Some bootloaders are broken enough to expose an ATAG_MEM with
a null size. Converting such tag to a memory node leads to
an unbootable system.
Skip over zero sized ATAG_MEM to avoid this situation.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
atags_to_fdt() returns 1 when it fails to find a valid FDT signature.
The CONFIG_ARM_ATAG_DTB_COMPAT code is supposed to retry with another
location, but only does so when the initial call doesn't fail.
Fix this by using the correct condition in the assembly code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The clocks for all DSS slave interfaces were recently changed to "dss_ick" on
OMAP2 and OMAP3, this clock can be autoidled by PRCM. The VENC interface
previously had "dss_54m_fck" as it's clock which couldn't be autoidled, and
hence the OCPIF_SWSUP_IDLE flag was needed.
Remove the OCPIF_SWSUP_IDLE flag from VENC interfaces as it's clock is
now "dss_ick". This allows the PRCM hardware to autoidle the VENC
interface clocks when they are not active, rather than relying on the
software to do it, which can keep the interface clocks active
unnecessarily.
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: add a short description of the fix to the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This reverts commit f9a2f9c3fa. This
commit caused a regression in the I2C hwmod reset on OMAP2/3/4,
logging messages similar to these during boot:
[ 0.200378] omap_hwmod: i2c1: softreset failed (waited 10000 usec)
[ 0.222076] omap_hwmod: i2c2: softreset failed (waited 10000 usec)
While the original patch was intended to fix some reset-related timing
issues, it's believed that these problems were actually fixed by
commit 2800852a07 ("ARM: OMAP2+: hwmod:
Restore sysc after a reset"):
http://marc.info/?l=linux-arm-kernel&m=133410322617245&w=2
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Due to HW limitation, some IPs should not be accessed just after a
softreset. Since the current hwmod sequence is accessing the sysconfig
register just after the reset, it might lead to OCP bus error in
that case.
Add a new field in the sysconfig structure to specify a delay in usecs
needed after doing a softreset.
In the case of the ISS and FDIF modules, the L3 OCP port will be
disconnected upon a SW reset. That issue was confirmed with HW simulation
and an errata should be available soon. The HW recommendation to avoid
that is to wait for 100 OCP clk cycles, before accessing the IP.
Considering the worse case (OPP50), the L3 bus will run at 100 MHz,
so a 1 usec delay is needed. Add an x2 margin to be safe.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: dropped FDIF change for now since the hwmod data is not
yet upstream; the FDIF change will need to be added later once the FDIF
data is merged]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Wake secondary cpu via resched instead of
"Unknown IPI message 0x1"
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add PDMA and MDMA physical base address macros which is
require for EXYNOS5 of_dev_auxdata setup.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: changed dma channel fo mdma1]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fixes the following warning:
warning: 'dma_dmamask' defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
handle_IRQ may briefly cause interrupts to be re-enabled during soft IRQ
processing on the exit path, leading to nested handling of VIC interrupts.
Since the current code does not re-read the VIC_IRQ_STATUS register, this
can lead to multiple invocations of the same interrupt handler and
spurious interrupts to be reported.
This patch changes the VIC interrupt dispatching code to re-read the
status register each time, avoiding duplicate invocations of the same
handler.
Acked-and-Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
commit 8878a539ff was done by me
to make the page fault handler retryable as well as interruptible.
Due to this commit, there is a mistake in the way in which
tsk->[maj|min]_flt counter gets incremented for VM_FAULT_ERROR:
If VM_FAULT_ERROR is returned in the fault flags by handle_mm_fault,
then either maj_flt or min_flt will get incremented. This is wrong
as in the case of a VM_FAULT_ERROR we need to be skip ahead to the
error handling code in do_page_fault.
Added a check after the call to __do_page_fault() to check for
(fault & VM_FAULT_ERROR).
