HEVC is a video coding format
Signed-off-by: Smitha T Murthy <smitha.t@samsung.com>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of switching capture mode depending on how many buffers are
available use a scratch buffer and always run in continuous mode. By
using a scratch buffer the responsiveness of the capture loop is
increased as it can keep running even if there are no buffers available
from userspace.
As soon as a userspace queues a buffer it is inserted into the capture
loop and returned as soon as it is filled. This is a improvement on the
previous logic where the whole capture loop was stopped and switched to
single capture mode if userspace did not feed the VIN driver buffers at
the same time it consumed them. To make matters worse it was difficult
for the driver to reenter continuous mode if it entered single mode even
if userspace started to queue buffers faster. This resulted in
suboptimal performance where if userspace where delayed for a short
period the ongoing capture would be slowed down and run in single mode
until the capturing process where restarted.
An additional effect of this change is that the capture logic can be
made much simple as we know that continuous mode will always be used.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Before starting a capture, allocate a scratch buffer which can be used
by the driver to give to the hardware if no buffers are available from
userspace. The buffer is not used in this patch but prepares for future
refactoring where the scratch buffer can be used to avoid the need to
fallback on single capture mode if userspace can't queue buffers as fast
as the VIN driver consumes them.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The newly added pdev variable is only used in an #ifdef, causing a
build warning without CONFIG_PCI_MSI, unless we move the declaration
inside the same #ifdef:
drivers/media/pci/ngene/ngene-core.c: In function 'ngene_start':
drivers/media/pci/ngene/ngene-core.c:1328:17: error: unused variable 'pdev' [-Werror=unused-variable]
Fixes: 6795bf6264 ("media: ngene: convert kernellog printing from printk() to dev_*() macros")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We now get a warning after the 'dmadev' variable is no longer used:
drivers/media/platform/omap/omap_vout_vrfb.c: In function 'omap_vout_prepare_vrfb':
drivers/media/platform/omap/omap_vout_vrfb.c:239:21: error: unused variable 'dmadev' [-Werror=unused-variable]
Fixes: 8f0aa38292 ("media: v4l: omap_vout: vrfb: Use the wrapper for prep_interleaved_dma()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When loading the budget_av driver for ie. a KNC1 DVB-C TDA10024 card,
which makes use of the ttpci eeprom check functionality (that always
fails on these cards, but that's no issue at all), this is printed
to the kernel log:
[ 10.497333] saa7146 (0): dma buffer size 192512
[ 10.497335] dvbdev: DVB: registering new adapter (KNC1 DVB-C TDA10024)
[ 10.545007] adapter failed MAC signature check
[ 10.545009] encoded MAC from EEPROM was
[ 10.545010] ff:
[ 10.545011] ff:
[ 10.545011] ff:
...
[ 10.545021] ff
[ 10.832422] budget_av: KNC1-4: MAC addr = 00:09:d6:6d:b3:be
with the 'ff' being repeated for a total of 20 times. Improve that by
using the %*phC format specifier instead dprintk()'ing every byte of the
encoded MAC separately. This obsoletes the int i, and the kernel log
looks cleaner:
[ 3234.383153] saa7146 (0): dma buffer size 192512
[ 3234.383154] dvbdev: DVB: registering new adapter (KNC1 DVB-C TDA10024)
[ 3234.428745] adapter failed MAC signature check
[ 3234.428747] encoded MAC from EEPROM was ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff
[ 3234.728194] budget_av: KNC1-0: MAC addr = 00:09:d6:6d:b3:be
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove soc_camera framework dependencies from mt9t112 sensor driver.
- Handle clk, gpios and power routines
- Register async subdev
- Remove deprecated g/s_mbus_config operations
- Remove driver flags
- Change driver interface and add kernel doc
- Adjust build system
- Fix code style issues reported by checkpatch in strict mode
This commit does not remove the original soc_camera based driver as long
as other platforms depends on soc_camera framework.
As I don't have access to a working camera module, this change has only
been compile tested.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Copy the soc_camera based driver in v4l2 sensor driver directory.
This commit just copies the original file without modifying it.
No modification to KConfig and Makefile as soc_camera framework
dependencies need to be removed first in next commit.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add probe and disconnect callbacks that behaves similarly than ones
used commonly on Linux driver model. We need those to get early / late
access to driver in order to use normal probe time stuff, like regmap,
extra bus adapters and so.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace static stream settings by one which enables and disables
stream interface when needed (TS streaming control).
1) Configure both TS IF and USB endpoints according to current use case
2) Disable streaming USB endpoints when streaming is stopped and
enable when streaming is started. Reduces sleep power consumption
slightly.
