_LCR, 0);
}
if (port->type == PORT_DA830) {
/* Reset the port */
serial_port_out(port, UART_IER, 0);
serial_port_out(port, UART_DA830_PWREMU_MGMT, 0);
mdelay(10);
/* Enable Tx, Rx and free run mode */
serial_port_out(port, UART_DA830_PWREMU_MGMT,
UART_DA830_PWREMU_MGMT_UTRST |
UART_DA830_PWREMU_MGMT_URRST |
UART_DA830_PWREMU_MGMT_FREE);
}
if (port->type == PORT_NPCM) {
/*
* Nuvoton calls the scratch register 'UART_TOR' (timeout
* register). Enable it, and set TIOC (timeout interrupt
* comparator) to be 0x20 for correct operation.
*/
serial_port_out(port, UART_NPCM_TOR, UART_NPCM_TOIE | 0x20);
}
#ifdef CONFIG_SERIAL_8250_RSA
/*
* If this is an RSA port, see if we can kick it up to the
* higher speed clock.
*/
enable_rsa(up);
#endif
/*
* Clear the FIFO buffers and disable them.
* (they will be reenabled in set_termios())
*/
serial8250_clear_fifos(up);
/*
* Clear the interrupt registers.
*/
serial_port_in(port, UART_LSR);
serial_port_in(port, UART_RX);
serial_port_in(port, UART_IIR);
serial_port_in(port, UART_MSR);
/*
* At this point, there's no way the LSR could still be 0xff;
* if it is, then bail out, because there's likely no UART
* here.
*/
if (!(port->flags & UPF_BUGGY_UART) &&
(serial_port_in(port, UART_LSR) == 0xff)) {
dev_info_ratelimited(port->dev, "LSR safety check engaged!\n");
retval = -ENODEV;
goto out;
}
/*
* For a XR16C850, we need to set the trigger levels
*/
if (port->type == PORT_16850) {
unsigned char fctr;
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX);
serial_port_out(port, UART_FCTR,
fctr | UART_FCTR_TRGD | UART_FCTR_RX);
serial_port_out(port, UART_TRG, UART_TRG_96);
serial_port_out(port, UART_FCTR,
fctr | UART_FCTR_TRGD | UART_FCTR_TX);
serial_port_out(port, UART_TRG, UART_TRG_96);
serial_port_out(port, UART_LCR, 0);
}
/*
* For the Altera 16550 variants, set TX threshold trigger level.
*/
if (((port->type == PORT_ALTR_16550_F32) ||
(port->type == PORT_ALTR_16550_F64) ||
(port->type == PORT_ALTR_16550_F128)) && (port->fifosize > 1)) {
/* Bounds checking of TX threshold (valid 0 to fifosize-2) */
if ((up->tx_loadsz < 2) || (up->tx_loadsz > port->fifosize)) {
dev_err(port->dev, "TX FIFO Threshold errors, skipping\n");
} else {
serial_port_out(port, UART_ALTR_AFR,
UART_ALTR_EN_TXFIFO_LW);
serial_port_out(port, UART_ALTR_TX_LOW,
port->fifosize - up->tx_loadsz);
port->handle_irq = serial8250_tx_threshold_handle_irq;
}
}
/* Check if we need to have shared IRQs */
if (port->irq && (up->port.flags & UPF_SHARE_IRQ))
up->port.irqflags |= IRQF_SHARED;
if (port->irq && !(up->port.flags & UPF_NO_THRE_TEST)) {
unsigned char iir1;
if (port->irqflags & IRQF_SHARED)
disable_irq_nosync(port->irq);
/*
* Test for UARTs that do not reassert THRE when the
* transmitter is idle and the interrupt has already
* been cleared. Real 16550s should always reassert
* this interrupt whenever the transmitter is idle and
* the interrupt is enabled. Delays are necessary to
* allow register changes to become visible.
*/
spin_lock_irqsave(&port->lock, flags);
wait_for_xmitr(up, UART_LSR_THRE);
serial_port_out_sync(port, UART_IER, UART_IER_THRI);
udelay(1); /* allow THRE to set */
iir1 = serial_port_in(port, UART_IIR);
serial_port_out(port, UART_IER, 0);
serial_port_out_sync(port, UART_IER, UART_IER_THRI);
udelay(1); /* allow a working UART time to re-assert THRE */
iir = serial_port_in(port, UART_IIR);
serial_port_out(port, UART_IER, 0);
spin_unlock_irqrestore(&port->lock, flags);
if (port->irqflags & IRQF_SHARED)
enable_irq(port->irq);
/*
* If the interrupt is not reasserted, or we otherwise
* don't trust the iir, setup a timer to kick the UART
* on a regular basis.
