mirror of
https://github.com/torvalds/linux.git
synced 2024-12-06 11:01:43 +00:00
1ab54a936d
We removed 8250_acpi in 2.6.17. If we don't have PNPACPI turned on, we won't find any ACPI serial devices, so mention this requirement in the troubleshooting part of the documentation. CONFIG_PNPACPI is already turned on in all the relevant defconfigs. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Acked-by: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
152 lines
6.4 KiB
Plaintext
152 lines
6.4 KiB
Plaintext
SERIAL DEVICE NAMING
|
|
|
|
As of 2.6.10, serial devices on ia64 are named based on the
|
|
order of ACPI and PCI enumeration. The first device in the
|
|
ACPI namespace (if any) becomes /dev/ttyS0, the second becomes
|
|
/dev/ttyS1, etc., and PCI devices are named sequentially
|
|
starting after the ACPI devices.
|
|
|
|
Prior to 2.6.10, there were confusing exceptions to this:
|
|
|
|
- Firmware on some machines (mostly from HP) provides an HCDP
|
|
table[1] that tells the kernel about devices that can be used
|
|
as a serial console. If the user specified "console=ttyS0"
|
|
or the EFI ConOut path contained only UART devices, the
|
|
kernel registered the device described by the HCDP as
|
|
/dev/ttyS0.
|
|
|
|
- If there was no HCDP, we assumed there were UARTs at the
|
|
legacy COM port addresses (I/O ports 0x3f8 and 0x2f8), so
|
|
the kernel registered those as /dev/ttyS0 and /dev/ttyS1.
|
|
|
|
Any additional ACPI or PCI devices were registered sequentially
|
|
after /dev/ttyS0 as they were discovered.
|
|
|
|
With an HCDP, device names changed depending on EFI configuration
|
|
and "console=" arguments. Without an HCDP, device names didn't
|
|
change, but we registered devices that might not really exist.
|
|
|
|
For example, an HP rx1600 with a single built-in serial port
|
|
(described in the ACPI namespace) plus an MP[2] (a PCI device) has
|
|
these ports:
|
|
|
|
pre-2.6.10 pre-2.6.10
|
|
MMIO (EFI console (EFI console
|
|
address on builtin) on MP port) 2.6.10
|
|
========== ========== ========== ======
|
|
builtin 0xff5e0000 ttyS0 ttyS1 ttyS0
|
|
MP UPS 0xf8031000 ttyS1 ttyS2 ttyS1
|
|
MP Console 0xf8030000 ttyS2 ttyS0 ttyS2
|
|
MP 2 0xf8030010 ttyS3 ttyS3 ttyS3
|
|
MP 3 0xf8030038 ttyS4 ttyS4 ttyS4
|
|
|
|
CONSOLE SELECTION
|
|
|
|
EFI knows what your console devices are, but it doesn't tell the
|
|
kernel quite enough to actually locate them. The DIG64 HCDP
|
|
table[1] does tell the kernel where potential serial console
|
|
devices are, but not all firmware supplies it. Also, EFI supports
|
|
multiple simultaneous consoles and doesn't tell the kernel which
|
|
should be the "primary" one.
|
|
|
|
So how do you tell Linux which console device to use?
|
|
|
|
- If your firmware supplies the HCDP, it is simplest to
|
|
configure EFI with a single device (either a UART or a VGA
|
|
card) as the console. Then you don't need to tell Linux
|
|
anything; the kernel will automatically use the EFI console.
|
|
|
|
(This works only in 2.6.6 or later; prior to that you had
|
|
to specify "console=ttyS0" to get a serial console.)
|
|
|
|
- Without an HCDP, Linux defaults to a VGA console unless you
|
|
specify a "console=" argument.
|
|
|
|
NOTE: Don't assume that a serial console device will be /dev/ttyS0.
|
|
It might be ttyS1, ttyS2, etc. Make sure you have the appropriate
|
|
entries in /etc/inittab (for getty) and /etc/securetty (to allow
|
|
root login).