3) Reduce USB buffersize slightly, from 130848 to 98136 bytes
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
PID filters are moved to af9013 demod driver as those are property of
demod. As pid filters are now implemented correctly by demod driver,
we could enable pid filter support for possible slave demod too on
dual tuner configuration.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
af9013 demod has pid filter. Add support for it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
No one is binding that driver through media attach so remove it and
all related dead code.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
af9013 demod driver has i2c binding. Use it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert inttabs to format (reg, mask, val) which are suitable
parameters to pass directly for regmap_update_bits.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pass correct device to dev_* logging functions, which allows us to
remove redundant KBUILD_MODNAME and __func__ parameters from log format.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver has calculated dvbv5 statistics, so use those as a base for
legacy dvbv3 statistics. Wrap and convert needed values to dvbv3,
remove old dvbv3 statistic implementations.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement dvbv5 signal strength estimate. We know tuner dependent
-80dBm and -50dBm agc values, construct line equation and use it to
map agc value to signal strength estimate.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Whilst rewritten largely, the basic logic remains same with one
exception: do not return immediately on success case. We are going to
add statistics that function and cannot return too early.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This mceusb does not need the carrier count quirk, with it set it reports
the carrier higher than it is.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Windows Media Center IR transceivers include two IR receivers;
wide-band/short-range and narrow-band/long-range. The short-range
(5cm distance) receiver is for IR learning and has IR carrier
frequency measuring ability.
Add mceusb driver support to select the short range IR receiver
and enable pass through of its IR carrier frequency measurements.
RC and LIRC already support these mceusb driver additions.
Test platform:
Linux raspberrypi 4.9.59-v7+ #1047 SMP Sun Oct 29 12:19:23 GMT 2017 armv7l GNU/Linux
mceusb 1-1.2:1.0: Registered Pinnacle Systems PCTV Remote USB with mce emulator interface version 1
mceusb 1-1.2:1.0: 2 tx ports (0x0 cabled) and 2 rx sensors (0x1 active)
Sony TV remote control
ir-ctl from v4l-utils
pi@raspberrypi:~ $ ir-ctl -V
IR raw version 1.12.3
pi@raspberrypi:~ $ ir-ctl -m -r
...
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 1200
space 600
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 550
carrier 40004
space 16777215
^C
pi@raspberrypi:~ $ exit
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A timeout of 200ms is much longer than necessary, and delays the decoding
decoding of a single scancode and the last scancode when a button is being
held. This makes the remote seem sluggish.
If the min_timeout and max_timeout values are set, the timeout is
configurable via the LIRC_SET_REC_TIMEOUT ioctl.
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Meson doesn't seem to be able to generate timeout events in hardware. So
install a software timer to generate the timeout events required by the
decoders to prevent "ghost keypresses".
Reported-by: Matthias Reichl <hias@horus.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop bogus call to usb_driver_release_interface() from the disconnect()
callback. As the interface is already being unbound at this point,
usb_driver_release_interface() simply returns early.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV7604 has thirteen 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
[Kieran: Re-adapted for mainline]
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has twelve 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has 12 pages mapped onto I2C addresses.
In the existing implementation only 11 are mapped correctly in the page
enumerations, which causes an off-by-one fault on pages above the
infoframe definition due to a missing 'CBUS' page.
This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly
programmed during the iterations in adv748x_initialise_clients().
Until now this has gone un-noticed due to the fact that following the
creation of the clients - the device is reset and the addresses are
reprogrammed in manually by the call to "adv748x_write_regs(state,
adv748x_set_slave_address);"
As part of moving to dynamic i2c address allocations repair this by
providing the missing CBUS page definition.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has identical map configurations for each register map. The
duplication of each map can be simplified using a helper macro such that
each map is represented on a single line.
Define ADV748X_REGMAP_CONF for this purpose use it to create the tables.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_subdev core s_power op was used for two different things: power on/off
sensors or video decoders/encoders and to put a tuner in standby (and only the
tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner
is accessed.
The danger with calling (s_power, 0) to put a tuner into standby is that it is
usually broadcast for all subdevs. So a video receiver subdev that supports
s_power will also be powered off, and since there is no corresponding (s_power, 1)
they will never be powered on again.
In addition, this is specifically meant for tuners only since they draw the most
current.
This patch adds a new tuner op called 'standby' and replaces all calls to
(core, s_power, 0) by (tuner, standby). This prevents confusion between the two
uses of s_power. Note that there is no overlap: bridge drivers either just want
to put the tuner into standby, or they deal with powering on/off sensors. Never
both.