*/
if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) ||
up->port.flags & UPF_BUG_THRE) {
up->bugs |= UART_BUG_THRE;
}
}
retval = up->ops->setup_irq(up);
if (retval)
goto out;
/*
* Now, initialize the UART
*/
serial_port_out(port, UART_LCR, UART_LCR_WLEN8);
spin_lock_irqsave(&port->lock, flags);
if (up->port.flags & UPF_FOURPORT) {
if (!up->port.irq)
up->port.mctrl |= TIOCM_OUT1;
} else
/*
* Most PC uarts need OUT2 raised to enable interrupts.
*/
if (port->irq)
up->port.mctrl |= TIOCM_OUT2;
serial8250_set_mctrl(port, port->mctrl);
/*
* Serial over Lan (SoL) hack:
* Intel 8257x Gigabit ethernet chips have a 16550 emulation, to be
* used for Serial Over Lan. Those chips take a longer time than a
* normal serial device to signalize that a transmission data was
* queued. Due to that, the above test generally fails. One solution
* would be to delay the reading of iir. However, this is not
* reliable, since the timeout is variable. So, let's just don't
* test if we receive TX irq. This way, we'll never enable
* UART_BUG_TXEN.
*/
if (up->port.quirks & UPQ_NO_TXEN_TEST)
goto dont_test_tx_en;
/*
* Do a quick test to see if we receive an interrupt when we enable
* the TX irq.
*/
serial_port_out(port, UART_IER, UART_IER_THRI);
lsr = serial_port_in(port, UART_LSR);
iir = serial_port_in(port, UART_IIR);
serial_port_out(port, UART_IER, 0);
if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) {
if (!(up->bugs & UART_BUG_TXEN)) {
up->bugs |= UART_BUG_TXEN;
dev_dbg(port->dev, "enabling bad tx status workarounds\n");
}
} else {
up->bugs &= ~UART_BUG_TXEN;
}
dont_test_tx_en:
spin_unlock_irqrestore(&port->lock, flags);
/*
* Clear the interrupt registers again for luck, and clear the
* saved flags to avoid getting false values from polling
* routines or the previous session.
*/
serial_port_in(port, UART_LSR);
serial_port_in(port, UART_RX);
serial_port_in(port, UART_IIR);
serial_port_in(port, UART_MSR);
up->lsr_saved_flags = 0;
up->msr_saved_flags = 0;
/*
* Request DMA channels for both RX and TX.
*/
if (up->dma) {
const char *msg = NULL;
if (uart_console(port))
msg = "forbid DMA for kernel console";
else if (serial8250_request_dma(up))
msg = "failed to request DMA";
if (msg) {
dev_warn_ratelimited(port->dev, "%s\n", msg);
up->dma = NULL;
}
}
/*
* Set the IER shadow for rx interrupts but defer actual interrupt
* enable until after the FIFOs are enabled; otherwise, an already-
* active sender can swamp the interrupt handler with "too much work".
*/
up->ier = UART_IER_RLSI | UART_IER_RDI;
if (port->flags & UPF_FOURPORT) {
unsigned int icp;
/*
* Enable interrupts on the AST Fourport board
*/
icp = (port->iobase & 0xfe0) | 0x01f;
outb_p(0x80, icp);
inb_p(icp);
}
retval = 0;
out:
serial8250_rpm_put(up);
return retval;
}
EXPORT_SYMBOL_GPL(serial8250_do_startup);
static int serial8250_startup(struct uart_port *port)
{
if (port->startup)
return port->startup(port);
return serial8250_do_startup(port);
}
void serial8250_do_shutdown(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned long flags;
serial8250_rpm_get(up);
/*
* Disable interrupts from this port
*/
spin_lock_irqsave(&port->lock, flags);
up->ier = 0;
serial_port_out(port, UART_IER, 0);
spin_unlock_irqrestore(&port->lock, flags);
synchronize_irq(port->irq);
if (up->dma)
serial8250_release_dma(up);
spin_lock_irqsave(&port->lock, flags);
if (port->flags & UPF_FOURPORT) {
/* reset interrupts on the AST Fourport board */
inb((port->iobase & 0xfe0) | 0x1f);
port->mctrl |= TIOCM_OUT1;
} else
port->mctrl &= ~TIOCM_OUT2;
serial8250_set_mctrl(port, port->mctrl);
spin_unlock_irqrestore(&port->lock, flags);
/*
* Disable break condition and FIFOs
*/
serial_port_out(port, UART_LCR,
serial_port_in(port, UART_LCR) & ~UART_LCR_SBC);
serial8250_clear_fifos(up);
#ifdef CONFIG_SERIAL_8250_RSA
/*
* Reset the RSA board back to 115kbps compat mode.
