Similar to ieee80211_get_sband but get the sband of the link_conf.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AP SMPS was removed and not needed anymore. Remove the leftovers.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Management frames are transmitted from link address and not device
address. Allow that.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check all the MLO links to decide whether offchannel TX is needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When checking whether or not to accept a frame in RX,
take into account the configured link addresses. Also
look up the link station correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211s_update_metric function uses sta_set_rate_info_tx
function to get struct rate_info data from ieee80211_tx_rate
struct, present in ieee80211_sta->deflink.tx_stats. However,
drivers can skip tx rate calculation by setting rate idx as
-1. Such drivers provides rate_info directly and hence
ieee80211s metric is updated incorrectly since ieee80211_tx_rate
has inconsistent data.
Add fix to use rate_info directly if present instead of
sta_set_rate_info_tx for updating ieee80211s metric.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://lore.kernel.org/r/20220701133611.544-1-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WDS needs 4addr packets to trigger AP for wlan0.sta creation.
However, the 4addr null frame is sent at a high rate so that
sometimes the AP can't receive it. Switch to using min rate.
Signed-off-by: Lian Chen <lian.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220714091636.59107-1-lian.chen@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, multicast traffic is handled very differently from normal traffic,
especially if at least one client is in powersave mode.
This means that multicast packets can be buffered a lot longer than normal
unicast packets, and can eat up the AQL budget very quickly because of the low
data rate.
Along with the recent change to maintain a global PHY AQL limit, this can lead
to significant latency spikes for unicast traffic.
Since queueing multicast to hardware is currently not constrained by AQL limits
anyway, let's just exclude it from the AQL pending airtime calculation entirely.
Fixes: 8e4bac0671 ("wifi: mac80211: add a per-PHY AQL limit to improve fairness")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220713083444.86129-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return directly without intermediate value store at the end of
devlink_port_new_notify() function.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the typo in a name of devlink_port_new_notifiy() function.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return value is not used, so change the return value type to void.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a nexthop is added, without a gw address, the default scope was set
to 'host'. Thus, when a source address is selected, 127.0.0.1 may be chosen
but rejected when the route is used.
When using a route without a nexthop id, the scope can be configured in the
route, thus the problem doesn't exist.
To explain more deeply: when a user creates a nexthop, it cannot specify
the scope. To create it, the function nh_create_ipv4() calls fib_check_nh()
with scope set to 0. fib_check_nh() calls fib_check_nh_nongw() wich was
setting scope to 'host'. Then, nh_create_ipv4() calls
fib_info_update_nhc_saddr() with scope set to 'host'. The src addr is
chosen before the route is inserted.
When a 'standard' route (ie without a reference to a nexthop) is added,
fib_create_info() calls fib_info_update_nhc_saddr() with the scope set by
the user. iproute2 set the scope to 'link' by default.
Here is a way to reproduce the problem:
ip netns add foo
ip -n foo link set lo up
ip netns add bar
ip -n bar link set lo up
sleep 1
ip -n foo link add name eth0 type dummy
ip -n foo link set eth0 up
ip -n foo address add 192.168.0.1/24 dev eth0
ip -n foo link add name veth0 type veth peer name veth1 netns bar
ip -n foo link set veth0 up
ip -n bar link set veth1 up
ip -n bar address add 192.168.1.1/32 dev veth1
ip -n bar route add default dev veth1
ip -n foo nexthop add id 1 dev veth0
ip -n foo route add 192.168.1.1 nhid 1
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> RTNETLINK answers: Invalid argument
> $ ip netns exec foo ping -c1 192.168.1.1
> ping: connect: Invalid argument
Try without nexthop group (iproute2 sets scope to 'link' by dflt):
ip -n foo route del 192.168.1.1
ip -n foo route add 192.168.1.1 dev veth0
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> 192.168.1.1 dev veth0 src 192.168.0.1 uid 0
> cache
> $ ip netns exec foo ping -c1 192.168.1.1
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.039 ms
>
> --- 192.168.1.1 ping statistics ---
> 1 packets transmitted, 1 received, 0% packet loss, time 0ms
> rtt min/avg/max/mdev = 0.039/0.039/0.039/0.000 ms
CC: stable@vger.kernel.org
Fixes: 597cfe4fc3 ("nexthop: Add support for IPv4 nexthops")
Reported-by: Edwin Brossette <edwin.brossette@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220713114853.29406-1-nicolas.dichtel@6wind.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Both helper functions bpf_lwt_seg6_action() and bpf_lwt_push_encap() use
the bpf_push_seg6_encap() to encapsulate the packet in an IPv6 with Segment
Routing Header (SRH) or insert an SRH between the IPv6 header and the
payload.
