This adds the wl1251_sdio module, enabling the SDIO interface for
wl1251, as used by the Google G1 phone and others.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This creates a module called wl1251_spi.ko which contains just the
SPI-specific code. The core remains in the module wl1251.ko.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change moves all of the spi specific code from main.c into
spi.c. The module initialization code also moves, but common
code for initializing mac80211 etc. stays in main.c, as this will
eventually form a common library module also used by wl1251_sdio.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The same partition setting code can be used for both SPI and SDIO
modes, if we remove the spi-specific commands and use the more
generic buffer write routines. Do that and move it to io.c
since it deals with register/memory address offsets.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce an ops struct with read, write, and reset functions to
abstract away the details of the wl1251 bus interface. Doing this
will allow SDIO to coexist with SPI by supplying its own I/O
routines.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove a dependency on the bus-specific struct device by using wiphy_dev
when requesting firmware.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to eventually support wl1251 spi and sdio interfaces, move
the register and memory transfer functions to a common file. Also
rename wl1251_spi_mem_{read,write} to indicate its common usage.
We still use spi_read internally until SDIO interface is introduced
so nothing functional should change here.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fixed addresses are not used in wl1251, only in wl1271. So it can
be safely removed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI uses the beacon RSSI for its operation.
Update this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmask can be obtained directly from ath_hw.
Also, use a helper macro for comparing CTLs - this improves readability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Write CCK power-per-rate array always and report
correct TX power to regulatory.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps the antenna configuration mechanism
for 4K chips.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A subsequent patch would use these for configuring
antennae on AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
regChainOffset is always zero, remove it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add eeprom_def.c, eeprom_4k.c and eeprom_9287.c
This improves maintainability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the wl1271 driver in the Kconfig and in the
Makefile.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver supports the wl1271 chipset from Texas Instruments based on the
WiLink(tm) 6.0 mobile platform. Support for wl1273 should be relatively easy
to add. This chipset is designed for embedded devices, with good powersaving
capabilities. The wl1271 chipset is the successor of wl1251 and supports the
802.11b/g/n standards, but currently this driver supports only b/g.
More information about this chipset can be found here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12762&contentId=29993
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TKIP support was added, we stored the keys separately to avoid
issues when both TKIP and WEP keys are sent to the driver.
We need to consolidate the storage to convert to cfg80211, so do this
first and try iron out the issues.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will need this from the cfg80211 disassociate call.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows the disassociation to be called via cfg80211.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we store the keys for cfg80211, the sequence lengths will also be
stored. So avoid assuming the sequence lengths at this level.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps in the refactorring required to convert the driver to
cfg80211.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a boolean value set based on firmware capabilities, so move the
variable to the capabilities section and reduce the structure size.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update a comment that still says IEEE80211_IF_TYPE instead of NL80211_IFTYPE.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tkip hw support uncovered a bug in b43_write_probe_resp_template : it is
writing at the wrong shm offset, it is in the B43_SHM_SH_TKIPTSCTTAK
zone. Remove b43_write_probe_resp_template, b43_write_probe_resp_plcp
and b43_write_probe_resp_plcp because the probe response offload is
currently not supported by mac80211.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of HostFlags defines in the LP-PHY code.
Fix fallout from the IEEE80211_IF_TYPE to NL80211_IFTYPE change.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add B2063 radio init code and tables for LP-PHY.
Rename structures common between B2062 and B2063 to B206X.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw uses its own LED stuff so let rename its LED
stuff as such.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to set pspoll filter on ath9k on AP mode but
we no longer need this mode specific check as mac80211
now does the check for us and informs us when we should
enable pspoll through FIF_PSPOLL.
Cc: Igor Perminov <igor.perminov@inbox.ru>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let ath5k_chan_set() always call ath5k_reset().
