mirror of
https://github.com/torvalds/linux.git
synced 2024-12-06 02:52:22 +00:00
16be18d71c
LP-11 and LP-111 are CSI-2 bus states, not modes. Fix this. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
135 lines
4.5 KiB
ReStructuredText
135 lines
4.5 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0
|
|
|
|
.. _transmitter-receiver:
|
|
|
|
Pixel data transmitter and receiver drivers
|
|
===========================================
|
|
|
|
V4L2 supports various devices that transmit and receive pixel data. Examples of
|
|
these devices include a camera sensor, a TV tuner and a parallel, a BT.656 or a
|
|
CSI-2 receiver in an SoC.
|
|
|
|
Bus types
|
|
---------
|
|
|
|
The following busses are the most common. This section discusses these two only.
|
|
|
|
MIPI CSI-2
|
|
^^^^^^^^^^
|
|
|
|
CSI-2 is a data bus intended for transferring images from cameras to
|
|
the host SoC. It is defined by the `MIPI alliance`_.
|
|
|
|
.. _`MIPI alliance`: https://www.mipi.org/
|
|
|
|
Parallel and BT.656
|
|
^^^^^^^^^^^^^^^^^^^
|
|
|
|
The parallel and `BT.656`_ buses transport one bit of data on each clock cycle
|
|
per data line. The parallel bus uses synchronisation and other additional
|
|
signals whereas BT.656 embeds synchronisation.
|
|
|
|
.. _`BT.656`: https://en.wikipedia.org/wiki/ITU-R_BT.656
|
|
|
|
Transmitter drivers
|
|
-------------------
|
|
|
|
Transmitter drivers generally need to provide the receiver drivers with the
|
|
configuration of the transmitter. What is required depends on the type of the
|
|
bus. These are common for both busses.
|
|
|
|
Media bus pixel code
|
|
^^^^^^^^^^^^^^^^^^^^
|
|
|
|
See :ref:`v4l2-mbus-pixelcode`.
|
|
|
|
Link frequency
|
|
^^^^^^^^^^^^^^
|
|
|
|
The :ref:`V4L2_CID_LINK_FREQ <v4l2-cid-link-freq>` control is used to tell the
|
|
receiver the frequency of the bus (i.e. it is not the same as the symbol rate).
|
|
|
|
``.s_stream()`` callback
|
|
^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
The struct struct v4l2_subdev_video_ops->s_stream() callback is used by the
|
|
receiver driver to control the transmitter driver's streaming state.
|
|
|
|
|
|
CSI-2 transmitter drivers
|
|
-------------------------
|
|
|
|
Pixel rate
|
|
^^^^^^^^^^
|
|
|
|
The pixel rate on the bus is calculated as follows::
|
|
|
|
pixel_rate = link_freq * 2 * nr_of_lanes * 16 / k / bits_per_sample
|
|
|
|
where
|
|
|
|
.. list-table:: variables in pixel rate calculation
|
|
:header-rows: 1
|
|
|
|
* - variable or constant
|
|
- description
|
|
* - link_freq
|
|
- The value of the ``V4L2_CID_LINK_FREQ`` integer64 menu item.
|
|
* - nr_of_lanes
|
|
- Number of data lanes used on the CSI-2 link. This can
|
|
be obtained from the OF endpoint configuration.
|
|
* - 2
|
|
- Data is transferred on both rising and falling edge of the signal.
|
|
* - bits_per_sample
|
|
- Number of bits per sample.
|
|
* - k
|
|
- 16 for D-PHY and 7 for C-PHY
|
|
|
|
.. note::
|
|
|
|
The pixel rate calculated this way is **not** the same thing as the
|
|
pixel rate on the camera sensor's pixel array which is indicated by the
|
|
:ref:`V4L2_CID_PIXEL_RATE <v4l2-cid-pixel-rate>` control.
|
|
|
|
LP-11 and LP-111 states
|
|
^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
As part of transitioning to high speed mode, a CSI-2 transmitter typically
|
|
briefly sets the bus to LP-11 or LP-111 state, depending on the PHY. This period
|
|
may be as short as 100 µs, during which the receiver observes this state and
|
|
proceeds its own part of high speed mode transition.
|
|
|
|
Most receivers are capable of autonomously handling this once the software has
|
|
configured them to do so, but there are receivers which require software
|
|
involvement in observing LP-11 or LP-111 state. 100 µs is a brief period to hit
|
|
in software, especially when there is no interrupt telling something is
|
|
happening.
|
|
|
|
One way to address this is to configure the transmitter side explicitly to LP-11
|
|
or LP-111 state, which requires support from the transmitter hardware. This is
|
|
not universally available. Many devices return to this state once streaming is
|
|
stopped while the state after power-on is LP-00 or LP-000.
|
|
|
|
The ``.pre_streamon()`` callback may be used to prepare a transmitter for
|
|
transitioning to streaming state, but not yet start streaming. Similarly, the
|
|
``.post_streamoff()`` callback is used to undo what was done by the
|
|
``.pre_streamon()`` callback. The caller of ``.pre_streamon()`` is thus required
|
|
to call ``.post_streamoff()`` for each successful call of ``.pre_streamon()``.
|
|
|
|
In the context of CSI-2, the ``.pre_streamon()`` callback is used to transition
|
|
the transmitter to the LP-11 or LP-111 state. This also requires powering on the
|
|
device, so this should be only done when it is needed.
|
|
|
|
Receiver drivers that do not need explicit LP-11 or LP-111 state setup are
|
|
waived from calling the two callbacks.
|
|
|
|
Stopping the transmitter
|
|
^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
A transmitter stops sending the stream of images as a result of
|
|
calling the ``.s_stream()`` callback. Some transmitters may stop the
|
|
stream at a frame boundary whereas others stop immediately,
|
|
effectively leaving the current frame unfinished. The receiver driver
|
|
should not make assumptions either way, but function properly in both
|
|
cases.
|