*/
disable_rsa(up);
#endif
/*
* Read data port to reset things, and then unlink from
* the IRQ chain.
*/
serial_port_in(port, UART_RX);
serial8250_rpm_put(up);
up->ops->release_irq(up);
}
EXPORT_SYMBOL_GPL(serial8250_do_shutdown);
static void serial8250_shutdown(struct uart_port *port)
{
if (port->shutdown)
port->shutdown(port);
else
serial8250_do_shutdown(port);
}
/* Nuvoton NPCM UARTs have a custom divisor calculation */
static unsigned int npcm_get_divisor(struct uart_8250_port *up,
unsigned int baud)
{
struct uart_port *port = &up->port;
return DIV_ROUND_CLOSEST(port->uartclk, 16 * baud + 2) - 2;
}
static unsigned int serial8250_do_get_divisor(struct uart_port *port,
unsigned int baud,
unsigned int *frac)
{
upf_t magic_multiplier = port->flags & UPF_MAGIC_MULTIPLIER;
struct uart_8250_port *up = up_to_u8250p(port);
unsigned int quot;
/*
* Handle magic divisors for baud rates above baud_base on SMSC
* Super I/O chips. We clamp custom rates from clk/6 and clk/12
* up to clk/4 (0x8001) and clk/8 (0x8002) respectively. These
* magic divisors actually reprogram the baud rate generator's
* reference clock derived from chips's 14.318MHz clock input.
*
* Documentation claims that with these magic divisors the base
* frequencies of 7.3728MHz and 3.6864MHz are used respectively
* for the extra baud rates of 460800bps and 230400bps rather
* than the usual base frequency of 1.8462MHz. However empirical
* evidence contradicts that.
*
* Instead bit 7 of the DLM register (bit 15 of the divisor) is
* effectively used as a clock prescaler selection bit for the
* base frequency of 7.3728MHz, always used. If set to 0, then
* the base frequency is divided by 4 for use by the Baud Rate
* Generator, for the usual arrangement where the value of 1 of
* the divisor produces the baud rate of 115200bps. Conversely,
* if set to 1 and high-speed operation has been enabled with the
* Serial Port Mode Register in the Device Configuration Space,
* then the base frequency is supplied directly to the Baud Rate
* Generator, so for the divisor values of 0x8001, 0x8002, 0x8003,
* 0x8004, etc. the respective baud rates produced are 460800bps,
* 230400bps, 153600bps, 115200bps, etc.
*
* In all cases only low 15 bits of the divisor are used to divide
* the baud base and therefore 32767 is the maximum divisor value
* possible, even though documentation says that the programmable
* Baud Rate Generator is capable of dividing the internal PLL
* clock by any divisor from 1 to 65535.