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the following build breakage in v3.4-rc2 that happens
with CONFIG_OMAP_MUX=y:
arch/arm/mach-omap1/mux.c:89:1: error: 'FUNC_MUX_CTRL_9' undeclared here (not in a function)
arch/arm/mach-omap1/mux.c:89:1: error: 'PULL_DWN_CTRL_2' undeclared here (not in a function)
arch/arm/mach-omap1/mux.c:93:1: error: 'FUNC_MUX_CTRL_C' undeclared here (not in a function)
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch is omitted in v2 patch of Jaecheol Lee.
drivers/cpufreq/exynos5250-cpufreq.c: In function 'set_clkdiv':
drivers/cpufreq/exynos5250-cpufreq.c:144: error: 'EXYNOS5_CLKDIV_STATCPU0' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c:144: error: (Each undeclared identifier is reported only once
drivers/cpufreq/exynos5250-cpufreq.c:144: error: for each function it appears in.)
drivers/cpufreq/exynos5250-cpufreq.c:150: error: 'EXYNOS5_CLKDIV_CPU1' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c:152: error: 'EXYNOS5_CLKDIV_STATCPU1' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c: In function 'set_apll':
drivers/cpufreq/exynos5250-cpufreq.c:166: error: 'EXYNOS5_CLKMUX_STATCPU' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c:173: error: 'EXYNOS5_APLL_LOCK' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c: In function 'exynos5250_cpufreq_init':
drivers/cpufreq/exynos5250-cpufreq.c:312: error: 'EXYNOS5_CLKDIV_CPU1' undeclared (first use in this function)
Cc: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This fixes following build error when sound support is selected
on EXYNOS4 platform.
sound/soc/samsung/idma.c: In function ‘idma_close’:
sound/soc/samsung/idma.c:327:11: error: ‘IRQ_I2S0’ undeclared (first use in this function)
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to commit 719a4240("mfd: Remove unused LDO supply field
from WM8994 pdata"), the LDO supply field should be removed from
the initializer.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A bunch of fixes for regressions (and a few other problems) in 3.4-rc1:
* Fix for regression of mach/io.h cleanup on platforms with PCI or PCMCIA
(adding back the include file on those for now)
* AT91 fixes for usb and spi
* smsc911x ethernet fixes for i.MX
* smsc911x fixes for OMAP
* gpio fixes for Tegra
* A handful of build error and warning fixes for various platforms
* cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series, aren't
technically regressions for 3.4, but they're valid fixes and we're still
relatively early in the rc cycle so it seems appropriate to include them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RVTD
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
early v3.4-rc series. Also contains an HSMMC integration refinement
of an earlier hardware bug workaround.
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
ARM: OMAP AM3517/3505: clock data: change EMAC clocks aliases
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP: clock: fix race in disable all clocks
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3xxx: clock data: fix DPLL4 CLKSEL masks
ARM: OMAP3xxx: HSMMC: avoid erratum workaround when transceiver is attached
ARM: OMAP44xx: clockdomain data: correct the emu_sys_clkdm CLKTRCTRL data
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPfWEKAAoJEMePsQ0LvSpLGqIP/1Mvc3O7+Gs97E8BBR7RVkPC
Uo4aM6NMwkCBozC9XLooS12FFCC1k97aLh7IeEhN5qZ8U/FqkF6qIdMTLzJpSsnD
nuL1JLZGAdd+OtxgbVhjd/3cmK2H94K5XozZrKbC2/fypjDRjh40yk6hIH0zvZU6
+OX6r0kRW9HX6gC2+cAPJzKWaSgVimh6KQxRsevL8xbyPm183/vx2U0E1bicsHrY
rSXcQTo0AanDHNX4bSG3lMXiv+hVxYRpzlhJ1ToPN/fRokWXJjp3oycRYVL4A6KE
8MvvSORhf6yVekB+LOESIEmFNisGl/2zuAPFnZBnHzcpvNTvDB57uSPtUeQjXsUK
6MBgW5okGUU9tihP7m8tmP6kbo0tPdZRtBiJP0KDBflLRFAOgrcWiRQL+8jjus0v
ktHt6h3P71D8MoYN74T6x2/0NP49FXA3RVxuKDoaT3nXXkR7IvVNVXPh15zRTPFe
liTrn0U1Bu34HvpAuR8WRO5W0VgT2DTPQNk7WtZkYlyS1WXLAunDW9+Bv1JHS1MH
zeBZf6SNE1kVLWdNkFaYK0pAXHw8epwsUKeI9ZNIX3y9qdamzvafzeKQUjewPbLm
26KOzr3cuwIb7No7sh3fSpJV/Y8YFPCb9MvvzMg5yhfYf2SL4xYrudhSPcCw9gEy
2pCChl33o4AvxjkUEXjZ
=41FI
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a2-for-3.4rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
OMAP clock, powerdomain, clockdomain, and hwmod fixes intended for the
early v3.4-rc series. Also contains an HSMMC integration refinement
of an earlier hardware bug workaround.
