Minki/linux
1
0
Fork 1
mirror of https://github.com/torvalds/linux.git synced 2024-11-15 00:21:59 +00:00
Code Issues Packages Projects Releases Wiki Activity
0eff0e2677
linux/drivers/mmc/host/mmci.h
Russell King c8ebae3703 ARM: mmci: add dmaengine-based DMA support 
Based on a patch from Linus Walleij.

Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface.  The changes over Linus' driver are:

- rename txsize_threshold to dmasize_threshold, as this reflects the
  purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer.  Some DMA controllers
  (eg, PL08x) are unable to be configured for scatter DMA and also listen
  to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
  They can do one or other but not both.  As MMCI uses LBREQ/LSREQ for the
  final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
  MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
  function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
  pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
  is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
  set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
  its own restrictions on buffer alignment, not the individual DMA engine
  users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
  causes LBREQ to be asserted for the last seven transfers, rather than
  six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
  transfer size required to complete the DMA operation.

Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04 13:25:49 +00:00

197 lines
5.5 KiB
C
Raw Blame History

/*
* linux/drivers/mmc/host/mmci.h - ARM PrimeCell MMCI PL180/1 driver
*
* Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#define MMCIPOWER 0x000
#define MCI_PWR_OFF 0x00
#define MCI_PWR_UP 0x02
#define MCI_PWR_ON 0x03
#define MCI_DATA2DIREN (1 << 2)
#define MCI_CMDDIREN (1 << 3)
#define MCI_DATA0DIREN (1 << 4)
#define MCI_DATA31DIREN (1 << 5)
#define MCI_OD (1 << 6)
#define MCI_ROD (1 << 7)
/* The ST Micro version does not have ROD */
#define MCI_FBCLKEN (1 << 7)
#define MCI_DATA74DIREN (1 << 8)
#define MMCICLOCK 0x004
#define MCI_CLK_ENABLE (1 << 8)
#define MCI_CLK_PWRSAVE (1 << 9)
#define MCI_CLK_BYPASS (1 << 10)
#define MCI_4BIT_BUS (1 << 11)
/* 8bit wide buses supported in ST Micro versions */
#define MCI_ST_8BIT_BUS (1 << 12)
#define MMCIARGUMENT 0x008
#define MMCICOMMAND 0x00c
#define MCI_CPSM_RESPONSE (1 << 6)
#define MCI_CPSM_LONGRSP (1 << 7)
#define MCI_CPSM_INTERRUPT (1 << 8)
#define MCI_CPSM_PENDING (1 << 9)
#define MCI_CPSM_ENABLE (1 << 10)
#define MCI_SDIO_SUSP (1 << 11)
#define MCI_ENCMD_COMPL (1 << 12)
#define MCI_NIEN (1 << 13)
#define MCI_CE_ATACMD (1 << 14)
#define MMCIRESPCMD 0x010
#define MMCIRESPONSE0 0x014
#define MMCIRESPONSE1 0x018
#define MMCIRESPONSE2 0x01c
#define MMCIRESPONSE3 0x020
#define MMCIDATATIMER 0x024
#define MMCIDATALENGTH 0x028
#define MMCIDATACTRL 0x02c
#define MCI_DPSM_ENABLE (1 << 0)
#define MCI_DPSM_DIRECTION (1 << 1)
#define MCI_DPSM_MODE (1 << 2)
#define MCI_DPSM_DMAENABLE (1 << 3)
#define MCI_DPSM_BLOCKSIZE (1 << 4)
/* Control register extensions in the ST Micro U300 and Ux500 versions */
#define MCI_ST_DPSM_RWSTART (1 << 8)
#define MCI_ST_DPSM_RWSTOP (1 << 9)
#define MCI_ST_DPSM_RWMOD (1 << 10)
#define MCI_ST_DPSM_SDIOEN (1 << 11)
/* Control register extensions in the ST Micro Ux500 versions */
#define MCI_ST_DPSM_DMAREQCTL (1 << 12)
#define MCI_ST_DPSM_DBOOTMODEEN (1 << 13)
#define MCI_ST_DPSM_BUSYMODE (1 << 14)
