/* * NCR 5380 defines * * Copyright 1993, Drew Eckhardt * Visionary Computing * (Unix consulting and custom programming) * drew@colorado.edu * +1 (303) 666-5836 * * DISTRIBUTION RELEASE 7 * * For more information, please consult * * NCR 5380 Family * SCSI Protocol Controller * Databook * NCR Microelectronics * 1635 Aeroplaza Drive * Colorado Springs, CO 80916 * 1+ (719) 578-3400 * 1+ (800) 334-5454 */ /* * $Log: NCR5380.h,v $ */ #ifndef NCR5380_H #define NCR5380_H #include <linux/interrupt.h> #ifdef AUTOSENSE #include <scsi/scsi_eh.h> #endif #define NCR5380_PUBLIC_RELEASE 7 #define NCR53C400_PUBLIC_RELEASE 2 #define NDEBUG_ARBITRATION 0x1 #define NDEBUG_AUTOSENSE 0x2 #define NDEBUG_DMA 0x4 #define NDEBUG_HANDSHAKE 0x8 #define NDEBUG_INFORMATION 0x10 #define NDEBUG_INIT 0x20 #define NDEBUG_INTR 0x40 #define NDEBUG_LINKED 0x80 #define NDEBUG_MAIN 0x100 #define NDEBUG_NO_DATAOUT 0x200 #define NDEBUG_NO_WRITE 0x400 #define NDEBUG_PIO 0x800 #define NDEBUG_PSEUDO_DMA 0x1000 #define NDEBUG_QUEUES 0x2000 #define NDEBUG_RESELECTION 0x4000 #define NDEBUG_SELECTION 0x8000 #define NDEBUG_USLEEP 0x10000 #define NDEBUG_LAST_BYTE_SENT 0x20000 #define NDEBUG_RESTART_SELECT 0x40000 #define NDEBUG_EXTENDED 0x80000 #define NDEBUG_C400_PREAD 0x100000 #define NDEBUG_C400_PWRITE 0x200000 #define NDEBUG_LISTS 0x400000 #define NDEBUG_ANY 0xFFFFFFFFUL /* * The contents of the OUTPUT DATA register are asserted on the bus when * either arbitration is occurring or the phase-indicating signals ( * IO, CD, MSG) in the TARGET COMMAND register and the ASSERT DATA * bit in the INITIATOR COMMAND register is set. */ #define OUTPUT_DATA_REG 0 /* wo DATA lines on SCSI bus */ #define CURRENT_SCSI_DATA_REG 0 /* ro same */ #define INITIATOR_COMMAND_REG 1 /* rw */ #define ICR_ASSERT_RST 0x80 /* rw Set to assert RST */ #define ICR_ARBITRATION_PROGRESS 0x40 /* ro Indicates arbitration complete */ #define ICR_TRI_STATE 0x40 /* wo Set to tri-state drivers */ #define ICR_ARBITRATION_LOST 0x20 /* ro Indicates arbitration lost */ #define ICR_DIFF_ENABLE 0x20 /* wo Set to enable diff. drivers */ #define ICR_ASSERT_ACK 0x10 /* rw ini Set to assert ACK */ #define ICR_ASSERT_BSY 0x08 /* rw Set to assert BSY */ #define ICR_ASSERT_SEL 0x04 /* rw Set to assert SEL */ #define ICR_ASSERT_ATN 0x02 /* rw Set to assert ATN */ #define ICR_ASSERT_DATA 0x01 /* rw SCSI_DATA_REG is asserted */ #ifdef DIFFERENTIAL #define ICR_BASE ICR_DIFF_ENABLE #else #define ICR_BASE 0 #endif #define MODE_REG 2 /* * Note : BLOCK_DMA code will keep DRQ asserted for the duration of the * transfer, causing the chip to hog the bus. You probably don't want * this. */ #define MR_BLOCK_DMA_MODE 0x80 /* rw block mode DMA */ #define MR_TARGET 0x40 /* rw target mode */ #define MR_ENABLE_PAR_CHECK 0x20 /* rw enable parity checking */ #define MR_ENABLE_PAR_INTR 0x10 /* rw enable bad parity interrupt */ #define MR_ENABLE_EOP_INTR 0x08 /* rw enable eop interrupt */ #define MR_MONITOR_BSY 0x04 /* rw enable int on unexpected bsy fail */ #define MR_DMA_MODE 0x02 /* rw DMA / pseudo DMA mode */ #define MR_ARBITRATE 0x01 /* rw start arbitration */ #ifdef PARITY #define MR_BASE MR_ENABLE_PAR_CHECK #else #define MR_BASE 0 #endif #define TARGET_COMMAND_REG 3 #define TCR_LAST_BYTE_SENT 0x80 /* ro DMA done */ #define TCR_ASSERT_REQ 0x08 /* tgt rw assert REQ */ #define TCR_ASSERT_MSG 0x04 /* tgt rw assert MSG */ #define