* tag 'omap-fixes-a2-for-3.4rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
ARM: OMAP AM3517/3505: clock data: change EMAC clocks aliases
ARM: OMAP: clock: fix race in disable all clocks
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
ARM: OMAP3xxx: clock data: fix DPLL4 CLKSEL masks
ARM: OMAP3xxx: HSMMC: avoid erratum workaround when transceiver is attached
ARM: OMAP44xx: clockdomain data: correct the emu_sys_clkdm CLKTRCTRL data
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With commit c334bc1 (ARM: make mach/io.h include optional), PCMCIA was
broken. PCMCIA depends on __io() returning a valid i/o address, and most
ARM platforms require IO_SPACE_LIMIT be set to 0xffffffff for PCMCIA. This
needs a better fix with a fixed i/o address mapping, but for now we just
restore things to the previous behavior.
This fixes at91, omap1, pxa and sa11xx. pxa needs io.h if PCI is enabled,
but PCMCIA is not. sa11xx already has IO_SPACE_LIMIT set to 0xffffffff,
so it doesn't need an io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com> (pxa270)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Note that this also contains a set of fixes that are not regressions
or oopses to properly deal with the smsc911x regulator issue.
Basically the regulators must be per board file as the regulators
can also come from drivers, such as twl4030. So it's best to dumb
down gpmc-smsc911x.c to not even care about the regulators.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: fix section mismatches in usb-host.c
ARM: OMAP2+: Fix omap2+ build error
ARM: OMAP2+: smsc911x: Add fixed board regulators
ARM: OMAP2+: smsc911x: Remove regulator support from gmpc-smsc911x
ARM: OMAP2+: smsc911x: Remove unused rate calculation
ARM: OMAP2+ smsc911x: Fix possible stale smsc911x flags
ARM: OMAP2+: smsc911x: Remove odd gpmc_cfg/board_data redirection
ARM: OMAP3+: fix oops triggered in omap_prcm_register_chain_handler(v1)
ARM: OMAP2+: OPP: allow OPP enumeration to continue if device is not present
arm: omap3: pm34xx.c: Replace printk() with appropriate pr_*()
arm: omap3: pm34xx.c: Fix omap3_pm_init() error out paths
ARM: OMAP4: Workaround the OCP synchronisation issue with 32K synctimer.
ARM: OMAP4: prm: fix interrupt register offsets
ARM: OMAP: hwmod: Use sysc_fields->srst_shift and get rid of hardcoded SYSC_TYPE2_SOFTRESET_MASK
Fixes the following warning:
warning: 'dma_dmamask' defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In the SYSC_TYPE1_XXX_MASK configuration, SYSC_XXX_SHIFT macro
is used which is not defined anywhere in the kernel.
Until now the build was going through successfully, since it
is not being used anywhere in kernel.
This bug got introduced by the commit
358f0e630d ("OMAP3: hwmod: support
to specify the offset position of various SYSCONFIG register bits.")
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap_hwmod_softreset() does not seem to wait for reset status
after doing a softreset. Make it use _ocp_softreset() instead
which does this correctly.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After a softreset, make sure the sysc settings are correctly
restored.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
[paul@pwsan.com: combined post-reset SYSCONFIG reload code into the
_reset() function to avoid duplication and future mistakes]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some modules doesn't have SYSC_HAS_ENAWAKEUP bit available (ex: usb
host uhh module) in absence of this flag
omap_hwmod_enable/disable_wakeup avoids configuring pad mux wakeup
capability.
Configure sysc if SYSC_HAS_ENAWAKEUP is available and for other cases
try enabling/disabling wakeup from mux_pad pins.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[paul@pwsan.com: updated function kerneldoc documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Several clocks are missing clockdomains. This can cause problems with
the hwmod and power management code. Fill these in.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Matt Porter <mporter@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
All DPLLs except USB are in ALWON powerdomain. Make sure the
clkdm/pwrdm for USB DPLL (l3init) is turned on before attempting
a DPLL relock. So, mark the database accordingly.