This also makes it easier to replace s_power for the remaining bridge drivers
with some PM code later.
Whether we want something cleaner for tuners in the future is a separate topic.
There is a lot of legacy code surrounding tuners, and I am very hesitant about
making changes there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed si470x_start() disabling the interrupt signal, causing tune
operations to never complete. This does not affect USB radios
because they poll the registers instead of using the IRQ line.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
[hans.verkuil@cisco.com: fixed 80 column checkpatch warning]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Added the call to v4l2_device_register() required to add a new radio device.
Without this patch, it is impossible for the driver to load. This does not
affect USB devices.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed si470x_set_channel() trying to tune before chip is turned
on, which causes warnings in dmesg and when probing, makes driver
wait for 3s for tuning timeout. This issue did not affect USB
devices because they have a different probing sequence.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
[hans.verkuil@cisco.com: fixed space-after-( checkpatch warning]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do not stop/restart dma on overrun or errors.
Dma will be restarted on current frame transfer
completion. Frame transfer completion is ensured
even if overrun or error occurs by DCMI continuous
capture mode which restarts data transfer at next
frame sync.
Do no warn on overrun while in irq thread, this slows down
system and lead to more overrun errors. Use a counter
instead and log errors at stop streaming.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_find_nearest_format is not useful for drivers in finding the best
matching format as it assumes a V4L2 specific struct. Drivers will use
v4l2_find_nearest_size instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a function (as well as a helper macro) to obtain the best size in a
list of device specific sizes. This helps writing drivers as well as
aligns interface behaviour across drivers.
The struct in which this information is contained in is typically specific
to the driver, therefore the existing function v4l2_find_nearest_format()
does not address the need.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This renames the protocol for the imon rc driver from other to imon,
since it is now an known protocol. Although different name will show up
in the sysfs protocol file, loading a keymap using existing ir-keytable
versions still works.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes it possible to use the various iMON remotes with any raw IR
RC device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If there is IR in the raw kfifo when ir_raw_event_unregister() is called,
then kthread_stop() causes ir_raw_event_thread to be scheduled, decode
some scancodes and re-arm timer_keyup. The timer_keyup then fires when
the rc device is long gone.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These devices were supported by the lirc_imon.c driver which was removed
from staging in commit f41003a23a ("[media] staging: lirc_imon: port
remaining usb ids to imon and remove").
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Note that the stick on the remote is not supported yet.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This code was ported without the necessary hardware to test. There
are multiple problems which are more easily solved by writing a
separate driver.
This reverts commit f41003a23a.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch updates the sunxi-ir driver to set the base clock frequency from
devicetree.
This is necessary since there are different ir receivers on the
market, that operate with different frequencies. So this value could be
set if the attached ir receiver needs a different base clock frequency,
than the default 8 MHz.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a double sizeof() typo here so we don't duplicate the struct
properly.
Fixes: be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Like in ddbridge, get rid of all duplicated I2C client handling constructs
and rather make use of the newly added dvb_module_*() helpers. Makes
things more clean and removes the (cosmetic) need for some variables.
The check on a valid ptr on ci->en isn't really needed since the cxd2099
driver will set it at a time where it is going to return successfully
from probing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of keeping duplicated I2C client handling construct, make use of
the newly introduced dvb_module_*() helpers. This not only keeps things
way cleaner and removes the need for duplicated I2C client attach code,
but even allows to get rid of some variables that won't help in making
things look cleaner anymore.
The check on a valid ptr on port->en isn't really needed since the cxd2099
driver will set it at a time where it is going to return successfully
from probing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CIMaX SP2 driver is a EN50221 CI controller I2C driver similar to the
cxd2099 driver. Move it's Kconfig block into the newly introduced CI
subsection.
Cc: Olli Salonen <olli.salonen@iki.fi>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cxd2099 driver makes use of the Regmap I2C kernel API, thus add
"select REGMAP_I2C" to it's Kconfig block. Also, make it default "m" if
!MEDIA_SUBDRV_AUTOSELECT, just like every other dvb-frontend driver.
And, while at it, remove the hyphens around the help tag.
Cc: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If I2C is present and it is module, the DVB core should also
be a module, otherwise build will now fail with:
drivers/media/dvb-core/dvbdev.o: In function `dvb_module_probe':
drivers/media/dvb-core/dvbdev.c:965: undefined reference to `i2c_new_device'
drivers/media/dvb-core/dvbdev.c:972: undefined reference to `i2c_unregister_device'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's a comment there at s82168 that it is wrong.