|
|
|
|
EARLY SERIAL CONSOLE
|
|
|
|
The kernel can't start using a serial console until it knows where
|
|
the device lives. Normally this happens when the driver enumerates
|
|
all the serial devices, which can happen a minute or more after the
|
|
kernel starts booting.
|
|
|
|
2.6.10 and later kernels have an "early uart" driver that works
|
|
very early in the boot process. The kernel will automatically use
|
|
this if the user supplies an argument like "console=uart,io,0x3f8",
|
|
or if the EFI console path contains only a UART device and the
|
|
firmware supplies an HCDP.
|
|
|
|
TROUBLESHOOTING SERIAL CONSOLE PROBLEMS
|
|
|
|
No kernel output after elilo prints "Uncompressing Linux... done":
|
|
|
|
- You specified "console=ttyS0" but Linux changed the device
|
|
to which ttyS0 refers. Configure exactly one EFI console
|
|
device[3] and remove the "console=" option.
|
|
|
|
- The EFI console path contains both a VGA device and a UART.
|
|
EFI and elilo use both, but Linux defaults to VGA. Remove
|
|
the VGA device from the EFI console path[3].
|
|
|
|
- Multiple UARTs selected as EFI console devices. EFI and
|
|
elilo use all selected devices, but Linux uses only one.
|
|
Make sure only one UART is selected in the EFI console
|
|
path[3].
|
|
|
|
- You're connected to an HP MP port[2] but have a non-MP UART
|
|
selected as EFI console device. EFI uses the MP as a
|
|
console device even when it isn't explicitly selected.
|
|
Either move the console cable to the non-MP UART, or change
|
|
the EFI console path[3] to the MP UART.
|
|
|
|
Long pause (60+ seconds) between "Uncompressing Linux... done" and
|
|
start of kernel output:
|
|
|
|
- No early console because you used "console=ttyS<n>". Remove
|
|
the "console=" option if your firmware supplies an HCDP.
|
|
|
|
- If you don't have an HCDP, the kernel doesn't know where
|
|
your console lives until the driver discovers serial
|
|
devices. Use "console=uart, io,0x3f8" (or appropriate
|
|
address for your machine).
|
|
|
|
Kernel and init script output works fine, but no "login:" prompt:
|
|
|
|
- Add getty entry to /etc/inittab for console tty. Look for
|
|
the "Adding console on ttyS<n>" message that tells you which
|
|
device is the console.
|
|
|
|
"login:" prompt, but can't login as root:
|
|
|
|
- Add entry to /etc/securetty for console tty.
|
|
|
|
No ACPI serial devices found in 2.6.17 or later:
|
|
|
|
- Turn on CONFIG_PNP and CONFIG_PNPACPI. Prior to 2.6.17, ACPI
|
|
serial devices were discovered by 8250_acpi. In 2.6.17,
|
|
8250_acpi was replaced by the combination of 8250_pnp and
|
|
CONFIG_PNPACPI.
|
|
|
|
|
|
|
|
[1] http://www.dig64.org/specifications/DIG64_PCDPv20.pdf
|
|
The table was originally defined as the "HCDP" for "Headless
|
|
Console/Debug Port." The current version is the "PCDP" for
|
|
"Primary Console and Debug Port Devices."
|
|
|
|
[2] The HP MP (management processor) is a PCI device that provides
|
|
several UARTs. One of the UARTs is often used as a console; the
|
|
EFI Boot Manager identifies it as "Acpi(HWP0002,700)/Pci(...)/Uart".
|
|
The external connection is usually a 25-pin connector, and a
|
|
special dongle converts that to three 9-pin connectors, one of
|
|
which is labelled "Console."
|
|
|
|
[3] EFI console devices are configured using the EFI Boot Manager
|
|
"Boot option maintenance" menu. You may have to interrupt the
|
|
boot sequence to use this menu, and you will have to reset the
|
|
box after changing console configuration.
|