Without this fix, it was seen that DPLL relock fails while testing
relock in a loop of USB DPLL.
Cc: Nishanth Menon <nm@ti.com>
Tested-by: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b1cbdb00d ("OMAP: clockdomain: Wait for powerdomain to be ON
when using clockdomain force wakeup") was assuming that
pwrdm_state_switch() does wait for the powerdomain transition which is
not the case. The missing wait for the powerdomain transition
violates the sequence which the hardware expects, which causes power
management failures on some devices.
Fix this API by adding the pwrdm_wait_transition().
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: added some more details in the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Because of the inclusion of skeleton.dtsi, the memory node is
named "memory" we where not modifying the already included one
but creating a new one. It caused bad memory node detection during
early_init_dt_scan_memory() so we modify them.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
SPI chip select pins have to be checked by gpio_is_valid().
The USB host overcurrent_pin checking was missing.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Change number of ports to 3 for newer SoCs. Modify pdata structure
and ohci-at91 code that was dealing with ports information and check
of port indexes.
Several coding style errors have been addresses as the patch was touching
affected lines of code and was producing errors while run through
checkpatch.pl.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Change vbus gpio configuration in .dts files to switch to
active low configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
Due to an error while handling vbus_pin_active_low in ohci-at91 driver,
the specification of this property was not good in devices/board files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org> [3.2+]
addruart cannot read from the physical address of the chipid
register, that will fail as soon as the mmu is turned on.
Fixing it to read from the physical or virtual address depending
on the mmu state also does not work, because there is a period
between head.S and exynos_map_io where the mmu is on, the uart
is mapped and used, but the chipid mapping is not yet present.
Fix addruart to use the ARM Main ID cp15 register to determine
if the core is Cortex A15 (EXYNOS5) or not (EXYNOS4).
Signed-off-by: Colin Cross <ccross@android.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rename EMAC clocks to match driver expectations: both davinci_emac and
davinci_mdio drivers call clk_get(dev, NULL) so we have to provide
("davinci_emac", NULL) and ("davinci_mdio.0", NULL) clocks instead of
("davinci_emac", "emac_clk") and ("davinci_emac", "phy_clk") resp.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Pull ARM fixes from Russell King:
"Nothing too big here, just small fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix more fallout from 9f97da78bf (Disintegrate asm/system.h for ARM)
ARM: fix bios32.c build warning
ARM: 7337/1: ptrace: fix ptrace_read_user for !CONFIG_MMU platforms
ARM: fix missing bug.h include in arch/arm/kernel/insn.c
ARM: sa11x0: fix build errors from DMA engine API updates
clk_disable_unused is invoked when CONFIG_OMAP_RESET_CLOCKS=y.
Since clk_disable_unused is called as lateinitcall, there can
be more than a few workqueues executing off secondary CPU(s).
The current code does the following:
a) checks if clk is unused
b) holds lock
c) disables clk
d) unlocks
Between (a) and (b) being executed on CPU0, It is possible to
have a driver executing on CPU1 which could do a get_sync->clk_get
(and increase the use_count) of the clock which was just about
to be disabled by clk_disable_unused.
We ensure instead that the entire list traversal is protected by
the lock allowing for parent child clock traversal which could be
potentially be done by runtime operations to be safe as well.
Reported-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
CLKS signal for McBSP ports can be selected from internal (PRCM) or
external (ABE_CLKS pin) source. To be able to use existing code we
need to create clock aliases consistent among OMAP2/3/4.
