mirror of
https://github.com/torvalds/linux.git
synced 2024-11-27 14:41:39 +00:00
994d2cbb08
Add support for tag_sja1105 running on non-sja1105 DSA ports, by making sure that every time we dereference dp->priv, we check the switch's dsa_switch_ops (otherwise we access a struct sja1105_port structure that is in fact something else). This adds an unconditional build-time dependency between sja1105 being built as module => tag_sja1105 must also be built as module. This was there only for PTP before. Some sane defaults must also take place when not running on sja1105 hardware. These are: - sja1105_xmit_tpid: the sja1105 driver uses different VLAN protocols depending on VLAN awareness and switch revision (when an encapsulated VLAN must be sent). Default to 0x8100. - sja1105_rcv_meta_state_machine: this aggregates PTP frames with their metadata timestamp frames. When running on non-sja1105 hardware, don't do that and accept all frames unmodified. - sja1105_defer_xmit: calls sja1105_port_deferred_xmit in sja1105_main.c which writes a management route over SPI. When not running on sja1105 hardware, bypass the SPI write and send the frame as-is. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
162 lines
5.4 KiB
Plaintext
162 lines
5.4 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
menuconfig NET_DSA
|
|
tristate "Distributed Switch Architecture"
|
|
depends on BRIDGE || BRIDGE=n
|
|
depends on HSR || HSR=n
|
|
depends on INET && NETDEVICES
|
|
select GRO_CELLS
|
|
select NET_SWITCHDEV
|
|
select PHYLINK
|
|
select NET_DEVLINK
|
|
imply NET_SELFTESTS
|
|
help
|
|
Say Y if you want to enable support for the hardware switches supported
|
|
by the Distributed Switch Architecture.
|
|
|
|
if NET_DSA
|
|
|
|
# Drivers must select the appropriate tagging format(s)
|
|
|
|
config NET_DSA_TAG_AR9331
|
|
tristate "Tag driver for Atheros AR9331 SoC with built-in switch"
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames for
|
|
the Atheros AR9331 SoC with built-in switch.
|
|
|
|
config NET_DSA_TAG_BRCM_COMMON
|
|
tristate
|
|
default n
|
|
|
|
config NET_DSA_TAG_BRCM
|
|
tristate "Tag driver for Broadcom switches using in-frame headers"
|
|
select NET_DSA_TAG_BRCM_COMMON
|
|
help
|
|
Say Y if you want to enable support for tagging frames for the
|
|
Broadcom switches which place the tag after the MAC source address.
|
|
|
|
config NET_DSA_TAG_BRCM_LEGACY
|
|
tristate "Tag driver for Broadcom legacy switches using in-frame headers"
|
|
select NET_DSA_TAG_BRCM_COMMON
|
|
help
|
|
Say Y if you want to enable support for tagging frames for the
|
|
Broadcom legacy switches which place the tag after the MAC source
|
|
address.
|
|
|
|
config NET_DSA_TAG_BRCM_PREPEND
|
|
tristate "Tag driver for Broadcom switches using prepended headers"
|
|
select NET_DSA_TAG_BRCM_COMMON
|
|
help
|
|
Say Y if you want to enable support for tagging frames for the
|
|
Broadcom switches which places the tag before the Ethernet header
|
|
(prepended).
|
|
|
|
config NET_DSA_TAG_HELLCREEK
|
|
tristate "Tag driver for Hirschmann Hellcreek TSN switches"
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames
|
|
for the Hirschmann Hellcreek TSN switches.
|
|
|
|
config NET_DSA_TAG_GSWIP
|
|
tristate "Tag driver for Lantiq / Intel GSWIP switches"
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames for the
|
|
Lantiq / Intel GSWIP switches.
|
|
|
|
config NET_DSA_TAG_DSA_COMMON
|
|
tristate
|
|
|
|
config NET_DSA_TAG_DSA
|
|
tristate "Tag driver for Marvell switches using DSA headers"
|
|
select NET_DSA_TAG_DSA_COMMON
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames for the
|
|
Marvell switches which use DSA headers.