This fixes the bug that we don't
get any packets in monitor mode after:
ifconfig wlan0 down
iwconfig wlan0 mode monitor channel 1
ifconfig wlan0 up
but they arrive after
iwconfig wlan0 channel 2
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change rt2x00_rf_read() and rt2x00_rf_write() to subtract 1 from the rf
register number. This is needed because the rf registers are enumerated
starting with one. The size of the rf register cache is just enough to
hold all registers, so writing to the highest register was corrupting
memory. Add a check to make sure that the rf register number is valid.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@kernel.org
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Traffic received with a priority tag (VID = 0) and non-zero priority value was
incorrectly handled by the VLAN packet code path due to a check on zero for
the whole VLAN tag instead of just the VID.
This patch masked out the priority field when checking the vlan tag for
received VLAN packets.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return the ddp->len in ixgbe_fcoe_ddp() to indicate the length of data that
have been DDPed. However, it is possible that the length is 0, e.g., for SCSI
READ, the FCP_RSP may come back w/ SCSI status 0x28 as Task Set Full with no FCP
data for DDP. In ixgbe_fcoe_ddp(), we return 0 to indicate not passing DDPed
packets to upper layer. Therefore in the case of ddp->len being 0 upon FCP_RSP,
we do not want to return the 0 ddp->len as we want FCP_RSP to be always
delivered to the upper layer. This patch fixes this bug by setting rc only if
ddp->len is non-zero.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I did not introduce new lines over 80 chars. I even eliminated some of
them.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Defer napi resouce allocation to device attach.
o Free napi resources and delete napi during detach.
This ensures right behavior across firmware reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove private workqueue in the driver, move all
scheduled tasks to keventd workqueues. This makes
ports (interfaces) of same / different NIC boards
independent, in terms of their link watchdog and
reset tasks.
o Move quick checks for link status and temperature
in timer callback, schedule watchdog task only if
link status changed or temperature reached critical
threshold.
This also fixes deadlock when thermal panic occurs,
watchdog work was flushing workqueue that it was
sitting on.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently setting rx-usecs when the interface is in legacy interrupt
mode it is not immediate. We were only setting EITR for each MSIx
vector and since this count would be zero for legacy mode it wasn't
set until after a reset. This patch corrects that by checking what
mode we are in and then setting EITR accordingly.
Signed-off-by: Don Skidmore <donald.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created with
the ip tool ...
The invocation of 'ip link add type can' lead to an oops as the standard rtnl
newlink function was called:
http://bugzilla.kernel.org/show_bug.cgi?id=13954
This patch adds a private newlink function for the CAN device driver interface
that unconditionally returns -EOPNOTSUPP.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I fixed up my mac driver, which relatives to previous
mac driver actually in the tree.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also avoids a potential buffer overflow in case the very first
receive descriptor fails to allocate, as an index of -1 would be used
afterwards. Kudos to Roel Kluin for pointing this out and providing an
initial patch.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro DRV_NAME contains "korina", the field dev->name points to the
actual interface name. So messages were formerly prefixed with
'korinaeth2:' (on my system).