Based on a patch from Péter Ujfalusi <peter.ujfalusi@ti.com>;
the patch description above is his.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Commit 2a9f5a4d45 "OMAP3 clock: remove unnecessary duplicate of dpll4_m2_ck,
added for 36xx" consolidated dpll4 clock structures between 34xx and 36xx,
but left 34xx CLKSEL masks for most dpll4 related clocks, which causes
clock code to not behave correctly when booting on DM3730 with higher
(36xx only) divisors set:
[ 0.000000] WARNING: at arch/arm/mach-omap2/clkt_clksel.c:375 omap2_init_clksel_parent+0x104/0x114()
[ 0.000000] clock: dpll4_m3_ck: init parent: could not find regval 0
[ 0.000000] WARNING: at arch/arm/mach-omap2/clkt_clksel.c:194 omap2_clksel_recalc+0xd4/0xe4()
[ 0.000000] clock: Could not find fieldval 0 for clock dpll4_m3_ck parent dpll4_ck
Fix this by switching to 36xx masks, as valid divisors will be limited
by clksel_rate lists.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
If transceiver is attached to a MMC host of ES2.1 OMAP35xx, it seems
2.1.1.128 erratum doesn't apply and there is no data corruption,
probably because of different signal timing. The workaround for this
erratum disables multiblock reads, which causes dramatic loss of
performance (over 75% slower), so avoid it when transceiver is present.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
[paul@pwsan.com: edited commit message slightly]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 4430 ES2.0 TRM vX Table 3-744 "CM_EMU_CLKSTCTRL",
the emu_sys clockdomain data in mainline is incorrect.
The emu_sys clockdomain does not support the DISABLE_AUTO state, and
instead it supports the FORCE_WAKEUP state.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Fix the below section mismatch warning and alike:
WARNING: vmlinux.o(.text+0x281d4): Section mismatch in reference from
the function setup_ehci_io_mux() to the function
.init.text:omap_mux_init_signal()
The function setup_ehci_io_mux() references
the function __init omap_mux_init_signal().
This is often because setup_ehci_io_mux lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With CONFIG_OMAP4_ERRATA_I688 enabled, omap2+ build
was broken as below:
arch/arm/kernel/io.c: In function '_memcpy_toio':
arch/arm/kernel/io.c:29: error: implicit declaration of function 'outer_sync'
make[1]: *** [arch/arm/kernel/io.o] Error 1
This was caused by commit 9f97da78 (Disintegrate asm/system.h for ARM).
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize fixed regulators in the board files. Trying to
do this in a generic way in gpmc-smsc911x.c gets messy as
the regulator may be provided by drivers, such as twl4030,
for some boards.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: combined into one patch, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding in support for regulators here creates several headaches.
- Boards that declare their own regulator cannot use this function.
- Multiple calls to this function require special handling.
- Boards that declare id's other than '0' need special handling.
Now that there is a simple regulator_register_fixed, we can push
this registration back into the board files.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looking back into git history, this code was never used and was
probably left over from a copy/paste.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If this function is called the first time with flags set, and the
second time without flags set then the leftover flags from the first
called will be used rather than the desired default flags.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This seems to be a leftover from when gpmc-smsc911x.c was copied
from gpmc-smc91x.c.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 086ada54ab
"FB: sa1100: remove global sa1100fb_.*_power function pointers"
got rid of all instances but one in locomolcd.c -- which was
conditional on CONFIG_SA1100_COLLIE. The associated .power
field which replaces the global is populated in mach-sa1100/collie.c
so move the assignment there, but make it conditional on the
locomolcd support, so use CONFIG_BACKLIGHT_LOCOMO in that file.
Cc: arm@kernel.org
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
commit 9f786d033d
"arm/PCI: get rid of device resource fixups"
causes this failure on the versatile:
arch/arm/mach-versatile/pci.c: In function 'pci_versatile_setup_resources':
arch/arm/mach-versatile/pci.c:221: error: 'sys' undeclared (first use in this function)
because the versatile wasn't passing in the full struct pci_sys_data
but only the resource sub-field. Change it to pass in the full
struct so that sys will be in scope.
Reported-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This merges some of the fixes from Paul Gortmaker for the header file
cleanup fallout.
Some of the patches are going through arch maintainer trees, and David
Howells suggested another be done differently, but this at least fixes a
few cases.
* emailed from Paul Gortmaker <paul.gortmaker@windriver.com>:
asm-generic: add linux/types.h to cmpxchg.h
firewire: restore the device.h include in linux/firewire.h
frv: fix warnings in mb93090-mb00/pci-dma.c about implicit EXPORT_SYMBOL
parisc: fix missing cmpxchg file error from system.h split
blackfin: fix cmpxchg build fails from system.h fallout
avr32: fix build failures from mis-naming of atmel_nand.h
ARM: mach-msm: fix compile fail from system.h fallout
irq_work: fix compile failure on MIPS from system.h split
To fix:
In file included from arm/boot/compressed/misc.c:28:0:
arm/mach-msm/include/mach/uncompress.h: In function 'putc':
arch/arm/mach-msm/include/mach/uncompress.h:48:3: error: implicit
declaration of function 'smp_mb' [-Werror=implicit-function-declaration]
The putc does a cpu_relax which for this platform is smp_mb.
