The internal PHYs in the mv88e6390 switch have a temperature sensor.
It uses a different register layout to other PHY currently supported.
It also has an errata, in that some reads of the sensor result in bad
values. So a number of reads need to be made, and the average taken.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mask argument for phy_modify() in several locations was inverted.
Fixes: fea23fb591 ("net: phy: convert read-modify-write to phy_modify()")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert read-modify-write sequences in at803x, Marvell and core phylib
to use phy_modify() to ensure safety.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For paged accesses to be truely safe, we need to hold the bus lock to
prevent anyone else gaining access to the registers while we modify
them.
The phydev->lock mutex does not do this: userspace via the MII ioctl
can still sneak in and read or write any register while we are on a
different page, and the suspend/resume methods can be called by a
thread different to the thread polling the phy status.
Races have been observed with mvneta on SolidRun Clearfog with phylink,
particularly between the phylib worker reading the PHYs status, and
the thread resuming mvneta, calling phy_start() which then calls
through to m88e1121_config_aneg_rgmii_delays(), which tries to
read-modify-write the MSCR register:
CPU0 CPU1
marvell_read_status_page()
marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE)
...
m88e1121_config_aneg_rgmii_delays()
set_page(MII_MARVELL_MSCR_PAGE)
phy_read(phydev, MII_88E1121_PHY_MSCR_REG)
marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE);
...
phy_write(phydev, MII_88E1121_PHY_MSCR_REG)
The result of this is we end up writing the copper page register 21,
which causes the copper PHY to be disabled, and the link partner sees
the link immediately go down.
Solve this by taking the bus lock instead of the PHY lock, thereby
preventing other accesses to the PHY while we are accessing other PHY
pages.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Observed on the 88e1512 in SGMII-to-Copper mode, negotiating pause
is unreliable. While the pause bits can be set in the advertisment
register, they clear shortly after negotiation with a link partner
commences irrespective of the cause of the negotiation.
While these bits may be correctly conveyed to the link partner on the
first negotiation, a subsequent negotiation (eg, due to negotiation
restart by the link partner, or reconnection of the cable) will result
in the link partner seeing these bits as zero, while the kernel
believes that it has advertised pause modes.
This leads to the local kernel evaluating (eg) symmetric pause mode,
while the remote end evaluates that we have no pause mode capability.
Since we can't guarantee the advertisment, disable pause mode support
with this PHY when used in SGMII-to-Copper mode.
The 88e1510 in RGMII-to-Copper mode appears to behave correctly.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
88E1145 also need this autoneg errata.
Fixes: f289978835 ("net: phy: marvell: Limit errata to 88m1101")
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
When in SGMII-to-Copper mode, the fiber page is used for the MAC facing
link, and does not require configuration of the fiber auto-negotiation
settings. Avoid trying.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
uncovered another bug in the Marvell PHY driver, which broke the
Marvell OpenRD platform. It relies on the bootloader configuring the
RGMII delays and does not specify a phy-mode in its device tree. The
PHY driver should only configure RGMII delays if the phy mode
indicates it is using RGMII. Without anything in device tree, the
mv643xx Ethernet driver defaults to GMII.
Fixes: 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was supposed to be a bitwise OR but there is a || vs | typo.
Fixes: 864dc729d5 ("net: phy: marvell: Refactor m88e1121 RGMII delay configuration")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1116r has code to set downshift. Refactor this into a helper, so
in future other marvell PHYs can use it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the init functions unilaterally enable set auto cross over
without using the helper. Make use of the helper, and respect the
phydev MDI configuration.
Clean up the #define used while setting polarity, and the other
functions of the bits in the register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turns out that MII_M1116R_CONTROL_REG_MAC is the same as
MII_88E1121_PHY_MSCR_REG. Refactor the code to set the RGMII delays
into a shared helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is repeated a few times. Refactor into a helped.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is repeated for different PHY versions. Put it into a
help and call when needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using an open coded equivalent, use the core
genphy_soft_reset() function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert spaces to tabs where appropriate, and fix up some otherwise
odd indentation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add set_loopback in phy_driver, which is used by MAC
driver to enable or disable phy loopback. it also add a generic
genphy_loopback function, which use BMCR loopback bit to enable
or disable loopback.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give back all modes advertised by the link partner. This change brings
the marvell phy driver in line with all other phy drivers.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
functions m88e1510_get_temp_critical, m88e1510_set_temp_critical and
m88e1510_get_temp_alarm can be made static as they not need to be
in global scope.
Cleans up sparse warnings:
"symbol 'm88e1510_get_temp_alarm' was not declared. Should it be static?"