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_alloc_skb() fails on the first iteration of the allocation loop,
then we end up writing before the start of the array.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the code to a more logical place and beautifying it. No real change in
behavior.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ieee_fc to u16 instead of u32 and re-arrange the link parameters
structures
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable bmac access while working with emac and keep the single lane SerDes in
reset while working with 4 lanes XGXS
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this check, when running out of memory, we will see PSOD's in
bnx2x_init_fill() when doing a memset(). This is because at that time,
bp->gunzip_buf is not pointing to a valid allocated space.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved the dmae_command from the heap to the stack. This will save 56
bytes per bnx2x structure. As a side benefit, we can also reduce the
time the dmae_mutex is held. This is because do we not need to hold
this mutex when setting up the dmae command. The memory where is dmae
command is stored is not a shared resource and doesn not need to be
protected.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move printing of version from probe to the init function
Rather then checking if this is the first module probe call to print
the version of the driver only once, the statement is moved to the init
function of the module where init is only called once
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions bnx2x_get_pcie_width() and bnx2x_get_pcie_speed() were
combined into bnx2x_get_pcie_width_speed() so that there is only
1 PCI read to PCICFG_OFFSET + PCICFG_LINK_CONTROL rather then 2 reads.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, bnx2x_init_dev calls pci_set_drvdata(pdev, NULL)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a given ring is running out of space, the FW can send pause towards the
network. When working with multi-queues, when one queue is getting out of space
it can block all other queues. The preferred scheme is to send pause frames only
when running out of the shared internal chip buffers and if a given queue cannot
place a packet on the host, it will drop it. Since some users might want to work
in drop-less mode, allowing changing the behavior as a module parameter.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code should not have resided in the driver. Now that we have a new
interface, this logic can reside in the application that whishes to upgrade the
PHY FW
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 operations that the driver needs to support to allow applications to
access the PHY FW (on top of the MDC/MDIO access). Since those are essentially
nvram access commands, adding them to the ethtool -E interface.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Ben Hutchings <bhutchings@solarflare.com>, using the MDC/MDIO
IOCTL
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding CL73 support to the built in PHY in the 5771x device. Also supporting
fallbacks to CL73 if the link partner does not respond.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM8727 is a dual port PHY. The FW must be loaded in a given order on all
designs - including those which swapped the ports (calling port number zero the
second port)
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid confusion, if the PHY does not have a FW (and so, no FW version) make
sure that the string is NULL.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM8481 does not generate LASI interrupt for 10M, 100M and 1G link, so we
are using LED4 output as the interrupt input to the 57711. This requires some
adaptation in the link interrupt routines
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-function mode, the FW can receive special management control commands
to set the Min/Max BW and the the function link state
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new FW improves the packets per second rate. It required a lot of change in
the FW which implies many changes in the driver to support it. It is now also
possible for the driver to use a separate MSI-X vector for Rx and Tx - this also
add some to the complicity of this change.
All things said - after this patch, practically all performance matrixes show
improvement.
Though Vladislav Zolotarov is not signed on this patch, he did most of the job
and deserves credit for that.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver always:
1. allocate cp->rx_buf_sz + NET_IP_ALIGN
2. map cp->rx_buf_sz
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synced with Realtek's 1.013.00 r8101 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synced with Realtek's 6.011.00 r8169 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synced with Realtek's 6.011.00 r8169 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synced with Realtek's 6.011.00 r8169 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver displays the same 0x18000000 xid for RTL_GIGA_MAC_VER_06
and RTL_GIGA_MAC_VER_05 whereas the former ought to be identified as
0x98000000.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Vincent Pelletier <plr.vincent@gmail.com>.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any events rcvd after interrupts are disabled (in the driver unload path),
must be cleared and notified before the event queues are destroyed
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using "for(tail != head)" to traverse a queue from tail to head
fails in the case of a fully filled queue. Use "for(used != 0)" instead.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear pending tx completions in be_close() (ndo.stop method) so that after
unregister_netdev() calls be_close(), all tx skbs are freed and there are
no more tx completions when txq is destroyed.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the following 'make includecheck' warning:
drivers/net/smc911x.h: mach/dma.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve myri10ge parity error detection and recovery:
1) Don't restore PCI config space to a rebooted NIC until AFTER the
host is quiescent.
2) Let myri10ge_close() know the NIC is dead, so it won't waste time
waiting for a dead nic to respond to MXGEFW_CMD_ETHERNET_DOWN
3) When the NIC is quiet (link down, or otherwise idle link) use
a pci config space read to detect a rebooted NIC. Otherwise
we might never notice that a NIC rebooted
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
request_mem_region should be used with release_mem_region, not request_region.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r2@
expression start;
@@
request_mem_region(start,...)
@b2@
expression r2.start;
@@
request_region(start,...)