*/
if (magic_multiplier && baud >= port->uartclk / 6)
quot = 0x8001;
else if (magic_multiplier && baud >= port->uartclk / 12)
quot = 0x8002;
else if (up->port.type == PORT_NPCM)
quot = npcm_get_divisor(up, baud);
else
quot = uart_get_divisor(port, baud);
/*
* Oxford Semi 952 rev B workaround
*/
if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0)
quot++;
return quot;
}
static unsigned int serial8250_get_divisor(struct uart_port *port,
unsigned int baud,
unsigned int *frac)
{
if (port->get_divisor)
return port->get_divisor(port, baud, frac);
return serial8250_do_get_divisor(port, baud, frac);
}
static unsigned char serial8250_compute_lcr(struct uart_8250_port *up,
tcflag_t c_cflag)
{
unsigned char cval;
switch (c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (c_cflag & PARENB) {
cval |= UART_LCR_PARITY;
if (up->bugs & UART_BUG_PARITY)
up->fifo_bug = true;
}
if (!(c_cflag & PARODD))
cval |= UART_LCR_EPAR;
#ifdef CMSPAR
if (c_cflag & CMSPAR)
cval |= UART_LCR_SPAR;
#endif
return cval;
}
void serial8250_do_set_divisor(struct uart_port *port, unsigned int baud,
unsigned int quot, unsigned int quot_frac)
{
struct uart_8250_port *up = up_to_u8250p(port);
/* Workaround to enable 115200 baud on OMAP1510 internal ports */
if (is_omap1510_8250(up)) {
if (baud == 115200) {
quot = 1;
serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1);
} else
serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0);
}
/*
* For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2,
* otherwise just set DLAB
*/
if (up->capabilities & UART_NATSEMI)
serial_port_out(port, UART_LCR, 0xe0);
else
serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
serial_dl_write(up, quot);
}
EXPORT_SYMBOL_GPL(serial8250_do_set_divisor);
static void serial8250_set_divisor(struct uart_port *port, unsigned int baud,
unsigned int quot, unsigned int quot_frac)
{
if (port->set_divisor)
port->set_divisor(port, baud, quot, quot_frac);
else
serial8250_do_set_divisor(port, baud, quot, quot_frac);
}
static unsigned int serial8250_get_baud_rate(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
unsigned int tolerance = port->uartclk / 100;
unsigned int min;
unsigned int max;
/*
* Handle magic divisors for baud rates above baud_base on SMSC
* Super I/O chips. Enable custom rates of clk/4 and clk/8, but
* disable divisor values beyond 32767, which are unavailable.
*/
if (port->flags & UPF_MAGIC_MULTIPLIER) {
min = port->uartclk / 16 / UART_DIV_MAX >> 1;
max = (port->uartclk + tolerance) / 4;
} else {
min = port->uartclk / 16 / UART_DIV_MAX;
max = (port->uartclk + tolerance) / 16;
}
/*
* Ask the core to calculate the divisor for us.
* Allow 1% tolerance at the upper limit so uart clks marginally
* slower than nominal still match standard baud rates without
* causing transmission errors.
*/
return uart_get_baud_rate(port, termios, old, min, max);
}
/*
* Note in order to avoid the tty port mutex deadlock don't use the next method
* within the uart port callbacks. Primarily it's supposed to be utilized to
* handle a sudden reference clock rate change.
*/
void serial8250_update_uartclk(struct uart_port *port, unsigned int uartclk)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned int baud, quot, frac = 0;
struct ktermios *termios;
unsigned long flags;
mutex_lock(&port->state->port.mutex);
if (port->uartclk == uartclk)
goto out_lock;
port->uartclk = uartclk;
if (!tty_port_initialized(&port->state->port))
goto out_lock;
termios = &port->state->port.tty->termios;
baud = serial8250_get_baud_rate(port, termios, NULL);
quot = serial8250_get_divisor(port, baud, &frac);
serial8250_rpm_get(up);
spin_lock_irqsave(&port->lock, flags);
uart_update_timeout(port, termios->c_cflag, baud);
serial8250_set_divisor(port, baud, quot, frac);
serial_port_out(port, UART_LCR, up->lcr);
spin_unlock_irqrestore(&port->lock, flags);
serial8250_rpm_put(up);
out_lock:
mutex_unlock(&port->state->port.mutex);
}
EXPORT_SYMBOL_GPL(serial8250_update_uartclk);
void
serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned char cval;
unsigned long flags;
unsigned int baud, quot, frac = 0;
if (up->capabilities & UART_CAP_MINI) {
termios->c_cflag &= ~(CSTOPB | PARENB | PARODD | CMSPAR);
if ((termios->c_cflag & CSIZE) == CS5 ||
(termios->c_cflag & CSIZE) == CS6)
termios->c_cflag = (termios->c_cflag & ~CSIZE) | CS7;
}
cval = serial8250_compute_lcr(up, termios->c_cflag);
baud = serial8250_get_baud_rate(port, termios, old);
quot = serial8250_get_divisor(port, baud, &frac);
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
serial8250_rpm_get(up);
spin_lock_irqsave(&port->lock, flags);
up->lcr = cval; /* Save computed LCR */
if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) {
/* NOTE: If fifo_bug is not set, a user can set RX_trigger. */
if ((baud < 2400 && !up->dma) || up->fifo_bug) {
up->fcr &= ~UART_FCR_TRIGGER_MASK;
up->fcr |= UART_FCR_TRIGGER_1;
}
}
/*
* MCR-based auto flow control. When AFE is enabled, RTS will be
* deasserted when the receive FIFO contains more characters than
* the trigger, or the MCR RTS bit is cleared.