TCR_ASSERT_CD 0x02 /* tgt rw assert CD */ #define TCR_ASSERT_IO 0x01 /* tgt rw assert IO */ #define STATUS_REG 4 /* ro */ /* * Note : a set bit indicates an active signal, driven by us or another * device. */ #define SR_RST 0x80 #define SR_BSY 0x40 #define SR_REQ 0x20 #define SR_MSG 0x10 #define SR_CD 0x08 #define SR_IO 0x04 #define SR_SEL 0x02 #define SR_DBP 0x01 /* * Setting a bit in this register will cause an interrupt to be generated when * BSY is false and SEL true and this bit is asserted on the bus. */ #define SELECT_ENABLE_REG 4 /* wo */ #define BUS_AND_STATUS_REG 5 /* ro */ #define BASR_END_DMA_TRANSFER 0x80 /* ro set on end of transfer */ #define BASR_DRQ 0x40 /* ro mirror of DRQ pin */ #define BASR_PARITY_ERROR 0x20 /* ro parity error detected */ #define BASR_IRQ 0x10 /* ro mirror of IRQ pin */ #define BASR_PHASE_MATCH 0x08 /* ro Set when MSG CD IO match TCR */ #define BASR_BUSY_ERROR 0x04 /* ro Unexpected change to inactive state */ #define BASR_ATN 0x02 /* ro BUS status */ #define BASR_ACK 0x01 /* ro BUS status */ /* Write any value to this register to start a DMA send */ #define START_DMA_SEND_REG 5 /* wo */ /* * Used in DMA transfer mode, data is latched from the SCSI bus on * the falling edge of REQ (ini) or ACK (tgt) */ #define INPUT_DATA_REG 6 /* ro */ /* Write any value to this register to start a DMA receive */ #define START_DMA_TARGET_RECEIVE_REG 6 /* wo */ /* Read this register to clear interrupt conditions */ #define RESET_PARITY_INTERRUPT_REG 7 /* ro */ /* Write any value to this register to start an ini mode DMA receive */ #define START_DMA_INITIATOR_RECEIVE_REG 7 /* wo */ #define C400_CONTROL_STATUS_REG NCR53C400_register_offset-8 /* rw */ #define CSR_RESET 0x80 /* wo Resets 53c400 */ #define CSR_53C80_REG 0x80 /* ro 5380 registers busy */ #define CSR_TRANS_DIR 0x40 /* rw Data transfer direction */ #define CSR_SCSI_BUFF_INTR 0x20 /* rw Enable int on transfer ready */ #define CSR_53C80_INTR 0x10 /* rw Enable 53c80 interrupts */ #define CSR_SHARED_INTR 0x08 /* rw Interrupt sharing */ #define CSR_HOST_BUF_NOT_RDY 0x04 /* ro Is Host buffer ready */ #define CSR_SCSI_BUF_RDY 0x02 /* ro SCSI buffer read */ #define CSR_GATED_53C80_IRQ 0x01 /* ro Last block xferred */ #if 0 #define CSR_BASE CSR_SCSI_BUFF_INTR | CSR_53C80_INTR #else #define CSR_BASE CSR_53C80_INTR #endif /* Number of 128-byte blocks to be transferred */ #define C400_BLOCK_COUNTER_REG NCR53C400_register_offset-7 /* rw */ /* Resume transfer after disconnect */ #define C400_RESUME_TRANSFER_REG NCR53C400_register_offset-6 /* wo */ /* Access to host buffer stack */ #define C400_HOST_BUFFER NCR53C400_register_offset-4 /* rw */ /* Note : PHASE_* macros are based on the values of the STATUS register */ #define PHASE_MASK (SR_MSG | SR_CD | SR_IO) #define PHASE_DATAOUT 0 #define PHASE_DATAIN SR_IO #define PHASE_CMDOUT SR_CD #define PHASE_STATIN (SR_CD | SR_IO) #define PHASE_MSGOUT (SR_MSG | SR_CD) #define PHASE_MSGIN (SR_MSG | SR_CD | SR_IO) #define PHASE_UNKNOWN 0xff /* * Convert status register phase to something we can use to set phase in * the target register so we can get phase mismatch interrupts on DMA * transfers. */ #define PHASE_SR_TO_TCR(phase) ((phase) >> 2) /* * The internal should_disconnect() function returns these based on the * expected length of a disconnect if a device supports disconnect/ * reconnect. */ #define