To achieve this result, such helper functions rely on bpf_push_seg6_encap()
which, in turn, leverages seg6_do_srh_{encap,inline}() to perform the
required operation (i.e. encap/inline).
This patch removes the initialization of the IPv6 header payload length
from bpf_push_seg6_encap(), as it is now handled properly by
seg6_do_srh_{encap,inline}() to prevent corruption of the skb checksum.
Fixes: fe94cc290f ("bpf: Add IPv6 Segment Routing helpers")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The SRv6 End.B6 and End.B6.Encaps behaviors rely on functions
seg6_do_srh_{encap,inline}() to, respectively: i) encapsulate the
packet within an outer IPv6 header with the specified Segment Routing
Header (SRH); ii) insert the specified SRH directly after the IPv6
header of the packet.
This patch removes the initialization of the IPv6 header payload length
from the input_action_end_b6{_encap}() functions, as it is now handled
properly by seg6_do_srh_{encap,inline}() to avoid corruption of the skb
checksum.
Fixes: 140f04c33b ("ipv6: sr: implement several seg6local actions")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Support for SRH encapsulation and insertion was introduced with
commit 6c8702c60b ("ipv6: sr: add support for SRH encapsulation and
injection with lwtunnels"), through the seg6_do_srh_encap() and
seg6_do_srh_inline() functions, respectively.
The former encapsulates the packet in an outer IPv6 header along with
the SRH, while the latter inserts the SRH between the IPv6 header and
the payload. Then, the headers are initialized/updated according to the
operating mode (i.e., encap/inline).
Finally, the skb checksum is calculated to reflect the changes applied
to the headers.
The IPv6 payload length ('payload_len') is not initialized
within seg6_do_srh_{inline,encap}() but is deferred in seg6_do_srh(), i.e.
the caller of seg6_do_srh_{inline,encap}().
However, this operation invalidates the skb checksum, since the
'payload_len' is updated only after the checksum is evaluated.
To solve this issue, the initialization of the IPv6 payload length is
moved from seg6_do_srh() directly into the seg6_do_srh_{inline,encap}()
functions and before the skb checksum update takes place.
Fixes: 6c8702c60b ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/all/20220705190727.69d532417be7438b15404ee1@uniroma2.it
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Return value of unregister_tcf_proto_ops is unused, remove it.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath10k
* ethernet frame format support
rtw89
* TDLS support
cfg80211/mac80211
* airtime fairness fixes
* EHT support continued, especially in AP mode
* initial (and still major) rework for multi-link
operation (MLO) from 802.11be/wifi 7
As usual, also many small updates/cleanups/fixes/etc.
-----BEGIN PGP SIGNATURE-----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=smwk
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
A fairly large set of updates for next, highlights:
ath10k
* ethernet frame format support
rtw89
* TDLS support
cfg80211/mac80211
* airtime fairness fixes
* EHT support continued, especially in AP mode
* initial (and still major) rework for multi-link
operation (MLO) from 802.11be/wifi 7
As usual, also many small updates/cleanups/fixes/etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* queue selection in mesh/ocb
* queue handling on interface stop
* hwsim virtio device vs. some other virtio changes
* dt-bindings email addresses
* color collision memory allocation
* a const variable in rtw88
* shared SKB transmit in the ethernet format path
* P2P client port authorization
-----BEGIN PGP SIGNATURE-----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=GrDi
-----END PGP SIGNATURE-----
Merge tag 'wireless-2022-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
A small set of fixes for
* queue selection in mesh/ocb
* queue handling on interface stop
* hwsim virtio device vs. some other virtio changes
* dt-bindings email addresses
* color collision memory allocation
* a const variable in rtw88
* shared SKB transmit in the ethernet format path
* P2P client port authorization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 multicast routing code previously implemented only the dump
variant of RTM_GETROUTE. Implement single MFC item retrieval by copying
and adapting the respective IPv4 code.
Tested against FRRouting's IPv6 PIM stack.