@depends on !b2@
expression r2.start;
expression E;
@@
- release_region
+ release_mem_region
(start,E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the following 'make includecheck' warning:
drivers/net/pcmcia/axnet_cs.c: linux/etherdevice.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the following 'make includecheck' warning:
drivers/net/cs89x0.c: asm/irq.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general in this file, it is the status field, not the state field, that
contains values like OPEN and CLOSED. Indeed, in the first error case, it
is the field status that is initialized. I have thus assumed that all of
the error handling code should be the same, and moved it to the end of the
function to emphasize its commonality.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this series of tests the constants have the form XRXMAC_STATUS, except
in this one case. The values of XRXMAC_STAT_MSK_RXOCTET_CNT_EXP and
XRXMAC_STATUS_RXOCTET_CNT_EXP are furthermore the same.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 57921c312e.
On request from John Linville:
It has been shown to create a new problem. There is work
towards a solution to that one, but it isn't a simple
clean-up.
Signed-off-by: David S. Miller <davem@davemloft.net>
pernet data should allocated first and freed last
on module init/exit routines otherwise it's possible
to have unserialized calls to packet handling routines.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
queue == __AR9170_NUM_TXQ would cause a bug on the next line.
found by Smatch ( http://repo.or.cz/w/smatch.git ).
Cc: stable@kernel.org
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ar9170-2.fw was missing, the driver erroneously complained
about missing the initialization values file ar9170-1.fw...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the length is less or equal to frag_prefix_size in the first iteration
we write skb_frags_rx[-1] and read from priv->frag_info[-1]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent read from cards[-1] when no card was found.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An `options[cards_found]' that equals `sizeof(options_mapping)' is already beyond
the array.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vlan has been enabled. ifdown followed by ifup will lost hardware
related state.
Also remove duplicated operation in gfar_vlan_rx_register().
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bank offset was being incorrectly calculated on ICH9 parts with a bank
size of 8K (instead of the more common 4K bank) which would cause any NVM
writes to be done on the wrong address after switching from bank 1 to bank
0. Additionally, assume we are meant to use bank 0 if a valid bank is not
detected, and remove the unnecessary acquisition of the SW/FW/HW semaphore
when writing to the shadow ram version of the NVM image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ICHx parts, write the EXTCNF_CTRL.SWFLAG bit once when trying to
acquire the SW/FW/HW semaphore instead of multiple times to prevent the
hardware from having problems (especially for systems with manageability
enabled), and extend the timeout for the hardware to set the SWFLAG bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 82599, packet split has to be disabled for FCoE direct data placement.
However, this is only required on received queues allocated for FCoE. This
patch adds a per ring flags to indicate if packet split is disabled on a
per queue basis, particularly for FCoE, as packet split must be disabled
for large receive using direct data placement (DDP).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing the register index of the corresponding rx_ring and find
the way back to get to corresponding rx_ring in ixgbe_configure_srrctl(),
simplify the function ixgbe_configure_srrctl() by passing the rx_ring into
it. Then the register index for that rx_ring is already available from
rx_ring->reg_idx.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is, parts of the ioctl runs under the RTNL and parts of
it do not. The unlocked section is still protected by the BKL,
but there can be subtle races. For example, Eric Biederman and
Paul Moore observed that if two threads tried to create two tun
devices on the same file descriptor, then unexpected results
may occur.
As there isn't anything in the ioctl that is expected to sleep
indefinitely, we can prevent this from occurring by extending
the RTNL lock coverage.
This also allows to get rid of the BKL.
Finally, I changed tun_get_iff to take a tun device in order to
avoid calling tun_put which would dead-lock as it also tries to
take the RTNL lock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f0b3fbeae1 ("FEC Buffer rework")
breaks transmission of packets where the skb data buffer is not memory
aligned according to FEC_ALIGNMENT. It incorrectly passes to
dma_sync_single() the buffer address directly from the skb, instead of
the address calculated for use (which may be the skb address or one of
the bounce buffers).
It seems there is no use converting the cpu address of the buffer to
a physical either, since dma_map_single() expects the cpu address and
will return the dma address to use in the descriptor. So remove the use
of __pa() on the buffer address as well.