DISCONNECT_NONE 0 #define DISCONNECT_TIME_TO_DATA 1 #define DISCONNECT_LONG 2 /* * These are "special" values for the tag parameter passed to NCR5380_select. */ #define TAG_NEXT -1 /* Use next free tag */ #define TAG_NONE -2 /* * Establish I_T_L nexus instead of I_T_L_Q * even on SCSI-II devices. */ /* * These are "special" values for the irq and dma_channel fields of the * Scsi_Host structure */ #define SCSI_IRQ_NONE 255 #define DMA_NONE 255 #define IRQ_AUTO 254 #define DMA_AUTO 254 #define PORT_AUTO 0xffff /* autoprobe io port for 53c400a */ #define FLAG_HAS_LAST_BYTE_SENT 1 /* NCR53c81 or better */ #define FLAG_CHECK_LAST_BYTE_SENT 2 /* Only test once */ #define FLAG_NCR53C400 4 /* NCR53c400 */ #define FLAG_NO_PSEUDO_DMA 8 /* Inhibit DMA */ #define FLAG_DTC3181E 16 /* DTC3181E */ #ifndef ASM struct NCR5380_hostdata { NCR5380_implementation_fields; /* implementation specific */ struct Scsi_Host *host; /* Host backpointer */ unsigned char id_mask, id_higher_mask; /* 1 << id, all bits greater */ unsigned char targets_present; /* targets we have connected to, so we can call a select failure a retryable condition */ volatile unsigned char busy[8]; /* index = target, bit = lun */ #if defined(REAL_DMA) || defined(REAL_DMA_POLL) volatile int dma_len; /* requested length of DMA */ #endif volatile unsigned char last_message; /* last message OUT */ volatile Scsi_Cmnd *connected; /* currently connected command */ volatile Scsi_Cmnd *issue_queue; /* waiting to be issued */ volatile Scsi_Cmnd *disconnected_queue; /* waiting for reconnect */ volatile int restart_select; /* we have disconnected, used to restart NCR5380_select() */ volatile unsigned aborted:1; /* flag, says aborted */ int flags; unsigned long time_expires; /* in jiffies, set prior to sleeping */ int select_time; /* timer in select for target response */ volatile Scsi_Cmnd *selecting; struct delayed_work coroutine; /* our co-routine */ #ifdef NCR5380_STATS unsigned timebase; /* Base for time calcs */ long time_read[8]; /* time to do reads */ long time_write[8]; /* time to do writes */ unsigned long bytes_read[8]; /* bytes read */ unsigned long bytes_write[8]; /* bytes written */ unsigned pendingr; unsigned pendingw; #endif #ifdef AUTOSENSE struct scsi_eh_save ses; #endif }; #ifdef __KERNEL__ #define dprintk(a,b) do {} while(0) #define NCR5380_dprint(a,b) do {} while(0) #define NCR5380_dprint_phase(a,b) do {} while(0) #if defined(AUTOPROBE_IRQ) static int NCR5380_probe_irq(struct Scsi_Host *instance, int possible); #endif static int NCR5380_init(struct Scsi_Host *instance, int flags); static void NCR5380_exit(struct Scsi_Host *instance); static void NCR5380_information_transfer(struct Scsi_Host *instance); #ifndef DONT_USE_INTR static irqreturn_t NCR5380_intr(int irq, void *dev_id); #endif static void NCR5380_main(struct work_struct *work); static void __maybe_unused NCR5380_print_options(struct Scsi_Host *instance); #ifdef NDEBUG static void NCR5380_print_phase(struct Scsi_Host *instance); static void NCR5380_print(struct Scsi_Host *instance); #endif static int NCR5380_abort(Scsi_Cmnd * cmd); static int NCR5380_bus_reset(Scsi_Cmnd * cmd); static int NCR5380_queue_command(struct Scsi_Host *, struct scsi_cmnd *); static int __maybe_unused NCR5380_show_info(struct seq_file *, struct Scsi_Host *); static int __maybe_unused NCR5380_write_info(struct Scsi_Host *instance, char *buffer, int length); static void NCR5380_reselect(struct Scsi_Host *instance); static int NCR5380_select(struct Scsi_Host *instance, Scsi_Cmnd * cmd, int tag); #if defined(PSEUDO_DMA) || defined(REAL_DMA) || defined(REAL_DMA_POLL) static int NCR5380_transfer_dma(struct Scsi_Host *instance, unsigned char *phase, int *count, unsigned char **data); #endif static int NCR5380_transfer_pio(struct Scsi_Host *instance, unsigned char *phase, int *count, unsigned char **data); #if (defined(REAL_DMA) || defined(REAL_DMA_POLL)) #if defined(i386) || defined(__alpha__) /** * NCR5380_pc_dma_setup - setup ISA DMA * @instance: adapter to set up * @ptr: block to transfer (virtual address) * @count: number of bytes to transfer * @mode: DMA controller mode to use * * Program the DMA controller ready to perform an ISA DMA transfer * on this chip. * * Locks: takes and releases the ISA DMA lock. */ static __inline__ int NCR5380_pc_dma_setup(struct Scsi_Host *instance, unsigned char *ptr, unsigned int count, unsigned char mode) { unsigned limit; unsigned long bus_addr = virt_to_bus(ptr); unsigned long flags; if (instance->dma_channel <= 3) { if (count > 65536) count = 65536; limit = 65536 - (bus_addr & 0xFFFF); } else { if (count > 65536 * 2) count = 65536 * 2; limit = 65536 * 2 - (bus_addr & 0x1FFFF); } if (count > limit) count = limit; if ((count & 1) || (bus_addr & 1)) panic("scsi%d : attempted unaligned DMA transfer\n", instance->host_no); flags=claim_dma_lock(); disable_dma(instance->dma_channel); clear_dma_ff(instance->dma_channel); set_dma_addr(instance->dma_channel, bus_addr); set_dma_count(instance->dma_channel, count); set_dma_mode(instance->dma_channel, mode); enable_dma(instance->dma_channel); release_dma_lock(flags); return count; } /** * NCR5380_pc_dma_write_setup - setup ISA DMA write * @instance: adapter to set up * @ptr: block to transfer (virtual address) * @count: number of bytes to transfer * * Program the DMA controller ready to perform an ISA DMA write to the * SCSI controller. * * Locks: called routines take and release the ISA DMA lock. */ static __inline__ int NCR5380_pc_dma_write_setup(struct Scsi_Host *instance, unsigned char *src, unsigned int count) { return NCR5380_pc_dma_setup(instance, src, count, DMA_MODE_WRITE); } /** * NCR5380_pc_dma_read_setup - setup ISA DMA read * @instance: adapter to set up * @ptr: block to transfer (virtual address) * @count: number of bytes to transfer * * Program the DMA controller ready to perform an ISA DMA read from the * SCSI controller. * * Locks: called routines take and release the ISA DMA lock. */ static __inline__ int NCR5380_pc_dma_read_setup(struct Scsi_Host *instance, unsigned char *src, unsigned int count) { return NCR5380_pc_dma_setup(instance, src, count, DMA_MODE_READ); } /** * NCR5380_pc_dma_residual - return bytes left * @instance: adapter * * Reports the number of bytes left over after the DMA was terminated. * * Locks: takes and releases the ISA DMA lock. */ static __inline__ int NCR5380_pc_dma_residual(struct Scsi_Host *instance) { unsigned long flags; int tmp; flags = claim_dma_lock(); clear_dma_ff(instance->dma_channel); tmp = get_dma_residue(instance->dma_channel); release_dma_lock(flags); return tmp; } #endif /* defined(i386) || defined(__alpha__) */ #endif /* defined(REAL_DMA) */ #endif /* __KERNEL__ */ #endif /* ndef ASM */ #endif /* NCR5380_H */