Bisect indicates the 1st failing commit as: 0195c00244 ("Merge tag
'split-asm_system_h...")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W59/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Pull cpumask cleanups from Rusty Russell:
"(Somehow forgot to send this out; it's been sitting in linux-next, and
if you don't want it, it can sit there another cycle)"
I'm a sucker for things that actually delete lines of code.
Fix up trivial conflict in arch/arm/kernel/kprobes.c, where Rusty fixed
a user of &cpu_online_map to be cpu_online_mask, but that code got
deleted by commit b21d55e98a ("ARM: 7332/1: extract out code patch
function from kprobes").
* tag 'for-linus' of git://github.com/rustyrussell/linux:
cpumask: remove old cpu_*_map.
documentation: remove references to cpu_*_map.
drivers/cpufreq/db8500-cpufreq: remove references to cpu_*_map.
remove references to cpu_*_map in arch/
Fix registration of camera clock so that mx3-camera driver can get its clock
correctly.
Reported-by: Alex Gershgorin <alexg@meprolight.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the following build warning:
arch/arm/mach-imx/mach-mx35_3ds.c: In function 'mx35_3ds_lcd_set_power':
arch/arm/mach-imx/mach-mx35_3ds.c:112: warning: passing argument 2 of 'gpiochip_find' from incompatible pointer type
include/asm-generic/gpio.h:145: note: expected 'int (*)(struct gpio_chip *, const void *)' but argument is of type 'int (*)(struct gpio_chip *, void *)'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes missing mach-s3c24xx/common.h which has been
lost when regarding s3c24xx directories merged.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
arch/arm/kernel/io.c: In function '_memcpy_toio':
arch/arm/kernel/io.c:29: error: implicit declaration of function 'outer_sync'
arch/arm/mach-omap2/omap_l3_noc.c: In function 'l3_interrupt_handler':
arch/arm/mach-omap2/omap_l3_noc.c💯 error: implicit declaration of function 'outer_sync'
kernel/irq/generic-chip.c: In function 'irq_gc_mask_disable_reg':
kernel/irq/generic-chip.c:45: error: implicit declaration of function 'outer_sync'
kernel/sched/rt.c: In function 'rt_set_overload':
kernel/sched/rt.c:248: error: implicit declaration of function 'outer_sync'
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull kbuild changes from Michal Marek:
- Unification of cmd_uimage among archs that use it
- make headers_check tries harder before reporting a missing
<linux/types.h> include
- kbuild portability fix for shells that do not support echo -e
- make clean descends into samples/
- setlocalversion grep fix
- modpost typo fix
- dtc warnings fix
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
setlocalversion: Use "grep -q" instead of piping output to "read dummy"
modpost: fix ALL_INIT_DATA_SECTIONS
Kbuild: centralize MKIMAGE and cmd_uimage definitions
headers_check: recursively search for linux/types.h inclusion
scripts/Kbuild.include: Fix portability problem of "echo -e"
scripts: dtc: fix compile warnings
kbuild: clean up samples directory
kbuild: disable -Wmissing-field-initializers for W=1
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
Two patches, one dealing with the system.h fallout, the other is a missing
linux/bug.h in a place where ARRAY_SIZE() is used.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=GQrl
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull a few more ARM platform fixes from Olof Johansson:
"Apologies for back-to-back fixes pull requests, but one of the patches
below are the kind we'll see posted over and over if we don't send it
in. I hadn't done the full sanity-check of defconfig builds by the
time I sent up the other fixes yesterday or I would have included it
then.
