This patch removes 4965 from iwl4965_frame struct and handling functions.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965_tx_queue_update_write_ptr to
iwl_txq_update_write_ptr. This is a preparation for moving to iwl-tx.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new handler get_hw_cmd_size in hcmd_utils,
which should adjust the size of the command sent to the microcode
according to the current nic.
It also changes the RXON flow to make usage of this new handler.
The patch also adds iwl_rxon_cmd structure which is supperset for
5000 HW and 4965.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965_tx_info to iwl_tx_info.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965_queue to iwl_queue.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fills the needed data about HW capabilities in matters of
possible HT Tx MCS.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch follows the 11n spec in separation between Tx and Rx MCS
capabilities. Up until now, when configuring the HT possible set of Tx
MCS only Rx MCS were considered, assuming they are the same as the Tx MCS.
This patch fixed this by looking at low level driver Tx capabilities.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the contant of iwl4965_nic_start to the only place it is
being used.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes an old eeprom comment in probe flow.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[PATCH, take 2] libertas: reduce command retry time
In the normal case, an unsuccessful command would be retried for 10*5 seconds,
or 10*10 seconds in the worst case. This patch reduces this to 3*3 seconds,
or 3*10 seconds in the worst case.
I also reduced the time it takes to start a new command downloaded.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will create the following entry:
/sys/class/net/mshX
-- boot_options
| |-- ...
| `-- channel
...
... which I overlooked on my previous patch.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on a patch from Shailendra Govardhan and Brian Cavagnolo.
It extends the MESH_CONFIG command to configure non-volatile parameters on
libertas devices that support them (e.g. OLPC Active Antenna).
This patch only implements the driver/firmware interface.
See http://dev.laptop.org/ticket/6823 for minimal testing results and known
issues.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We weren't properly handling multicast on the mesh interface. Fix that,
which involves setting up the hardware to use the union of dev->mc_list
for both eth%d and msh%d devices.
This means we can't do it directly from ->set_multicast_list() because
we'd need to lock the other device to read its list, and we can't do
that because it might deadlock. So punt the actual work to keventd.
Also, invoke the same when taking an interface down; for some reason the
core calls ->set_multicast_list while IFF_UP is still set in dev->flags
when we're taking it down, so its addresses don't get removed then.
We also convert MAC_MULTICAST_ADR to a direct command while we're at it,
removing one more entry from the big switch statement in the deprecated
lbs_prepare_and_send_command() function.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the deprecated lbs_prepare_and_send_command() function for a
command which it doesn't understand is an error; complain loudly about
it even when we're not debugging.
The mesh stats bug, where we converted MESH_ACCESS to a direct command
but accidentally missed one user which was still trying to do it through
lbs_prepare_and_send_command(), would have been caught a lot quicker if
we'd done this sooner. Such bugs aren't entirely unlikely in future too,
as we convert more code to stop using this function.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the pending removal of the tx_control structure
we can merge the RX and TX entry private data structure
in advance. This will temporarily increase the required
memory for the queue, but that overhead will only be limited.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the rxdesc structure is properly memsetted before passed to
the driver. This means we don't have to reinitialize the flags
and dev_flags fields in the drivers again.
This will prevent problems when the rxdone handler is adding
flags in a earlier status and will make the code look nicer
when we are adding more read attributes in the rxdone handler
in the driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split rt2x00lib_write_tx_desc() up into a TX descriptor initializor
and TX descriptor writer.
This split is required to properly allow mac80211 to move its
tx_control structure into the skb->cb array.
The rt2x00queue_create_tx_descriptor() function will read all tx control
information and convert it into a rt2x00 TX descriptor information structure.
After that function is complete, we have all information we needed from the
tx control structure and are free to start writing into the skb->cb array
for our own purposes.
rt2x00queue_write_tx_descriptor() will be in charge of really sending
the TX descriptor to the hardware and kicking the TX queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation of replacing the statically allocated data DMA buffers with DMA-mapped
skb's we need to change the TXD handling of the PCI drivers, by moving the programming
of the buffer address fields to the actual TXD writing at TX time, instead of at start-up
time.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to usage of memmove() in rt2x00usb the descriptor can become
corrupted because it is being overwritten by the data part.
Overall having the descriptor in front of the frame is a bad idea,
we can however use the skb->cb array for this task, since that
contains more then enough room to hold the entire descriptor and
preserve the information long enough.
After this we can also cleanup the alignment code a bit to make it
work a bit more flexible to allow for all kinds of odd header lengths.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the integration of the mac80211 multiqueue patches it has become possible that the
mac80211 layer modifies the number of TX queues that is stored inside the ieee80211_hw
structure, especially when multi-queue is not selected.
The rt2x00 drivers are not well suited to handle that situation, as they allocate the
queue structures before mac80211 has modified the number of queues it is going to use,
and also expect the number of allocated queues to match the hardware implementation.
Hence, ensure that rt2x00 maintains by itself the number of queues that the hardware
supports, and, at the same time, making is not dependent on the preservation of contents
inside a mac80211 structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the last remaining information details read from ieee80211_tx_control
in the drivers to the txentry_desc structure. After this we can
remove ieee80211_tx_control from the argument list for the callback function,
which makes it easier when the control information is moved into skb->cb
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx_status enumeration was broken since the introduction
of rt61pci. That driver uses different values to report the
status of the tx action.