|
|
|
|
config NET_DSA_TAG_EDSA
|
|
tristate "Tag driver for Marvell switches using EtherType DSA headers"
|
|
select NET_DSA_TAG_DSA_COMMON
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames for the
|
|
Marvell switches which use EtherType DSA headers.
|
|
|
|
config NET_DSA_TAG_MTK
|
|
tristate "Tag driver for Mediatek switches"
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames for
|
|
Mediatek switches.
|
|
|
|
config NET_DSA_TAG_KSZ
|
|
tristate "Tag driver for Microchip 8795/9477/9893 families of switches"
|
|
help
|
|
Say Y if you want to enable support for tagging frames for the
|
|
Microchip 8795/9477/9893 families of switches.
|
|
|
|
config NET_DSA_TAG_RTL4_A
|
|
tristate "Tag driver for Realtek 4 byte protocol A tags"
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames for the
|
|
Realtek switches with 4 byte protocol A tags, sich as found in
|
|
the Realtek RTL8366RB.
|
|
|
|
config NET_DSA_TAG_OCELOT
|
|
tristate "Tag driver for Ocelot family of switches, using NPI port"
|
|
depends on MSCC_OCELOT_SWITCH_LIB || \
|
|
(MSCC_OCELOT_SWITCH_LIB=n && COMPILE_TEST)
|
|
select PACKING
|
|
help
|
|
Say Y or M if you want to enable NPI tagging for the Ocelot switches
|
|
(VSC7511, VSC7512, VSC7513, VSC7514, VSC9953, VSC9959). In this mode,
|
|
the frames over the Ethernet CPU port are prepended with a
|
|
hardware-defined injection/extraction frame header. Flow control
|
|
(PAUSE frames) over the CPU port is not supported when operating in
|
|
this mode.
|
|
|
|
config NET_DSA_TAG_OCELOT_8021Q
|
|
tristate "Tag driver for Ocelot family of switches, using VLAN"
|
|
depends on MSCC_OCELOT_SWITCH_LIB || \
|
|
(MSCC_OCELOT_SWITCH_LIB=n && COMPILE_TEST)
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames with a
|
|
custom VLAN-based header. Frames that require timestamping, such as
|
|
PTP, are not delivered over Ethernet but over register-based MMIO.
|
|
Flow control over the CPU port is functional in this mode. When using
|
|
this mode, less TCAM resources (VCAP IS1, IS2, ES0) are available for
|
|
use with tc-flower.
|
|
|
|
config NET_DSA_TAG_QCA
|
|
tristate "Tag driver for Qualcomm Atheros QCA8K switches"
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames for
|
|
the Qualcomm Atheros QCA8K switches.
|
|
|
|
config NET_DSA_TAG_LAN9303
|
|
tristate "Tag driver for SMSC/Microchip LAN9303 family of switches"
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames for the
|
|
SMSC/Microchip LAN9303 family of switches.
|
|
|
|
config NET_DSA_TAG_SJA1105
|
|
tristate "Tag driver for NXP SJA1105 switches"
|
|
depends on NET_DSA_SJA1105 || !NET_DSA_SJA1105
|
|
select PACKING
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames with the
|
|
NXP SJA1105 switch family. Both the native tagging protocol (which
|
|
is only for link-local traffic) as well as non-native tagging (based
|
|
on a custom 802.1Q VLAN header) are available.
|
|
|
|
config NET_DSA_TAG_TRAILER
|
|
tristate "Tag driver for switches using a trailer tag"
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames at
|
|
with a trailed. e.g. Marvell 88E6060.
|
|
|
|
config NET_DSA_TAG_XRS700X
|
|
tristate "Tag driver for XRS700x switches"
|
|
help
|
|
Say Y or M if you want to enable support for tagging frames for
|
|
Arrow SpeedChips XRS700x switches that use a single byte tag trailer.
|
|
|
|
endif
|