Two patches, one dealing with the system.h fallout, the other is a
missing linux/bug.h in a place where ARRAY_SIZE() is used."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: clps711x: fix missing include file
ARM: fix builds due to missing <asm/system_misc.h> includes
Pull ACPI & Power Management changes from Len Brown:
- ACPI 5.0 after-ripples, ACPICA/Linux divergence cleanup
- cpuidle evolving, more ARM use
- thermal sub-system evolving, ditto
- assorted other PM bits
Fix up conflicts in various cpuidle implementations due to ARM cpuidle
cleanups (ARM at91 self-refresh and cpu idle code rewritten into
"standby" in asm conflicting with the consolidation of cpuidle time
keeping), trivial SH include file context conflict and RCU tracing fixes
in generic code.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (77 commits)
ACPI throttling: fix endian bug in acpi_read_throttling_status()
Disable MCP limit exceeded messages from Intel IPS driver
ACPI video: Don't start video device until its associated input device has been allocated
ACPI video: Harden video bus adding.
ACPI: Add support for exposing BGRT data
ACPI: export acpi_kobj
ACPI: Fix logic for removing mappings in 'acpi_unmap'
CPER failed to handle generic error records with multiple sections
ACPI: Clean redundant codes in scan.c
ACPI: Fix unprotected smp_processor_id() in acpi_processor_cst_has_changed()
ACPI: consistently use should_use_kmap()
PNPACPI: Fix device ref leaking in acpi_pnp_match
ACPI: Fix use-after-free in acpi_map_lsapic
ACPI: processor_driver: add missing kfree
ACPI, APEI: Fix incorrect APEI register bit width check and usage
Update documentation for parameter *notrigger* in einj.txt
ACPI, APEI, EINJ, new parameter to control trigger action
ACPI, APEI, EINJ, limit the range of einj_param
ACPI, APEI, Fix ERST header length check
cpuidle: power_usage should be declared signed integer
...
linux/bug.h is needed due to an ARRAY_SIZE being used:
arch/arm/mach-clps711x/edb7211-mm.c: In function 'edb7211_map_io':
arch/arm/mach-clps711x/edb7211-mm.c:79:9: error: implicit declaration of function 'BUILD_BUG_ON_ZERO'
Signed-off-by: Olof Johansson <olof@lixom.net>
This does a sweeping change fixing up all the missing system_misc.h and
system_info.h includes from the system.h split-up change. These were the
ones I came across when building all defconfigs in arch/arm/configs, there
might be more but they lack adequate build coverage to be easily caught.
I'm expecting to get a lot of these piecemeal by each maintainer, so we
might just as well do one sweeping change to get them all at once.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
arch/arm/kernel/bios32.c: In function 'pcibios_fixup_bus':
arch/arm/kernel/bios32.c:302: warning: unused variable 'root'
caused by 9f786d033 (arm/PCI: get rid of device resource fixups)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 68b7f715 ("nommu: ptrace support") added definitions for
PT_TEXT_ADDR and friends, as well as adding ptrace support for reading
from these magic offsets.
Unfortunately, this has probably never worked, since ptrace_read_user
predicates reading on off < sizeof(struct user), returning -EIO
otherwise.
This patch moves the offset size check until after we have tried to
match it against either a magic value or an offset into pt_regs.
Cc: Paul Brook <paul@codesourcery.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/kernel/insn.c: In function '__arm_gen_branch_thumb2':
arch/arm/kernel/insn.c:13: error: implicit declaration of function 'WARN_ON_ONCE'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a first pass of some of the merge window fallout for ARM platforms.
Nothing controversial:
* A system.h fallout fix for OMAP
* PXA fixes for breakage caused by the regulator struct changes
* GPIO fixes for OMAP to properly deal with dynamic IRQ allocation
* A mismerge in our arm-soc tree of an lpc32xx change for networking
* A fix for USB setup on tegra
* An undo of __init annotation of display mux setup on OMAP that's needed
at runtime
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=36Eb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Olof Johansson:
"This is a first pass of some of the merge window fallout for ARM
platforms.
