mirror of
https://github.com/torvalds/linux.git
synced 2024-12-25 20:32:22 +00:00
A mirror of the official Linux kernel repository just in case
063f7c8248
Pull "Renesas ARM Based SoC DT Updates for v4.15" from Simon Horman:
* r7s72100 (RZ/A1) Peach board
- Add pin groups for SCIF2 serial debug interface and Ethernet
This avoids relying on bootloader settings
- Support control of LED1 using gpio-leds
* r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
- Add MSIOF[012] support and define aliases for spi[0123]
* r8a7743 (RZ/G1M) SoC
- Add I2C and IIC core nodes
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven development platform
- Enable SDHI1 SD controller supporting high-speed and SDR50 transfers
- Add chosen node to allow correct selection of serial console
and the kernel command line
- Enable RTC support
- Enable USB2.0 host support
This includes enabling USB PHY and internal PCI
* r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22M-SM SoMs
- Enable Add SPI NOR support
This devices is used to boot up the system to the SoM DT
* r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
- Enable SDHI0 SD controller supporting high-speed transfers
* r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
- Add pnctl support for scif4
This avoids reling on boot loader settings
- Add EtherAVB support
* r8a7745 (RZ/G1E) iW-RainboW-G22M-SM SoM
- Add basic SoM support
- Enable MMCIF eMMC support
- Enable RTC support
- Enable SDHI1 SD controller supporting high-speed transfers
* r8a779[0-4] R-Car Gen2 SoCs
- Add reset control properties
Geert Uytterhoeven says:
This patch series describes the reset topology on all R-Car Gen2 Socs,
like was done before for R-Car Gen3 and RZ/G1.
Resets usually match the corresponding module clocks. Exceptions are:
- The audio module has resets for the Serial Sound Interfaces only,
- The display module has only a single reset for all DU channels, but
adding reset properties for the display is postponed upon request
from Laurent.
- Convert to new CPG/MSSR bindings
Geert Uytterhoven says:
Currently Renesas R-Car Gen2 SoCs use the common clk-rcar-gen2,
clk-mstp, and clk-div6 drivers, which depend on most clocks being
described in DT. Especially the module (MSTP) clocks are cumbersome
and error prone, due to 3 arrays (clocks, clock-indices, and
clock-output-names) to be kept in sync. In addition, the clk-mstp
driver cannot be extended easily to also support module resets, which
are provided by the same hardware module.
Hence when developing support for R-Car Gen3 SoCs, another approach
was chosen, which led to the CPG/MSSR driver core, and SoC-specific
subdrivers (initially for R-Car Gen3, but later also for RZ/G1).
This series converts the various R-Car Gen2 DTSes to migrate to the
new CPG/MSSR drivers that were added in v4.13-rc1.
* r8a779[0,1,3,4] R-Car Gen2 SoCs
- Stop grouping clocks under a "clocks" subnode
Geert Uytterhoeven says:
The current practice is to not group clocks under a "clocks" subnode,
but just put them together with the other on-SoC devices.
Hence this patch series implements this for the various R-Car Gen2
DTSes that still need this (r8a7792.dtsi is OK).
* r8a7794 (E2) Alt board
- Correct inverted sense of SD wip pins
* tag 'renesas-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (48 commits)
ARM: dts: r8a7743: Add MSIOF[012] support
ARM: dts: r8a7745: Add MSIOF[012] support
ARM: dts: iwg22d: Enable SDHI0 controller
ARM: dts: iwg22m: Add SPI NOR support
ARM: dts: r8a7745: Add QSPI support
ARM: dts: iwg20m: Add SPI NOR support
ARM: dts: r8a7743: Add QSPI support
ARM: dts: iwg22m: Enable SDHI1 controller
ARM: dts: r8a7745: Add SDHI controllers
ARM: dts: r8a7794: Add reset control properties
ARM: dts: r8a7793: Add reset control properties
ARM: dts: r8a7792: Add reset control properties
ARM: dts: r8a7791: Add reset control properties
ARM: dts: r8a7790: Add reset control properties
ARM: dts: r8a7743: Add IIC cores to dtsi
ARM: dts: alt: use correct logic for SD WP pins
ARM: dts: iwg20d-q7: Enable USB PHY
ARM: dts: iwg20d-q7: Enable internal PCI
ARM: dts: r8a7743: Link PCI USB devices to USB PHY
ARM: dts: r8a7743: Add USB PHY DT support
...
|
||
|---|---|---|
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| firmware | ||
| fs | ||
| include | ||
| init | ||
| ipc | ||
| kernel | ||
| lib | ||
| mm | ||
| net | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt | ||
| .cocciconfig | ||
| .get_maintainer.ignore | ||
| .gitattributes | ||
| .gitignore | ||
| .mailmap | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
Linux kernel ============ This file was moved to Documentation/admin-guide/README.rst Please notice that there are several guides for kernel developers and users. These guides can be rendered in a number of formats, like HTML and PDF. In order to build the documentation, use ``make htmldocs`` or ``make pdfdocs``. There are various text files in the Documentation/ subdirectory, several of them using the Restructured Text markup notation. See Documentation/00-INDEX for a list of what is contained in each file. Please read the Documentation/process/changes.rst file, as it contains the requirements for building and running the kernel, and information about the problems which may result by upgrading your kernel.