*/
if (up->capabilities & UART_CAP_AFE) {
up->mcr &= ~UART_MCR_AFE;
if (termios->c_cflag & CRTSCTS)
up->mcr |= UART_MCR_AFE;
}
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
port->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
port->read_status_mask |= UART_LSR_BI;
/*
* Characteres to ignore
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= UART_LSR_DR;
/*
* CTS flow control flag and modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
if (!(up->bugs & UART_BUG_NOMSR) &&
UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
if (up->capabilities & UART_CAP_UUE)
up->ier |= UART_IER_UUE;
if (up->capabilities & UART_CAP_RTOIE)
up->ier |= UART_IER_RTOIE;
serial_port_out(port, UART_IER, up->ier);
if (up->capabilities & UART_CAP_EFR) {
unsigned char efr = 0;
/*
* TI16C752/Startech hardware flow control. FIXME:
* - TI16C752 requires control thresholds to be set.
* - UART_MCR_RTS is ineffective if auto-RTS mode is enabled.
*/
if (termios->c_cflag & CRTSCTS)
efr |= UART_EFR_CTS;
serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
if (port->flags & UPF_EXAR_EFR)
serial_port_out(port, UART_XR_EFR, efr);
else
serial_port_out(port, UART_EFR, efr);
}
serial8250_set_divisor(port, baud, quot, frac);
/*
* LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
* is written without DLAB set, this mode will be disabled.
*/
if (port->type == PORT_16750)
serial_port_out(port, UART_FCR, up->fcr);
serial_port_out(port, UART_LCR, up->lcr); /* reset DLAB */
if (port->type != PORT_16750) {
/* emulated UARTs (Lucent Venus 167x) need two steps */
if (up->fcr & UART_FCR_ENABLE_FIFO)
serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_port_out(port, UART_FCR, up->fcr); /* set fcr */
}
serial8250_set_mctrl(port, port->mctrl);
spin_unlock_irqrestore(&port->lock, flags);
serial8250_rpm_put(up);
/* Don't rewrite B0 */
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
}
EXPORT_SYMBOL(serial8250_do_set_termios);
static void
serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
if (port->set_termios)
port->set_termios(port, termios, old);
else
serial8250_do_set_termios(port, termios, old);
}
void serial8250_do_set_ldisc(struct uart_port *port, struct ktermios *termios)
{
if (termios->c_line == N_PPS) {
port->flags |= UPF_HARDPPS_CD;
spin_lock_irq(&port->lock);
serial8250_enable_ms(port);
spin_unlock_irq(&port->lock);
} else {
port->flags &= ~UPF_HARDPPS_CD;
if (!UART_ENABLE_MS(port, termios->c_cflag)) {
spin_lock_irq(&port->lock);
serial8250_disable_ms(port);
spin_unlock_irq(&port->lock);
}
}
}
EXPORT_SYMBOL_GPL(serial8250_do_set_ldisc);
static void
serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios)
{
if (port->set_ldisc)
port->set_ldisc(port, termios);
else
serial8250_do_set_ldisc(port, termios);
}
void serial8250_do_pm(struct uart_port *port, unsigned int state,
unsigned int oldstate)
{
struct uart_8250_port *p = up_to_u8250p(port);
serial8250_set_sleep(p, state != 0);
}
EXPORT_SYMBOL(serial8250_do_pm);
static void
serial8250_pm(struct uart_port *port, unsigned int state,
unsigned int oldstate)
{
if (port->pm)
port->pm(port, state, oldstate);
else
serial8250_do_pm(port, state, oldstate);
}
static unsigned int serial8250_port_size(struct uart_8250_port *pt)
{
if (pt->port.mapsize)
return pt->port.mapsize;
if (pt->port.iotype == UPIO_AU) {
if (pt->port.type == PORT_RT2880)
return 0x100;
return 0x1000;
}
if (is_omap1_8250(pt))
return 0x16 << pt->port.regshift;
return 8 << pt->port.regshift;
}
/*
* Resource handling.
