linux/drivers/gpu/drm/gma500/cdv_device.c
Alan Cox 055bf38d3d drm, gma500: Fix Cedarview boot failures in 3.3-rc
Production GMA3600/3650 hardware turns out to be subtly different to the
development platforms.  This combined with a minor driver bug is causing
the kernel to hang on these platforms.

This patch does the following

 - turn down a couple of messages that were meant to be debug and are
   causing much confusion

 - ensure the hotplug interrupt is disabled on Cedartrail systems.

 - fix a bug where gtt roll mode called psbfb_sync, which tries to sync
   the 2D engine. On other devices it is harmless as the 2D engine is
   present but not in use when in gtt roll mode, on Cedartrail it causes
   a hang

Without these changes 3.3-rc hangs on boot on Cedartrail based systems.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-03-05 14:53:01 -08:00

354 lines
8.8 KiB
C

/**************************************************************************
* Copyright (c) 2011, Intel Corporation.
* All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along with
* this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
*
**************************************************************************/
#include <linux/backlight.h>
#include <drm/drmP.h>
#include <drm/drm.h>
#include "gma_drm.h"
#include "psb_drv.h"
#include "psb_reg.h"
#include "psb_intel_reg.h"
#include "intel_bios.h"
#include "cdv_device.h"
#define VGA_SR_INDEX 0x3c4
#define VGA_SR_DATA 0x3c5
static void cdv_disable_vga(struct drm_device *dev)
{
u8 sr1;
u32 vga_reg;
vga_reg = VGACNTRL;
outb(1, VGA_SR_INDEX);
sr1 = inb(VGA_SR_DATA);
outb(sr1 | 1<<5, VGA_SR_DATA);
udelay(300);
REG_WRITE(vga_reg, VGA_DISP_DISABLE);
REG_READ(vga_reg);
}
static int cdv_output_init(struct drm_device *dev)
{
struct drm_psb_private *dev_priv = dev->dev_private;
cdv_disable_vga(dev);
cdv_intel_crt_init(dev, &dev_priv->mode_dev);
cdv_intel_lvds_init(dev, &dev_priv->mode_dev);
/* These bits indicate HDMI not SDVO on CDV, but we don't yet support
the HDMI interface */
if (REG_READ(SDVOB) & SDVO_DETECTED)
cdv_hdmi_init(dev, &dev_priv->mode_dev, SDVOB);
if (REG_READ(SDVOC) & SDVO_DETECTED)
cdv_hdmi_init(dev, &dev_priv->mode_dev, SDVOC);
return 0;
}
#ifdef CONFIG_BACKLIGHT_CLASS_DEVICE
/*
* Poulsbo Backlight Interfaces
*/
#define BLC_PWM_PRECISION_FACTOR 100 /* 10000000 */
#define BLC_PWM_FREQ_CALC_CONSTANT 32
#define MHz 1000000
#define PSB_BLC_PWM_PRECISION_FACTOR 10
#define PSB_BLC_MAX_PWM_REG_FREQ 0xFFFE
#define PSB_BLC_MIN_PWM_REG_FREQ 0x2
#define PSB_BACKLIGHT_PWM_POLARITY_BIT_CLEAR (0xFFFE)
#define PSB_BACKLIGHT_PWM_CTL_SHIFT (16)
static int cdv_brightness;
static struct backlight_device *cdv_backlight_device;
static int cdv_get_brightness(struct backlight_device *bd)
{
/* return locally cached var instead of HW read (due to DPST etc.) */
/* FIXME: ideally return actual value in case firmware fiddled with
it */
return cdv_brightness;
}
static int cdv_backlight_setup(struct drm_device *dev)
{