This patch is against 2.6.30-rc5. This breakage is a regression over
2.6.30, which does not have this problem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
strlcpy() will always null terminate the string.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <csnook@redhat.com>
Cc: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
io[i] is read before the bounds check on i, order should be reversed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older Gcc compilers (3.4.5 tested) need additional hints in order to get
the packing of the rxpd structure (which contains a 16 bit union)
correct on the ARM processor.
struct txpd does not need these hints since it contains a 32 bit union
that packs naturally.
Signed-off-by: R.J.Dunlop <rdunlop@guralp.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to unregister our ieee80211_hw before resetting the chip, as
the former causes firmware commands to be issued which will time out
once the chip has been reset.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we go into out-of-memory and fail to allocate skbuffs to
refill the receive ring with, rxq_process can end up running into
a receive ring entry that is marked as host-owned but doesn't have
an associated skbuff. If this happens, we must break out of the
rx processing loop instead of trying to process the descriptor.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
> channel_index loops up to IPW_SCAN_CHANNELS, but is used after being
> incremented. This might be able to access 1 past the end of the array
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use 1:1 mapping between QPs and SRQs on receive side,
so additional indirection level not required. Allocated the receive
buffers for the RSS QPs.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in using more QPs then actual number of receive rings.
If the RSS function for two streams gives the same result modulo number
of rings, they will arrive to the same RX ring anyway.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the net device is identified as "sender" (number of sent packets
is higher then the number of received packets and the incoming packets are
small), set the moderation time to its low limit.
We do it because the incoming packets are acks, and we don't want to delay them
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hibernation is unsupported for now, which meets the actual
implementation in the driver. For free/thaw, the chip's D2 state should
be entered.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The datasheet say "When not enabling packing, the MinFrag value must
remain at 0". Do not set value to RxFragSize register if
TC35815_USE_PACKEDBUFFER disabled.
This is not a bugfix. No real problem reported on this.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Miss_Cnt register is cleared by reading. Accumulate its value to
rx_missed_errors count.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current timeout value is too short for very high-load condition
which jiffies might jump up in busy-loop.
Also add minimum delay before checking completion of MDIO.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear Int_BLEx / Int_FDAEx after (not before) processing Rx interrupt.
This will reduce number of unnecessary interrupts.
Also print rx error messages only if netif_msg_rx_err() enabled.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems Rx_StripCRC cause trouble on recovering from the BLEx (Buffer
List Exhaust) or FDAEx (Free Descriptor Area Exhaust) condition.
Do not use it.
Also bump version number up.
Reported-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 88045b3cf0
cxgb3: fix mac index mapping
Override the mac index computation for the gen2 adapter,
as each port is expected to use index 0.
introduces a regression on 2 port 1G adapter
as its xauicfg vpd value is null.
Add a check on the device id.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found this old card which was not supported, and physically
looks similar to the other 3C905B we have (9055).
After adding the IDs it seems to work fine (MII report, dhcp, scp, ...)
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version number for any bug reports from end users.
Signed-off-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements prefetching of skb->data from a copy of the pointer
in the descriptor (which is already in the L1 cache at this point). This
improves netperf rx performance (netperf -L 0,0 -c -H 192.168.254.2 -- -M
131072 -m 131072) by 4.9% on a P4 Xeon host.
Signed-off-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prefetches RxD descriptors which helps to lower the latency of a
cache miss in vxge_hw_ring_rxd_next_completed. This lowers the % of CPU
time used by vxge_hw_ring_rxd_next_completed() where the descriptor is
accessed in profiling netperf on a P4 Xeon from 1.5% to 1.0%.
Signed-off-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wmb() is extremely heavy on x86. The semantics required in the driver are
provided by mmiowb(), so use that and improve tx performance on P4 Xeons by
5-10%.