*/
static int serial8250_request_std_resource(struct uart_8250_port *up)
{
unsigned int size = serial8250_port_size(up);
struct uart_port *port = &up->port;
int ret = 0;
switch (port->iotype) {
case UPIO_AU:
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM32BE:
case UPIO_MEM16:
case UPIO_MEM:
if (!port->mapbase)
break;
if (!request_mem_region(port->mapbase, size, "serial")) {
ret = -EBUSY;
break;
}
if (port->flags & UPF_IOREMAP) {
port->membase = ioremap(port->mapbase, size);
if (!port->membase) {
release_mem_region(port->mapbase, size);
ret = -ENOMEM;
}
}
break;
case UPIO_HUB6:
case UPIO_PORT:
if (!request_region(port->iobase, size, "serial"))
ret = -EBUSY;
break;
}
return ret;
}
static void serial8250_release_std_resource(struct uart_8250_port *up)
{
unsigned int size = serial8250_port_size(up);
struct uart_port *port = &up->port;
switch (port->iotype) {
case UPIO_AU:
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM32BE:
case UPIO_MEM16:
case UPIO_MEM:
if (!port->mapbase)
break;
if (port->flags & UPF_IOREMAP) {
iounmap(port->membase);
port->membase = NULL;
}
release_mem_region(port->mapbase, size);
break;
case UPIO_HUB6:
case UPIO_PORT:
release_region(port->iobase, size);
break;
}
}
static void serial8250_release_port(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
serial8250_release_std_resource(up);
}
static int serial8250_request_port(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
return serial8250_request_std_resource(up);
}
static int fcr_get_rxtrig_bytes(struct uart_8250_port *up)
{
const struct serial8250_config *conf_type = &uart_config[up->port.type];
unsigned char bytes;
bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)];
return bytes ? bytes : -EOPNOTSUPP;
}
static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes)
{
const struct serial8250_config *conf_type = &uart_config[up->port.type];
int i;
if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)])
return -EOPNOTSUPP;
for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) {
if (bytes < conf_type->rxtrig_bytes[i])
/* Use the nearest lower value */
return (--i) << UART_FCR_R_TRIG_SHIFT;
}
return UART_FCR_R_TRIG_11;
}
static int do_get_rxtrig(struct tty_port *port)
{
struct uart_state *state = container_of(port, struct uart_state, port);
struct uart_port *uport = state->uart_port;
struct uart_8250_port *up = up_to_u8250p(uport);
if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1)
return -EINVAL;
return fcr_get_rxtrig_bytes(up);
}
static int do_serial8250_get_rxtrig(struct tty_port *port)
{
int rxtrig_bytes;
mutex_lock(&port->mutex);
rxtrig_bytes = do_get_rxtrig(port);
mutex_unlock(&port->mutex);
return rxtrig_bytes;
}
static ssize_t rx_trig_bytes_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct tty_port *port = dev_get_drvdata(dev);
int rxtrig_bytes;
rxtrig_bytes = do_serial8250_get_rxtrig(port);
if (rxtrig_bytes < 0)
return rxtrig_bytes;
return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes);
}
static int do_set_rxtrig(struct tty_port *port, unsigned char bytes)
{
struct uart_state *state = container_of(port, struct uart_state, port);
struct uart_port *uport = state->uart_port;
struct uart_8250_port *up = up_to_u8250p(uport);
int rxtrig;
if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 ||
up->fifo_bug)
return -EINVAL;
rxtrig = bytes_to_fcr_rxtrig(up, bytes);
if (rxtrig < 0)
return rxtrig;
serial8250_clear_fifos(up);
up->fcr &= ~UART_FCR_TRIGGER_MASK;
up->fcr |= (unsigned char)rxtrig;
serial_out(up, UART_FCR, up->fcr);
return 0;
}
static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes)
{
int ret;
mutex_lock(&port->mutex);
ret = do_set_rxtrig(port, bytes);
mutex_unlock(&port->mutex);
return ret;
}
static ssize_t rx_trig_bytes_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t count)
{
struct tty_port *port = dev_get_drvdata(dev);
unsigned char bytes;
int ret;
if (!count)
return -EINVAL;
ret = kstrtou8(buf, 10, &bytes);
if (ret < 0)
return ret;
ret = do_serial8250_set_rxtrig(port, bytes);
if (ret < 0)
return ret;
return count;
}
static DEVICE_ATTR_RW(rx_trig_bytes);
static struct attribute *serial8250_dev_attrs[] = {
&dev_attr_rx_trig_bytes.attr,
NULL
};
static struct attribute_group serial8250_dev_attr_group = {
.attrs = serial8250_dev_attrs,
};
static void register_dev_spec_attr_grp(struct uart_8250_port *up)
{
const struct serial8250_config *conf_type = &uart_config[up->port.type];
if (conf_type->rxtrig_bytes[0])
up->port.attr_group = &serial8250_dev_attr_group;
}
static void serial8250_config_port(struct uart_port *port, int flags)
{
struct uart_8250_port *up = up_to_u8250p(port);
int ret;
/*
* Find the region that we can probe for. This in turn
* tells us whether we can probe for the type of port.