"symbol 'm88e1510_get_temp_critical' was not declared. Should it be
static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring all the page names together, remove the repeats, and make them
uniform.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a common pattern of first reading the currently selected page
and then changing to another page. Add a helper to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
EXT_ADDR_PAGE is the same meaning as MII_MARVELL_PHY_PAGE, i.e. change
page. Replace it will calls to the helpers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace magic numbers for PHY pages with symbolic names.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88m1101 has an errata when configuring autoneg. However, it was
being applied to many other Marvell PHYs as well. Limit its scope to
just the 88m1101.
Fixes: 76884679c6 ("phylib: Add support for Marvell 88e1111S and 88e1145")
Reported-by: Daniel Walker <danielwa@cisco.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes the code a bit more readable, and solves quite a few checkpatch
warnings of lines longer than 80 characters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break big functions up by using a number of smaller helper
function. Solves some of the over 80 lines warnings, by reducing the
indentation level.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid multiple assignments
Comparisons should place the constant on the right side of the test
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the extra blank lines, add one in where recommended.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use net style comment blocks, and wrap one block with long lines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hwmon temperature sensor devices is registered using a devm_hwmon
API call. The marvell_release() would then manually free the device,
not using a devm_hmon API, resulting in the device being removed
twice, leading to a crash in kernfs_find_ns() during the second
removal.
Remove the manual removal, which makes marvell_release() empty, so
remove it as well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 0b04680fda ("phy: marvell: Add support for temperature sensor")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e1545 PHYs are discrete Marvell PHYs, found in a quad package on
the zii-devel-b board. Add support for it to the Marvell PHY driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 Ethernet switch has internal PHYs. These PHYs don't have
an model ID in the ID2 register. So the MDIO driver in the switch
intercepts reads to this register, and returns the switch family ID.
Extend the Marvell PHY driver by including this ID, and treat the PHY
as a 88E1540.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One line was apparently pasted incorrectly during a new feature patch:
drivers/net/phy/marvell.c:2090:15: error: initialized field overwritten [-Werror=override-init]
.features = PHY_GBIT_FEATURES,
I'm removing the extraneous line here to avoid the W=1 warning and restore
the previous flags value, and I'm slightly reordering the lines for consistency
to make it less likely to happen again in the future. The ordering in the
array is still not the same as in the structure definition, instead I picked
the order that is most common in this file and that seems to make more sense
here.
Fixes: 0b04680fda ("phy: marvell: Add support for temperature sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell PHYs have an inbuilt temperature sensor. Add hwmon
support for this sensor.
There are two different variants. The simpler, older chips have a 5
degree accuracy. The newer devices have 1 degree accuracy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an Marvell 88E1512 PHY is connected to a nic in SGMII mode, the
fiber page is used for the SGMII host-side connection. The PHY driver
notices that SUPPORTED_FIBRE is set, so it tries reading the fiber page
for the link status, and ends up reading the MAC-side status instead of
the outgoing (copper) link. This leads to incorrect results reported
via ethtool.
If the PHY is connected via SGMII to the host, ignore the fiber page.
However, continue to allow the existing power management code to
suspend and resume the fiber page.
Fixes: 6cfb3bcc06 ("Marvell phy: check link status in case of fiber link.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers to have an eth_tp_mdix_ctrl to indicate what is the configured
MDI setting, and read eth_tp_mdi to indicate what is the current status,
Add new parameter mdix_ctrl in phy_device structure and fix driver.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of remembering if the page was changed, just compare the current
page to the saved one. This is easier and has the advantage to save a
register write if the page was already restored.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions used standards registers in a different page
for both interfaces: copper and fiber.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be correctly initilized, the fiber interface needs
to be configured via autonegociation registers which use
some customs options or registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the fiber receiver error counter in the
statistics. Rename the current counter which is for copper errors to
phy_receive_errors_copper, so it is easy to distinguish copper from
fiber.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
For concerned phy, the fiber link is checked before the copper link.
According to datasheet, the link which is up is enabled.
If both links are down, copper link would be used.
To detect fiber link status, we used the real time status
because of troubles with the copper method.
Tested with Marvell 88E1512.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1111 currently uses the generic marvell config ANEG function.
This function has a sequence accessing Page 5 and Register 31,
both of which are not defined or reserved for this PHY.
Hence this patch adds a new config ANEG function for Marvell 88E1111
without these erroneous accesses.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring the PHY LED registers for the Marvell 88E1510 and others is
not possible, because regardless of the values in marvell,reg-init, it
is later overridden in m88e1121_config_aneg with a non-standard default.
This patch moves that default configuration to .config_init to allow
setting the LED configuration through marvell,reg-init in the device
tree, which should override said default if it exists.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