Signed-off-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a case in the transmit completion code which was resulting
in pktgen hanging at the end of a run. The cause is due to the fact that
the ->cb[] area of an skb cannot be used in a network driver's transmit
path, as that area belongs to the network protocol. Pktgen hangs, as it
sends out the same packet multiple times, and vxge's use of this area of
the skb for a temporary list can only add the packet to the temporary list
once (while it may be on the queue many times). The fix is to remove this
abuse of skb->cb[]. Instead, skb pointers are placed into a temporary
stack array, and then free outside of the tx lock. This retains the smp
optimization of doing dev_kfree_skb() outside of the tx lock.
Signed-off-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vxge driver will drop a packet in its transmit function if the number
of TxDs available hits 0. Instead of doing that, simply stop the transmit
queue when transmitting a packet with the last available TxD.
Signed-off-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb priority to vlan-qos egress mapping that can be configured using
set_egress_map with vconfig is overriden by the DCB code in the driver.
This patch allows this existing mechanism to work and will increase the
configuration flexibility of DCB mode on Linux.
A hierarchy of configuration is:
1. Modifies the ixgbe_select_queue() routine for DCB mode to return the
priority value from the VLAN tag. It will normally be zero, unless the egress
priority map has modified it. This will get packets into the correct queue and
result in the queue_mapping field being set correctly.
2. Any tc filter which modifies queue_mapping will be honored, as the filters
are handled after the vlan egress map is handled.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a bug fix to avoid system going into a bad state when
driver is loaded in context of kdump kernel. The patch fixes the issue
by performing a soft reset of pci function at probe time.
Signed-off-by: sarveshwarb <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to handle aggregate packets from firmware.
Local TCP flows are automatically identified by firmware
based on the dest IP hash added by driver for local IP
addresses.
The packets are sent down on the jumbo rx ring.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary offsetof calulations on these structures:
netxen_board_info, netxen_user_old_info, netxen_new_user_info.
The offsets into the flash are fixed, don't need to be calculated.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the calculation of remaining header length in TSO
over vlan device case. This was inadvertently missed
out in patch 028afe7198 ("netxen: add vlan
tx acceleration support").
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with version 0.5.1, cpmac is no longer broken.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch slows down the MDIO_ALIVE busy waiting to let
switches and PHY come up after reset. Previous loop was
too quick for IC+175C and ADM6996C/L switches to come up.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for fixed PHY connected in MII mode
to cpmac. We allow external and dumb_switch module parameters
to override the PHY detection process since they are always connected
with MDIO bus identifier 0. This lets fixed PHYs to be detected
correctly and be connected to the their corresponding MDIO
bus identifier.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the wrong MDIO bus identifier which was
set to 0 unconditionaly, suitable for external switches while
it is actually 1 for PHYs different than external switches
which are autodetected.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dma mask calculation that caps at 63-bit addressing even
when firmware advertises full 64-bit support.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/wireless/ath/ath9k/eeprom.o
drivers/net/wireless/ath/ath9k/eeprom.c: In function ‘ath9k_hw_AR9287_check_eeprom’:
drivers/net/wireless/ath/ath9k/eeprom.c:2866: warning: comparison of distinct pointer types lacks a cast
Cc: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will finalize this after some driver core changes, for now
we leave this unsupported.
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used later to add support for ar9271.
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't use typdefs on ath9k, remove that _t.
Cc: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_keyreset() has a spurious check for ah->curchan..
remove it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The keycache reset will not fail as right above we ensure
to set the sc->keymax to be <= ah->caps.keycache_size. Just remove
this dangling check.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If hw initialization fails (ath9k_hw_init()) on ath_init_softc()
we bail out and call ath9k_hw_detach(). The call ath9k_hw_detach()
is conditional though as ath9k_hw_init() could itself have called
ath9k_hw_detach(). Just describing this is itself a brain twister.
Avoid this nonsense by removing ath9k_hw_detach() from ath9k_hw_init().
Upon hw initialization failure we expect the callers to take care of
the cleanup.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kfree(NULL) works so remove all those branches which check
for it before kfree()'ing on ath9k_hw_rfdetach().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We re-label the device driver initialization routines from the
ath_softc, the "Software Carrier" fillers. This should make it
clearer what each of these do.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During initialization ath9k tends to use "attach" to when we
initialize hardware due to the fact we used to attach a "HAL".