*/
ret = serial8250_request_std_resource(up);
if (ret < 0)
return;
if (port->iotype != up->cur_iotype)
set_io_from_upio(port);
if (flags & UART_CONFIG_TYPE)
autoconfig(up);
if (port->rs485.flags & SER_RS485_ENABLED)
port->rs485_config(port, &port->rs485);
/* if access method is AU, it is a 16550 with a quirk */
if (port->type == PORT_16550A && port->iotype == UPIO_AU)
up->bugs |= UART_BUG_NOMSR;
/* HW bugs may trigger IRQ while IIR == NO_INT */
if (port->type == PORT_TEGRA)
up->bugs |= UART_BUG_NOMSR;
if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
autoconfig_irq(up);
if (port->type == PORT_UNKNOWN)
serial8250_release_std_resource(up);
register_dev_spec_attr_grp(up);
up->fcr = uart_config[up->port.type].fcr;
}
static int
serial8250_verify_port(struct uart_port *port, struct serial_struct *ser)
{
if (ser->irq >= nr_irqs || ser->irq < 0 ||
ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS ||
ser->type == PORT_STARTECH)
return -EINVAL;
return 0;
}
static const char *serial8250_type(struct uart_port *port)
{
int type = port->type;
if (type >= ARRAY_SIZE(uart_config))
type = 0;
return uart_config[type].name;
}
static const struct uart_ops serial8250_pops = {
.tx_empty = serial8250_tx_empty,
.set_mctrl = serial8250_set_mctrl,
.get_mctrl = serial8250_get_mctrl,
.stop_tx = serial8250_stop_tx,
.start_tx = serial8250_start_tx,
.throttle = serial8250_throttle,
.unthrottle = serial8250_unthrottle,
.stop_rx = serial8250_stop_rx,
.enable_ms = serial8250_enable_ms,
.break_ctl = serial8250_break_ctl,
.startup = serial8250_startup,
.shutdown = serial8250_shutdown,
.set_termios = serial8250_set_termios,
.set_ldisc = serial8250_set_ldisc,
.pm = serial8250_pm,
.type = serial8250_type,
.release_port = serial8250_release_port,
.request_port = serial8250_request_port,
.config_port = serial8250_config_port,
.verify_port = serial8250_verify_port,
#ifdef CONFIG_CONSOLE_POLL
.poll_get_char = serial8250_get_poll_char,
.poll_put_char = serial8250_put_poll_char,
#endif
};
void serial8250_init_port(struct uart_8250_port *up)
{
struct uart_port *port = &up->port;
spin_lock_init(&port->lock);
port->ops = &serial8250_pops;
port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_8250_CONSOLE);
up->cur_iotype = 0xFF;
}
EXPORT_SYMBOL_GPL(serial8250_init_port);
void serial8250_set_defaults(struct uart_8250_port *up)
{
struct uart_port *port = &up->port;
if (up->port.flags & UPF_FIXED_TYPE) {
unsigned int type = up->port.type;
if (!up->port.fifosize)
up->port.fifosize = uart_config[type].fifo_size;
if (!up->tx_loadsz)
up->tx_loadsz = uart_config[type].tx_loadsz;
if (!up->capabilities)
up->capabilities = uart_config[type].flags;
}
set_io_from_upio(port);
/* default dma handlers */
if (up->dma) {
if (!up->dma->tx_dma)
up->dma->tx_dma = serial8250_tx_dma;
if (!up->dma->rx_dma)
up->dma->rx_dma = serial8250_rx_dma;
}
}
EXPORT_SYMBOL_GPL(serial8250_set_defaults);
#ifdef CONFIG_SERIAL_8250_CONSOLE
static void serial8250_console_putchar(struct uart_port *port, int ch)
{
struct uart_8250_port *up = up_to_u8250p(port);
wait_for_xmitr(up, UART_LSR_THRE);
serial_port_out(port, UART_TX, ch);
}
/*
* Restore serial console when h/w power-off detected
*/
static void serial8250_console_restore(struct uart_8250_port *up)
{
struct uart_port *port = &up->port;
struct ktermios termios;
unsigned int baud, quot, frac = 0;
termios.c_cflag = port->cons->cflag;
if (port->state->port.tty && termios.c_cflag == 0)
termios.c_cflag = port->state->port.tty->termios.c_cflag;
baud = serial8250_get_baud_rate(port, &termios, NULL);
quot = serial8250_get_divisor(port, baud, &frac);
serial8250_set_divisor(port, baud, quot, frac);
serial_port_out(port, UART_LCR, up->lcr);
serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
}
/*
* Print a string to the serial port trying not to disturb
* any possible real use of the port...