This would lead to frames that were reported as success but
actually failed to be send out, or frames that were neither
successfull or failure which were reported as failure.
Fix this by change the TX status reporting and more explicitely
check for failure or success. Note that a third possibility is
added "unknown". Not all hardware (USB) can report the actual
TX status, for rt61pci some frames will receive this status
because the TXdone handler is never called for those frames.
This unknown will now be handled as neither success or failure,
so we no longer increment the failure counter while this conclusion
could not be determined from the real status of the frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove frame_type from skb_frame_desc and pass it
as argument to rt2x00debug_dump_frame().
Change data_len and desc_len to unsigned short
to save another 4 bytes in skb_frame_desc. Note that
this was the only location where the data_len and
desc_len was not yet treated as unsigned short.
This trim is required to help mac80211 with adding
the TX control and TX status informtation into the
skb->cb structure. When that happens, drivers will
have approximately 40 bytes left to use freely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 4-bit reversal flip_4bit is replaced with the bitrev helper
bitrev8 and a 4-bit shift. The B43_WARN is moved to the location
where a register is read from for checking there. The other caller
explicitly passes an array index which is guaranteed to be within range
and so a B43_WARN is not added there.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Reviewed-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath5k_tasklet_rx, both status structures 'rxs' and 'rs' are
initialized at the top of the tasklet, but not within the loop.
If the loop is executed multiple times in the tasklet then the
variables may see changes from previous packets.
For TKIP, this results in 'Invalid Michael MIC' errors if two packets
are processed in the tasklet: rxs.flag gets set to RX_DECRYPTED by
mac80211 when it decrypts the first encrypted packet. The subsequent
packet will have RX_DECRYPTED set upon entry to mac80211, so mac80211
will not try to decrypt it.
We currently initialize all but two fields in the structures, so fix
the other two.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove duplicated include <linux/delay.h> in
drivers/net/wireless/b43/nphy.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
DRIVER SIGNAL MAX NOISE QUAL
-----------------------------------------------------------------
adm8211 unspec(?) 100 n/a missing
at76_usb unspec(?) (?) unused missing
ath5k dBm dBm percent rssi
b43legacy dBm dBm percent jssi(?)
b43 dBm dBm percent jssi(?)
iwl-3945 dBm dBm percent snr+more
iwl-4965 dBm dBm percent snr+more
p54 unspec 127 n/a missing
rt2x00 dBm n/a percent rssi+tx/rx frame success
rt2400 dBm n/a
rt2500pci dBm n/a
rt2500usb dBm n/a
rt61pci dBm n/a
rt73usb dBm n/a
rtl8180 unspec(?) 65 n/a (?)
rtl8187 unspec(?) 65 (?) noise(?)
zd1211 dB(?) 100 n/a percent
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this adds initial IBSS support for the zydas zd1211rw:
convince driver that it can do IBSS mode. add mac80211 beacon_update callback.
IBSS merge and TSF updates don't work yet, but it makes the driver usable in
ad-hoc networks.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use net_device_stats from net_device structure instead of local.
Kill atmel_get_stats function, because by default it is used
identical internal_stats function from net/core/dev.c
No need to memset stats to 0, because they are allocated by kzalloc.
P.S. Someone should cleanup init_atmel_card function from unneeded
initializations to 0/NULL. Out of scope for this patch.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 <---> mac80211 <----> wpa_supplicant <---> NetworkManager
When a hardware scan is completed and another scan is requested in less
than two seconds, iwlwifi will not do the second scan and will pass the
error code -EAGAIN back to mac80211 where it quickly dies. The error
code is not passed along to the calling program wpa_supplicant. After a
timeout, wpa_supplicant will just give up but it will not know why the
scan failed. This is a weakness in the design.
I ran into this issue when I was trying to figure out why it takes more
an a minute for NetworkManager to connect after Networking has been
disabled and then re-enabled. I found a good deal of unnecessary work
being done because mac80211 requests authentication when the interface
is not configured, the ANY mode. I created an experimental passive
(NOTANY) mode for mac80211 to eliminate this case. Then NetworkManager
became so fast that I ran into the iwlwifi 2 second delay next scan
issue which we are discussing.
The patch resolves the problem by bypassing the delay if the scan request
is a direct scan. It should do less harm to the hardware.
Signed-off-by: Bill Moss <bmoss@CLEMSON.EDU>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a module parameter of fw_restart which determine if
the uCode will be restarted or not in case of error.
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds sysfs version file that displays ucode version
and type.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the levels of debug prints, leaving only one level
in each debug print.
It was anoying and caused unnecessary prints on hot path.
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports the debug_level from sysfs/bus/pci/drivers/iwl4965
to /sys/class/net/wlanX/device/debug_level
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use net_device_stats from net_device structure instead of local.
Changed airo_read_stats function parameter to net_device.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes spinlock priv->lock (apm_ops.init) is used before it has
been initialized.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the 4965 prefix to form iwl_kw and iwl_tx_queue structs,
as they are used mostly in iwlcore now.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits ucode's and driver's shared memory Rx index access to
match 4965 and 5000 offsets.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch leverages mac80211 configure_filter to enable iwl3945
monitor mode.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch leverages mac80211 configure_filter to enable iwl4965
monitor mode.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_4965_init_alive_start to iwl-4965.c.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl-sta into iwl-core.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
