mirror of
https://github.com/torvalds/linux.git
synced 2024-12-28 22:02:28 +00:00
d15891ca1f
STi series SOCs have a glue layer on top of the synopsis gmac IP, this glue layer needs to be configured before the gmac driver starts using the IP. This patch adds a support to this glue layer which is configured via stmmac setup, init, exit callbacks. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
59 lines
2.0 KiB
Plaintext
59 lines
2.0 KiB
Plaintext
STMicroelectronics SoC DWMAC glue layer controller
|
|
|
|
The device node has following properties.
|
|
|
|
Required properties:
|
|
- compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac" or
|
|
"st,stid127-dwmac".
|
|
- reg : Offset of the glue configuration register map in system
|
|
configuration regmap pointed by st,syscon property and size.
|
|
|
|
- reg-names : Should be "sti-ethconf".
|
|
|
|
- st,syscon : Should be phandle to system configuration node which
|
|
encompases this glue registers.
|
|
|
|
- st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
|
|
wired up in from different sources. One via TXCLK pin and other via CLK_125
|
|
pin. This wiring is totally board dependent. However the retiming glue
|
|
logic should be configured accordingly. Possible values for this property
|
|
|
|
"txclk" - if 125Mhz clock is wired up via txclk line.
|
|
"clk_125" - if 125Mhz clock is wired up via clk_125 line.
|
|
|
|
This property is only valid for Giga bit setup( GMII, RGMII), and it is
|
|
un-used for non-giga bit (MII and RMII) setups. Also note that internal
|
|
clockgen can not generate stable 125Mhz clock.
|
|
|
|
- st,ext-phyclk: This boolean property indicates who is generating the clock
|
|
for tx and rx. This property is only valid for RMII case where the clock can
|
|
be generated from the MAC or PHY.
|
|
|
|
- clock-names: should be "sti-ethclk".
|
|
- clocks: Should point to ethernet clockgen which can generate phyclk.
|
|
|
|
|
|
Example:
|
|
|
|
ethernet0: dwmac@fe810000 {
|
|
device_type = "network";
|
|
compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
|
|
reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
|
|
reg-names = "stmmaceth", "sti-ethconf";
|
|
interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
|
|
interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
|
|
phy-mode = "mii";
|
|
|
|
st,syscon = <&syscfg_rear>;
|
|
|
|
snps,pbl = <32>;
|
|
snps,mixed-burst;
|
|
|
|
resets = <&softreset STIH416_ETH0_SOFTRESET>;
|
|
reset-names = "stmmaceth";
|
|
pinctrl-0 = <&pinctrl_mii0>;
|
|
pinctrl-names = "default";
|
|
clocks = <&CLK_S_GMAC0_PHY>;
|
|
clock-names = "stmmaceth";
|
|
};
|