struct drm_psb_private *dev_priv = dev->dev_private;
unsigned long core_clock;
/* u32 bl_max_freq; */
/* unsigned long value; */
u16 bl_max_freq;
uint32_t value;
uint32_t blc_pwm_precision_factor;
/* get bl_max_freq and pol from dev_priv*/
if (!dev_priv->lvds_bl) {
dev_err(dev->dev, "Has no valid LVDS backlight info\n");
return -ENOENT;
}
bl_max_freq = dev_priv->lvds_bl->freq;
blc_pwm_precision_factor = PSB_BLC_PWM_PRECISION_FACTOR;
core_clock = dev_priv->core_freq;
value = (core_clock * MHz) / BLC_PWM_FREQ_CALC_CONSTANT;
value *= blc_pwm_precision_factor;
value /= bl_max_freq;
value /= blc_pwm_precision_factor;
if (value > (unsigned long long)PSB_BLC_MAX_PWM_REG_FREQ ||
value < (unsigned long long)PSB_BLC_MIN_PWM_REG_FREQ)
return -ERANGE;
else {
/* FIXME */
}
return 0;
}
static int cdv_set_brightness(struct backlight_device *bd)
{
int level = bd->props.brightness;
/* Percentage 1-100% being valid */
if (level < 1)
level = 1;
/*cdv_intel_lvds_set_brightness(dev, level); FIXME */
cdv_brightness = level;
return 0;
}
static const struct backlight_ops cdv_ops = {
.get_brightness = cdv_get_brightness,
.update_status = cdv_set_brightness,
};
static int cdv_backlight_init(struct drm_device *dev)
{
struct drm_psb_private *dev_priv = dev->dev_private;
int ret;
struct backlight_properties props;
memset(&props, 0, sizeof(struct backlight_properties));
props.max_brightness = 100;
props.type = BACKLIGHT_PLATFORM;
cdv_backlight_device = backlight_device_register("psb-bl",
NULL, (void *)dev, &cdv_ops, &props);
if (IS_ERR(cdv_backlight_device))
return PTR_ERR(cdv_backlight_device);
ret = cdv_backlight_setup(dev);
if (ret < 0) {
backlight_device_unregister(cdv_backlight_device);
cdv_backlight_device = NULL;
return ret;
}
cdv_backlight_device->props.brightness = 100;
cdv_backlight_device->props.max_brightness = 100;
backlight_update_status(cdv_backlight_device);
dev_priv->backlight_device = cdv_backlight_device;
return 0;
}
#endif
/*
* Provide the Cedarview specific chip logic and low level methods
* for power management
*
* FIXME: we need to implement the apm/ospm base management bits
* for this and the MID devices.
*/
static inline u32 CDV_MSG_READ32(uint port, uint offset)
{
int mcr = (0x10<<24) | (port << 16) | (offset << 8);
uint32_t ret_val = 0;
struct pci_dev *pci_root = pci_get_bus_and_slot(0, 0);
pci_write_config_dword(pci_root, 0xD0, mcr);
pci_read_config_dword(pci_root, 0xD4, &ret_val);
pci_dev_put(pci_root);
return ret_val;
}
static inline void CDV_MSG_WRITE32(uint port, uint offset, u32 value)
{
int mcr = (0x11<<24) | (port << 16) | (offset << 8) | 0xF0;
struct pci_dev *pci_root = pci_get_bus_and_slot(0, 0);
pci_write_config_dword(pci_root, 0xD4, value);
pci_write_config_dword(pci_root, 0xD0, mcr);
pci_dev_put(pci_root);
}
#define PSB_APM_CMD 0x0
#define PSB_APM_STS 0x04
#define PSB_PM_SSC 0x20
#define PSB_PM_SSS 0x30
#define PSB_PWRGT_GFX_MASK 0x3
#define CDV_PWRGT_DISPLAY_CNTR 0x000fc00c
#define CDV_PWRGT_DISPLAY_STS 0x000fc00c