With firmware 4.0.11, sleep/resume works well without
need of download it every time. But firmware 4.0.19
needs to be downloaded again after sleep.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:268 s5c73m3_check_status() error: uninitialized symbol 'status'.
if s5c73m3_check_status() is called too late, time_is_after_jiffies(end)
will return 0, causing the while to abort before reading status.
The current code will do the wrong thing here, as it will still
check if status != value. The right fix here is to change
the logic to ensure that it will always read the status.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c: In function ‘cxd2880_set_ber_per_period_t’:
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c:677:34: warning: variable ‘c’ set but not used [-Wunused-but-set-variable]
struct dtv_frontend_properties *c;
^
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c: In function ‘cxd2880_set_ber_per_period_t2’:
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c:790:34: warning: variable ‘c’ set but not used [-Wunused-but-set-variable]
struct dtv_frontend_properties *c;
^
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c: In function ‘cxd2880_get_frontend’:
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c:1799:23: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
struct cxd2880_priv *priv = NULL;
^~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is not needed anymore to include the dvb-core directory,
as all the public headers that used to be there was moved
to include/media.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the Makefile, Kconfig files of driver
and MAINTAINERS file update about the driver
for the Sony CXD2880 DVB-T2/T tuner + demodulator.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These functions monitor the driver and watch for task completion.
This is part of the Sony CXD2880 DVB-T2/T tuner + demodulator driver.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This part of the driver has the main routines to handle
the tuner and demodulator functionality. The tnrdmd_mon.* files
have monitor functions for the driver.
This is part of the Sony CXD2880 DVB-T2/T tuner + demodulator driver.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These are common files for the driver for the
Sony CXD2880 DVB-T2/T tuner + demodulator.
These contains helper functions for the driver.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the SPI adapter part of the driver for the
Sony CXD2880 DVB-T2/T tuner + demodulator.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Not sure why, but, on ia64, with Linaro's gcc 7.3 compiler,
using #ifdef (CONFIG_I2C) is not OK.
So, replace it by IS_ENABLED(CONFIG_I2C), in order to fix the
builds there.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge produced a revision of ImpactVCBe using an 888,
with a 25MHz crystal, instead of using the default third
overtone 50Mhz crystal. This overrides that frequency so
that the cx25840 is properly configured. Without the proper
crystal setup the cx25840 cannot load the firmware or
decode video.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently clk_freq is ignored entirely, because the cx235840 driver
configures the xtal at the chip defaults. This is an issue if a
board is produced with a non-default frequency crystal. If clk_freq
is not zero the cx25840 will attempt to use the setting provided,
or fall back to defaults otherwise.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Proper cx2388x chip type is detected in cx25840 probe, the clock
rate is untouched however in probe. The cx25840 only checks for
non default clock values for 888 and provides custom settings for
25MHz 888. This change ensures that cx23888 chips with default 50MHz
crystals will not get configured as if they have 25MHz crystals. A
cx23887 board will continue to be configured for 25MHz crystal as
there is no custom clock support included for it.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cx25840 driver currently configures 885, 887, and 888 using
default divisors for each chip. This check to see if the cx23885
driver has passed the cx25840 a non-default clock rate for a
specific chip. If a cx23885 board has left clk_freq at 0, the
clock default values will be used to configure the PLLs.
This patch only has effect on 888 boards who set clk_freq to 25M.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The GPIO settings for quadHD boards are wrong. Fix them.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge HVR-975 is a hybrid, dual frontend, single tuner USB device.
It contains lgdt3306a and si2168 frontends and one si2157 tuner. The
lgdt3306a frontend is currently enabled. This creates the second
demodulator and attaches it to the tuner.
Enables lgdt3306a|si2168 + si2157
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If frontend[1] exists, then enable the dvb adapter mfe lock system.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Utilize the i2c mux adapter returned by the frontend.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This symbol mismatch is handled by NULL'ing out the release
callback if the driver is loaded as an i2c device.
This patch reverts:
- commit 94448e21cf ("media: lgdt3306a: Fix a double kfree on i2c
device remove")
- commit 835d66173a ("media: lgdt3306a: Fix module count mismatch
on usb unplug")
The symbol count mismatch is handled by:
- commit 5b3a8e9069 ("media: lgdt3306a: Set fe ops.release to
NULL if probed")
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A possible hardware bug was discovered when using CA addon hardware
attached to the ngene hardware, in that the TS input buffer much likely
will shift and thus become unaligned to 188 byte blocks (a full TS frame)
when things like CA module initialisation (which happens via differing
communication paths) take place. This causes the TS NULL removal in
tsin_exchange() to fail to detect this previously inserted data and thus
causes userspace applications to receive data they didn't sent beforehand
and ultimately cause troubles.
