Add support to configure Enhanced Transient Response Enable (ETR)
and Sensitivity Selection based on maximum current i.e. expected
load on that rail.
Maxim recommended as:
- Enable ETR with high sensitivity (75mV/us) for 0 to 9A expected loads,
- Enable ETR with low sensitivity (150mV/us) for 9A to 12A expected loads.
- Disable ETR for expected load > 12A.
These recommendation will be configured for MAX77621 when maximum load
is provided through regulator constraint for maximum current from platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MAX8973/MAX77621 feature an Enhanced Transient Response(ETR)
circuit that is enabled through software. The enhanced transient
response reduces the voltage droop during large load steps by
temporarily allowing all three phases to fire in unison, slewing
total inductor current faster than would normally be possible if
all three phases continued to operate 120deg out of phase. The
enhanced transient response detector features two selectable
sensitivity settings, which select the output voltage slew rate
during load transients that triggers the ETR circuit. The sensitivity
of the ETR detector is set by the CKADV[1:0] bits in the CONTROL2
register.
Add support to configure the ETR through platform data from DT.
Update the DT binding document accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control flag for the bias control is MAX8973_CONTROL_BIAS_ENABLE
rather than MAX8973_BIAS_ENABLE which is macro for the bits in
register.
Fix this typo.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix trivial typo.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maxim MAX77621 device is high-efficiency, three-phase,
DC-DC step-down switching regulator delivers peak
output currents up to 16A. This device is extension of
MAX8973 and compatible with the register definition.
The MAX77621 has the SHUTDOWN pin which is EN pin on the
MAX8973. On MAX77621, the SHUTDOWN pin (active low) reset
device register to its POR/OTP value. The voltage output
is enabled when SHUTDONW pin is HIGH and EN bit on VOUT
register is HIGH.
For MAX8973, VOUT is enabled when EN bit or EN pin is high.
Add support of the MAX77621 device on max8973 regulator driver
with following changes:
- Make sure SHUTDOWN pin is set HIGH through GPIO calls if
GPIO from AP connected to SHUTDOWN pin provided.
- Enable/disable the rail through register access only.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator core framework support the configuration of ramp
delay reading from platform specific regulator data via the
regulator callback ops.
Instead of reading regulator init data on driver and setting
ramp delay, use the callback to achieve this.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX8973 supports the voltage output enable/disable through its EN
pin. This EN pin can be connected through GPIO from host processor.
Add support to provide GPIO number from platform/DT and if it is
valid GPIO then enable external control default.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some platform specific parameter required to configure
the device like enable external control, DVS gpio etc.
Add DT parsing of such properties to make platform specific data.
Update DT binding doc accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To find that dvs-gpio is valid or not, gpio API gpio_is_valid()
can be directly used instead of intermediate variable.
Removing the extra variable and using the gpio_is_valid().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If platform data has dvs-gpio value 0 as default/unset then
make this as invalid gpio so that function gpio_is_valid()
can return false on this case.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In MAX8973, BIAS enable control bit is used for changing the startup time
for voltage output. The startup delay is 240us (typ) when the BIASEN
bit is set to 0. The startup delay is reduced to 20us (typ) when the
BIASEN bit is set to 1.
Pass the enable_time through regulator descriptor based on this flag.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_get_regulator_init_data() function is used to extract the regulator
init_data but information on how to extract certain data is defined in the
static regulator descriptor (e.g: how to map the hardware operating modes).
Add a const struct regulator_desc * parameter to the function signature so
the parsing logic could use the information in the struct regulator_desc.
of_get_regulator_init_data() relies on of_get_regulation_constraints() to
actually extract the init_data so it has to pass the struct regulator_desc
but that is modified on a later patch.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'struct regulator_dev *rdev' of 'struct max8973_chip' isn't used
anywhere in the driver so it can be removed safely.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds primitive DT support to the max8973 regulator driver. None
of the configuration parameters, supported in the platform data are yet
available in DT, therefore no configuration is performed if booting with
no platform data. This means, that DT instantiation can only be used on
boards, where no run-time configuration of the chip is required. In such
cases the driver can be used to scale its output voltage. In the future
support for configuration parameters should be added.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the max8973 regulator driver uses a single static struct of
regulator operations for all chip instances, but can overwrite some of its
members depending on configuration. This will affect all other MAX8973
instances on the system. This patch fixes this bug by allocating a separate
copy of the struct for each chip instance.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code overrides control1 variable when setting ramp delay bits.
Fix it by just setting ramp_delay bits.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If external control is enabled then do not provide regulator
enable/disable apis.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAXIM MAX8973 high-efficiency, three phase, DC-DC step-down
switching regulator delievers up to 9A of output current. Each
phase operates at a 2MHz fixed frequency with a 120 deg shift
from the adjacent phase, allowing the use of small magnetic
component.
Add regulator driver for this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>