Signed-off-by: David Lamparter <equinox@diac24.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As far as the lock helpers exist as the drivers need to work with the
devlink->lock mutex, use the helpers internally in devlink.c in order to
be consistent.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be unified with the rest of the code, the unlocked version (devl_*)
of function should have the same description in documentation as the
locked one. Add the missing documentation. Also, add "Context"
annotation for the locked versions where it is missing.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading nexthop_compat_mode, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 4f80116d3d ("net: ipv4: add sysctl for nexthop api compatibility mode")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_dynaddr, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_ecn_fallback, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 492135557d ("tcp: add rfc3168, section 6.1.1.1. fallback")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_ecn, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_icmp_ratemask, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_icmp_ratelimit, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_icmp_errors_use_inbound_ifaddr, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 1c2fb7f93c ("[IPV4]: Sysctl configurable icmp error source address.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_icmp_ignore_bogus_error_responses, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_icmp_echo_ignore_broadcasts, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_icmp_echo_enable_probe, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: d329ea5bd8 ("icmp: add response to RFC 8335 PROBE messages")
Fixes: 1fd07f33c3 ("ipv6: ICMPV6: add response to ICMPV6 RFC 8335 PROBE messages")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_icmp_echo_ignore_all, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_max_tw_buckets, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So it can be used for port range filter offloading.
Co-developed-by: Volodymyr Mytnyk <volodymyr.mytnyk@plvision.eu>
Signed-off-by: Volodymyr Mytnyk <volodymyr.mytnyk@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code allows to inherit the TTL (hop_limit) from the
payload when skb->protocol is ETH_P_IP or ETH_P_IPV6.
However when the payload is VLAN encapsulated (e.g because the tunnel
is of type GRETAP), then this inheriting does not work, because the
visible skb->protocol is of type ETH_P_8021Q or ETH_P_8021AD.
Instead of skb->protocol, use skb_protocol().
Signed-off-by: Matthias May <matthias.may@westermo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the payload is a VLAN encapsulated IPv6/IPv6 frame, we can
skip the 802.1q/802.1ad ethertypes and jump to the actual protocol.
This way we treat IPv4/IPv6 frames as IP instead of as "other".
Signed-off-by: Matthias May <matthias.may@westermo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code always forces a dscp of 0 for all non-IP frames.
However when setting a specific TOS with the command
ip link add name tep0 type ip6gretap local fdd1:ced0:5d88:3fce::1
remote fdd1:ced0:5d88:3fce::2 tos 0xa0
one would expect all GRE encapsulated frames to have a TOS of 0xA0.
and not only when the payload is IPv4/IPv6.
Signed-off-by: Matthias May <matthias.may@westermo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code allows to inherit the TOS, TTL, DF from the payload
when skb->protocol is ETH_P_IP or ETH_P_IPV6.
However when the payload is VLAN encapsulated (e.g because the tunnel
is of type GRETAP), then this inheriting does not work, because the
visible skb->protocol is of type ETH_P_8021Q or ETH_P_8021AD.
Instead of skb->protocol, use skb_protocol().
Signed-off-by: Matthias May <matthias.may@westermo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the id accounting for the ID 0 subflow is not correct:
at creation time we mark (correctly) as unavailable the endpoint
id corresponding the MPC subflow source address, while at subflow
removal time set as available the id 0.
With this change we track explicitly the endpoint id corresponding
to the MPC subflow so that we can mark it as available at removal time.
Additionally this allow deleting the initial subflow via the NL PM
specifying the corresponding endpoint id.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Any local endpoints configured on the address matching the
MPC subflow are currently ignored.
Specifically, setting a backup flag on them has no effect
on the first subflow, as the MPC handshake can't carry such
info.
This change refactors the MPC endpoint id accounting to
additionally fetch the priority info from the relevant endpoint
and eventually trigger the MP_PRIO handshake as needed.
As a result, the MPC subflow now switches to backup priority
after that the MPTCP socket is fully established, according
to the local endpoint configuration.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When looking-up a socket address in the endpoint list, we
must prefer port-based matches over address only match.
Ensure that port-based endpoints are listed first, using
head insertion for them. Additionally be sure that only
port-based endpoints carry a non zero port number.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The in-kernel PM has a bit of duplicate code related to ack
generation. Create a new helper factoring out the PM-specific
needs and use it in a couple of places.
As a bonus, mptcp_subflow_send_ack() is not used anymore
outside its own compilation unit and can become static.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Let the core take the devlink instance lock around port_new and port_del
callbacks and remove the now redundant locking in the only driver that
currently use them.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