The notion of a HAL is long gone, so lets just be clear on what
we are doing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes reading the hardware initialization process
easier to understand. The new helpers added are:
ath9k_hw_init_cal_settings()
ath9k_hw_init_mode_regs()
ath9k_hw_init_mode_gain_regs()
ath9k_hw_init_11a_eeprom_fix()
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're now propagating the -ENOMEM error so there is no need to
keep a debug message there now.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reflects better what we are actually doing there.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reflects better what we are actually doing there.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The softc is cached and set within the ath_hw struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_attach() was going first through some device id verifier,
and then calling some other helper which was doing the real hardware
initialization. Lets just do the devid checks within the real worker
by calling a helper ath9k_hw_devid_supported().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this in case attach and friends try to get back to
ah from the softc somehow.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets us trim one argument off of hw initializer routines.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets us simplify attach code and arguments passed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were never propagating hw initialization errors, lets
do that now and also use -EOPNOTSUPP when device revision is
not supported yet.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes adding new hw revisions a one line change here.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will clean this up next to just use a switch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
UMAC only allows us to set default key for WEP and auth type is
not 802.1X or RSNA. This patch fixes iwmc3200wifi for 802.1X with
WEP104.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should only set the static_key flag for open and legacy
authentication types. It should not be set for 802.1X and TKIP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwm->umac_profile->sec.flags is set by iwm_set_wpa_version and
checked by iwm_set_auth_type. The patch changes the order to
make the flag used correctly.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement baseband init for rev.0 and rev.1 LP PHYs. Convert boardflags_hi values to defines.
Implement b43_phy_copy for easier copying between registers, as needed by LP-PHY init.
Signed-off-by: Gábor Stefanik<netrolller.3d@gmail.com>
Cc: Michael Buesch<mb@bu3sch.de>
Cc: Larry Finger<larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unloading rt61pci can leave the device in such state that reloading
rt61pci would fail to reinitialize it. Bogus data would be read from
the EEPROM and the RF version won't be recognized.
It appears that unloading rt61pci with power saving enabled would have
such effect. To initialize the device properly, SOFT_RESET_CSR should
be set to the same value as rt61pci_config_ps() uses to wake up the
device.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As shown in http://thread.gmane.org/gmane.linux.kernel.wireless.general/36497,
mac80211 has a bug that allows a call to the TX routine after the queues have
been stopped. This situation will only occur under extreme stress. Although
b43legacy does not crash when this condition occurs, it does generate a WARN_ON
and also logs a queue overrun message. This patch recognizes b43legacy is not
at fault and logs a message only when the most verbose debugging mode is
enabled. In the unlikely event that the queue is not stopped when the DMA
queue becomes full, then a warning is issued.
This patch is based on the one used by b43.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add code to handle IW_AUTH_PRIVACY_INVOKED and IW_AUTH_RX_UNENCRYPTED_EAPOL
cases in lbs_set_auth() function in libertas code.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
version info in sysfs had been determined to be unnecessary as it
is already provided in syslog info. nvm version is added to syslog
version info as a debug level message to provide all info that was
in the version sysfs data.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the support for deprecated devices. These devices are
engineering samples and no longer supported by the uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x00 2x2 NIC, two types of Power Amplifier are available.
In order for uCode to apply correct tx power,
driver needs to program the CSR_GP_DRIVER_REG register and
let uCode know the type of PA.
If driver do not program CSR_GP_DRIVER_REG register (default to 0),
then it is uCode's decision for tx power
2x2 Hybrid card: use both internal and external PA
2x2 IPA(Internal Power Amplifier) card: internal PA only
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resolve an issue in which out-dated fields in iwl_cmd_meta
could be used for later hardware commands.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tkip hw support uncovered a bug in b43_write_probe_resp_template : it is
writing at the wrong shm offset, it is in the B43_SHM_SH_TKIPTSCTTAK zone. This
patch comments these writes.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