*
* The console_lock must be held when we get here.
*
* Doing runtime PM is really a bad idea for the kernel console.
* Thus, we assume the function is called when device is powered up.
*/
void serial8250_console_write(struct uart_8250_port *up, const char *s,
unsigned int count)
{
struct uart_8250_em485 *em485 = up->em485;
struct uart_port *port = &up->port;
unsigned long flags;
unsigned int ier;
int locked = 1;
touch_nmi_watchdog();
if (oops_in_progress)
locked = spin_trylock_irqsave(&port->lock, flags);
else
spin_lock_irqsave(&port->lock, flags);
/*
* First save the IER then disable the interrupts
*/
ier = serial_port_in(port, UART_IER);
if (up->capabilities & UART_CAP_UUE)
serial_port_out(port, UART_IER, UART_IER_UUE);
else
serial_port_out(port, UART_IER, 0);
/* check scratch reg to see if port powered off during system sleep */
if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) {
serial8250_console_restore(up);
up->canary = 0;
}
if (em485) {
if (em485->tx_stopped)
up->rs485_start_tx(up);
mdelay(port->rs485.delay_rts_before_send);
}
uart_console_write(port, s, count, serial8250_console_putchar);
/*
* Finally, wait for transmitter to become empty
* and restore the IER
*/
wait_for_xmitr(up, BOTH_EMPTY);
if (em485) {
mdelay(port->rs485.delay_rts_after_send);
if (em485->tx_stopped)
up->rs485_stop_tx(up);
}
serial_port_out(port, UART_IER, ier);
/*
* The receive handling will happen properly because the
* receive ready bit will still be set; it is not cleared
* on read. However, modem control will not, we must
* call it if we have saved something in the saved flags
* while processing with interrupts off.
*/
if (up->msr_saved_flags)
serial8250_modem_status(up);
if (locked)
spin_unlock_irqrestore(&port->lock, flags);
}
static unsigned int probe_baud(struct uart_port *port)
{
unsigned char lcr, dll, dlm;
unsigned int quot;
lcr = serial_port_in(port, UART_LCR);
serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB);
dll = serial_port_in(port, UART_DLL);
dlm = serial_port_in(port, UART_DLM);
serial_port_out(port, UART_LCR, lcr);
quot = (dlm << 8) | dll;
return (port->uartclk / 16) / quot;
}
int serial8250_console_setup(struct uart_port *port, char *options, bool probe)
{
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
int ret;
if (!port->iobase && !port->membase)
return -ENODEV;
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else if (probe)
baud = probe_baud(port);
ret = uart_set_options(port, port->cons, baud, parity, bits, flow);
if (ret)
return ret;
if (port->dev)
pm_runtime_get_sync(port->dev);
return 0;
}
int serial8250_console_exit(struct uart_port *port)
{
if (port->dev)
pm_runtime_put_sync(port->dev);
return 0;
}
#endif /* CONFIG_SERIAL_8250_CONSOLE */
MODULE_LICENSE("GPL");
Reference in New Issue View Git Blame Copy Permalink