static void cdv_init_pm(struct drm_device *dev)
{
struct drm_psb_private *dev_priv = dev->dev_private;
u32 pwr_cnt;
int i;
dev_priv->apm_base = CDV_MSG_READ32(PSB_PUNIT_PORT,
PSB_APMBA) & 0xFFFF;
dev_priv->ospm_base = CDV_MSG_READ32(PSB_PUNIT_PORT,
PSB_OSPMBA) & 0xFFFF;
/* Force power on for now */
pwr_cnt = inl(dev_priv->apm_base + PSB_APM_CMD);
pwr_cnt &= ~PSB_PWRGT_GFX_MASK;
outl(pwr_cnt, dev_priv->apm_base + PSB_APM_CMD);
for (i = 0; i < 5; i++) {
u32 pwr_sts = inl(dev_priv->apm_base + PSB_APM_STS);
if ((pwr_sts & PSB_PWRGT_GFX_MASK) == 0)
break;
udelay(10);
}
pwr_cnt = inl(dev_priv->ospm_base + PSB_PM_SSC);
pwr_cnt &= ~CDV_PWRGT_DISPLAY_CNTR;
outl(pwr_cnt, dev_priv->ospm_base + PSB_PM_SSC);
for (i = 0; i < 5; i++) {
u32 pwr_sts = inl(dev_priv->ospm_base + PSB_PM_SSS);
if ((pwr_sts & CDV_PWRGT_DISPLAY_STS) == 0)
break;
udelay(10);
}
}
/**
* cdv_save_display_registers - save registers lost on suspend
* @dev: our DRM device
*
* Save the state we need in order to be able to restore the interface
* upon resume from suspend
*
* FIXME: review
*/
static int cdv_save_display_registers(struct drm_device *dev)
{
return 0;
}
/**
* cdv_restore_display_registers - restore lost register state
* @dev: our DRM device
*
* Restore register state that was lost during suspend and resume.
*
* FIXME: review
*/
static int cdv_restore_display_registers(struct drm_device *dev)
{
return 0;
}
static int cdv_power_down(struct drm_device *dev)
{
return 0;
}
static int cdv_power_up(struct drm_device *dev)
{
return 0;
}
/* FIXME ? - shared with Poulsbo */
static void cdv_get_core_freq(struct drm_device *dev)
{
uint32_t clock;
struct pci_dev *pci_root = pci_get_bus_and_slot(0, 0);
struct drm_psb_private *dev_priv = dev->dev_private;
pci_write_config_dword(pci_root, 0xD0, 0xD0050300);
pci_read_config_dword(pci_root, 0xD4, &clock);
pci_dev_put(pci_root);
switch (clock & 0x07) {
case 0:
dev_priv->core_freq = 100;
break;
case 1:
dev_priv->core_freq = 133;
break;
case 2:
dev_priv->core_freq = 150;
break;
case 3:
dev_priv->core_freq = 178;
break;
case 4:
dev_priv->core_freq = 200;
break;
case 5:
case 6:
case 7:
dev_priv->core_freq = 266;
default:
dev_priv->core_freq = 0;
}
}
static int cdv_chip_setup(struct drm_device *dev)
{
cdv_get_core_freq(dev);
gma_intel_opregion_init(dev);
psb_intel_init_bios(dev);
REG_WRITE(PORT_HOTPLUG_EN, 0);
REG_WRITE(PORT_HOTPLUG_STAT, REG_READ(PORT_HOTPLUG_STAT));
return 0;
}
/* CDV is much like Poulsbo but has MID like SGX offsets and PM */
const struct psb_ops cdv_chip_ops = {
.name = "GMA3600/3650",
.accel_2d = 0,
.pipes = 2,
.crtcs = 2,
.sgx_offset = MRST_SGX_OFFSET,
.chip_setup = cdv_chip_setup,
.crtc_helper = &cdv_intel_helper_funcs,
.crtc_funcs = &cdv_intel_crtc_funcs,
.output_init = cdv_output_init,
#ifdef CONFIG_BACKLIGHT_CLASS_DEVICE
.backlight_init = cdv_backlight_init,
#endif
.init_pm = cdv_init_pm,
.save_regs = cdv_save_display_registers,
.restore_regs = cdv_restore_display_registers,
.power_down = cdv_power_down,
.power_up = cdv_power_up,
};