On driver load with an inserted CAM, buffers are fine at first (note that
the driver has to keep the communication running from/to the card by
inserting TS NULL frames, this is done in tsout_exchange() via
FillTSBuffer() - that data is simply sent back by the hardware):
offset | 0 1 2 3 4 5 .... 188 189 190 191 192 193 .... 376
data | 47 1f ff 10 6f 6f .... 47 1f ff 10 6f 6f .... 47
After a few seconds, the CA module is recognised and initialised, which is
signalled by
dvb_ca_en50221: dvb_ca adapter X: DVB CAM detected and initialised successfully
This is where the first shift happens (this is always four bytes), buffer
becomes like this:
offset | 0 1 2 3 4 5 .... 188 189 190 191 192 193 .... 376
data | 6f 6f 6f 6f 47 1f .... 6f 6f 6f 6f 47 1f .... 6f
Next, VDR, TVHeadend or any other CI aware application is started, buffers
will shift by even more bytes. It is believed this is due to the hardware
not handling control and data bytes properly distinct, and control data
having an influence on the actual data stream, which we cannot properly
detect at the driver level.
Workaround this hardware quirk by adding a detection for the TS sync byte
0x47 before each TS frame copy, scan for a new SYNC byte and a TS NULL
packet if buffers become unaligned, take note of that offset and apply
that when copying data to the DVB ring buffers. The last <188 bytes from
the hardware buffers are stored in a temp buffer (tsin_buffer), for which
the remainder will be in the beginning of the next hardware buffer (next
iteration of tsin_exchange()). That remainder will be appended to the
temp buffer and finally sent to the DVB ring buffer. The resulting TS
stream is perfectly fine, and the TS NULL packets inserted by the driver
which are sent back are properly removed. The resulting offset is being
clamped to 188 byte segments (one TS packet). Though this can result in
a repeated TS packet if the overall offset grows beyond this (and it
will grow only on CA initialisation), this is still way better than
unaligned TS frames and data sent to userspace that just isn't supposed
to be there.
This compensation can be toggled by the ci_tsfix modparam, which defaults
to 1 (enabled). In the case of problems, this can be turned off by setting
the parameter to 0 to restore the old behaviour.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the copy logic that will skip previously inserted TS NULL frames when
moving data to the DVB ring buffers into an own function. This is done to
not duplicate code all over the place with the following TS offset shift
fixup patch.
While we're touching this part of the code, get rid of the DEBUG_CI_XFER
debug-ifdeffery. This could be toggleable either by a Kconfig or a module
param, but in the end this will accidentally be enabled and cause lots
of kernel log messages, and such devel debug shouldn't be there anyway.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On some architectures such as arm64, siano chip based TV-tuner
USB devices are not recognized correctly due to coherent memory
allocation failure with the following error:
[ 663.556135] usbcore: deregistering interface driver smsusb
[ 683.624809] smsusb:smsusb_probe: board id=18, interface number 0
[ 683.633530] smsusb:smsusb_init_device: smscore_register_device(...) failed, rc -12
[ 683.641501] smsusb:smsusb_probe: Device initialized with return code -12
[ 683.652978] smsusb: probe of 1-1:1.0 failed with error -12
This is caused by dma_alloc_coherent(NULL, ...) returning NULL in
smscoreapi.c.
To fix this error, allocate the buffer memory for the USB devices
via kmalloc() and let the USB core do the DMA mapping and free.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ">" should be ">=" so that we don't read one element beyond the end
of the array.
Fixes: 8a77009be4 ("media: ov5695: add support for OV5695 sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update the register 0x3503 to use 'no delay latch' for gain.
This makes sensor to output the first frame as normal rather
than a very dark one.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The PM runtime operations are unused when CONFIG_PM is disabled,
leading to a harmless warning:
drivers/media/platform/renesas-ceu.c:1003:12: error: 'ceu_runtime_suspend' defined but not used [-Werror=unused-function]
static int ceu_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/renesas-ceu.c:987:12: error: 'ceu_runtime_resume' defined but not used [-Werror=unused-function]
static int ceu_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~
This adds a __maybe_unused annotation to shut up the warning.
Fixes: 32e5a70dc8 ("media: platform: Add Renesas CEU driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CSTRST_CPON mask was wrongly assigned to BIT(1) instead of BIT(0).
Fix that by changing the mask opportunely.
Reported-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As all drivers using the cxd2099 are converted to handle attach/detach
the generic I2C client way, the static inline cxd2099_attach isn't
required anymore. Thus cleanup cxd2099.h from the remainders, the adr
struct member also isn't used anymore.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