#define MCI_ST_DPSM_DDRMODE (1 << 15)
#define MMCIDATACNT 0x030
#define MMCISTATUS 0x034
#define MCI_CMDCRCFAIL (1 << 0)
#define MCI_DATACRCFAIL (1 << 1)
#define MCI_CMDTIMEOUT (1 << 2)
#define MCI_DATATIMEOUT (1 << 3)
#define MCI_TXUNDERRUN (1 << 4)
#define MCI_RXOVERRUN (1 << 5)
#define MCI_CMDRESPEND (1 << 6)
#define MCI_CMDSENT (1 << 7)
#define MCI_DATAEND (1 << 8)
#define MCI_DATABLOCKEND (1 << 10)
#define MCI_CMDACTIVE (1 << 11)
#define MCI_TXACTIVE (1 << 12)
#define MCI_RXACTIVE (1 << 13)
#define MCI_TXFIFOHALFEMPTY (1 << 14)
#define MCI_RXFIFOHALFFULL (1 << 15)
#define MCI_TXFIFOFULL (1 << 16)
#define MCI_RXFIFOFULL (1 << 17)
#define MCI_TXFIFOEMPTY (1 << 18)
#define MCI_RXFIFOEMPTY (1 << 19)
#define MCI_TXDATAAVLBL (1 << 20)
#define MCI_RXDATAAVLBL (1 << 21)
#define MCI_SDIOIT (1 << 22)
#define MCI_CEATAEND (1 << 23)
#define MMCICLEAR 0x038
#define MCI_CMDCRCFAILCLR (1 << 0)
#define MCI_DATACRCFAILCLR (1 << 1)
#define MCI_CMDTIMEOUTCLR (1 << 2)
#define MCI_DATATIMEOUTCLR (1 << 3)
#define MCI_TXUNDERRUNCLR (1 << 4)
#define MCI_RXOVERRUNCLR (1 << 5)
#define MCI_CMDRESPENDCLR (1 << 6)
#define MCI_CMDSENTCLR (1 << 7)
#define MCI_DATAENDCLR (1 << 8)
#define MCI_DATABLOCKENDCLR (1 << 10)
#define MCI_SDIOITC (1 << 22)
#define MCI_CEATAENDC (1 << 23)
#define MMCIMASK0 0x03c
#define MCI_CMDCRCFAILMASK (1 << 0)
#define MCI_DATACRCFAILMASK (1 << 1)
#define MCI_CMDTIMEOUTMASK (1 << 2)
#define MCI_DATATIMEOUTMASK (1 << 3)
#define MCI_TXUNDERRUNMASK (1 << 4)
#define MCI_RXOVERRUNMASK (1 << 5)
#define MCI_CMDRESPENDMASK (1 << 6)
#define MCI_CMDSENTMASK (1 << 7)
#define MCI_DATAENDMASK (1 << 8)
#define MCI_DATABLOCKENDMASK (1 << 10)
#define MCI_CMDACTIVEMASK (1 << 11)
#define MCI_TXACTIVEMASK (1 << 12)
#define MCI_RXACTIVEMASK (1 << 13)
#define MCI_TXFIFOHALFEMPTYMASK (1 << 14)
#define MCI_RXFIFOHALFFULLMASK (1 << 15)
#define MCI_TXFIFOFULLMASK (1 << 16)
#define MCI_RXFIFOFULLMASK (1 << 17)
#define MCI_TXFIFOEMPTYMASK (1 << 18)
#define MCI_RXFIFOEMPTYMASK (1 << 19)
#define MCI_TXDATAAVLBLMASK (1 << 20)
#define MCI_RXDATAAVLBLMASK (1 << 21)
#define MCI_SDIOITMASK (1 << 22)
#define MCI_CEATAENDMASK (1 << 23)
#define MMCIMASK1 0x040
#define MMCIFIFOCNT 0x048
#define MMCIFIFO 0x080 /* to 0x0bc */
#define MCI_IRQENABLE \
(MCI_CMDCRCFAILMASK|MCI_DATACRCFAILMASK|MCI_CMDTIMEOUTMASK| \
MCI_DATATIMEOUTMASK|MCI_TXUNDERRUNMASK|MCI_RXOVERRUNMASK| \
MCI_CMDRESPENDMASK|MCI_CMDSENTMASK)
/* These interrupts are directed to IRQ1 when two IRQ lines are available */
#define MCI_IRQ1MASK \
(MCI_RXFIFOHALFFULLMASK | MCI_RXDATAAVLBLMASK | \
MCI_TXFIFOHALFEMPTYMASK)
#define NR_SG 16
struct clk;
struct variant_data;
struct dma_chan;
struct mmci_host {
phys_addr_t phybase;
void __iomem *base;
struct mmc_request *mrq;
struct mmc_command *cmd;
struct mmc_data *data;
struct mmc_host *mmc;
struct clk *clk;
int gpio_cd;
int gpio_wp;
int gpio_cd_irq;
bool singleirq;
spinlock_t lock;
unsigned int mclk;
unsigned int cclk;
u32 pwr;
struct mmci_platform_data *plat;
struct variant_data *variant;
u8 hw_designer;
u8 hw_revision:4;
struct timer_list timer;
unsigned int oldstat;
/* pio stuff */
struct sg_mapping_iter sg_miter;
unsigned int size;
struct regulator *vcc;
#ifdef CONFIG_DMA_ENGINE
/* DMA stuff */
struct dma_chan *dma_current;
struct dma_chan *dma_rx_channel;
struct dma_chan *dma_tx_channel;
#define dma_inprogress(host) ((host)->dma_current)
#else
#define dma_inprogress(host) (0)
#endif
};
Reference in New Issue View Git Blame Copy Permalink