Nothing controversial:
- A system.h fallout fix for OMAP
- PXA fixes for breakage caused by the regulator struct changes
- GPIO fixes for OMAP to properly deal with dynamic IRQ allocation
- A mismerge in our arm-soc tree of an lpc32xx change for networking
- A fix for USB setup on tegra
- An undo of __init annotation of display mux setup on OMAP that's
needed at runtime"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix build issue on stargate2
ARM: pxa: fix build issue on cm-x300
ARM: pxa: fix build failure for regulator consumer in em-x270.c
ARM: LPC32xx: clock.c: Fix lpc-eth clock reference
ARM: OMAP: pm: fix compilation break
ARM: OMAP: Remove OMAP_GPIO_IRQ macro definition
drivers: input: Fix OMAP_GPIO_IRQ with gpio_to_irq() in ams_delta_serio_exit()
ARM: OMAP: boards: Fix OMAP_GPIO_IRQ usage with gpio_to_irq()
ARM: pxa: fix regulator related build fail in magician_defconfig
ARM: tegra: Fix device tree AUXDATA for USB/EHCI
ARM: OMAP2+: Remove __init from DSI mux functions
Pull x32 support for x86-64 from Ingo Molnar:
"This tree introduces the X32 binary format and execution mode for x86:
32-bit data space binaries using 64-bit instructions and 64-bit kernel
syscalls.
This allows applications whose working set fits into a 32 bits address
space to make use of 64-bit instructions while using a 32-bit address
space with shorter pointers, more compressed data structures, etc."
Fix up trivial context conflicts in arch/x86/{Kconfig,vdso/vma.c}
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
x32: Fix alignment fail in struct compat_siginfo
x32: Fix stupid ia32/x32 inversion in the siginfo format
x32: Add ptrace for x32
x32: Switch to a 64-bit clock_t
x32: Provide separate is_ia32_task() and is_x32_task() predicates
x86, mtrr: Use explicit sizing and padding for the 64-bit ioctls
x86/x32: Fix the binutils auto-detect
x32: Warn and disable rather than error if binutils too old
x32: Only clear TIF_X32 flag once
x32: Make sure TS_COMPAT is cleared for x32 tasks
fs: Remove missed ->fds_bits from cessation use of fd_set structs internally
fs: Fix close_on_exec pointer in alloc_fdtable
x32: Drop non-__vdso weak symbols from the x32 VDSO
x32: Fix coding style violations in the x32 VDSO code
x32: Add x32 VDSO support
x32: Allow x32 to be configured
x32: If configured, add x32 system calls to system call tables
x32: Handle process creation
x32: Signal-related system calls
x86: Add #ifdef CONFIG_COMPAT to <asm/sys_ia32.h>
...
arch/arm/mach-pxa/stargate2.c:155:3: error: unknown field ‘dev’
specified in initializer
arch/arm/mach-pxa/stargate2.c:155:3: warning: initialization from
incompatible pointer type [enabled by default]
arch/arm/mach-pxa/stargate2.c:155:3: warning: (near initialization for
‘stargate2_sensor_3_con[0].dev_name’) [enabled by default]
make[1]: *** [arch/arm/mach-pxa/stargate2.o] Error 1
make: *** [arch/arm/mach-pxa] Error 2
It's caused by 'dev' field removed from struct
regulator_consumer_supply.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
Commit 737f360d5b
"regulator: Remove support for supplies specified by struct device"
caused this file to break, since it was still relying on the
device field to be present. Map it onto dev_name appropriately
Since there are two consumers with the name "reg-userspace-consumer",
we have to supply the ID as a suffix in the REGULATOR_CONSUMER calls.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
From Tony Lindgren:
"This contains the updated gpio_to_irq patches from Tarun, and a trivial
build fix from Govindraj to #include <asm/system_misc.h> in pm.c.
The DSI mux patch is the same."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: pm: fix compilation break
ARM: OMAP: Remove OMAP_GPIO_IRQ macro definition
drivers: input: Fix OMAP_GPIO_IRQ with gpio_to_irq() in ams_delta_serio_exit()
ARM: OMAP: boards: Fix OMAP_GPIO_IRQ usage with gpio_to_irq()
ARM: OMAP2+: Remove __init from DSI mux functions
* 'for-3.4/fixes-for-rc1-and-v3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: Fix device tree AUXDATA for USB/EHCI
During a complex merge for v3.4, one line of the commit
c20b909be9 ("ARM: LPC32xx: Ethernet support") was
reverted wrongly ("lpc-eth.0" -> "lpc-net.0") while the other conflicts were
merged correctly. This patch re-applies the clock name "lpc-eth.0".
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
